inet_ntoa() and inet_ntoa_r() take the address in network
byte-order. When I removed those calls, I should have
replaced them with ntohl() to make the hex addresses slightly
less unreadable. Here they are.
See r315277 regarding classic blunders.
vangyzen: you're deep in "no good deed" territory, it seems
--badger
Reported by: ian
MFC after: 3 days
MFC when: I finally get it right
Sponsored by: Dell EMC
When I made the changes in r313821, I fell victim to one of the
classic blunders, the most famous of which is: never get involved
in a land war in Asia. But only slightly less well known is this:
Keep your brain turned on and engaged when making a tedious, sweeping,
mechanical change. KTR can correctly log the immediate integral values
passed to it, as well as constant strings, but not non-constant strings,
since they might change by the time ktrdump retrieves them.
Reported by: glebius
MFC after: 3 days
Sponsored by: Dell EMC
It was implemented to reduce context switches when uploading firmware to
card's RAM. But this mechanism is not used last 10 years since all mbox
operations are now polled, and it was never used for cards produced in
last 15 years. Newer cards can use DMA to upload firmware.
MFC after: 2 weeks
This change fixes DMA resource leak on driver unload. Also it removes
DMA resources allocation for hardcoded number of requests before fetching
the real number from firmware. Also it prepares ground for more flexible
IRQs allocation according to firmware capabilities.
MFC after: 2 weeks
- unconditionally enable BUS_DMA on non-x86 architectures
- speed up rxd zeroing via customized function
- support out of order updates to rxd's
- add prefetching to hardware descriptor rings
- only prefetch on 10G or faster hardware
- add seperate tx queue intr function
- preliminary rework of NETMAP interfaces, WIP
Submitted by: Matt Macy <mmacy@nextbsd.org>
Sponsored by: Limelight Networks
Make sure that uinput state field reflects actual state by checking
evdev_register result for errors
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Differential Revision: https://reviews.freebsd.org/D9320
hardware but lack the larger fifos rev 5 hardware should have.
The linux world (where our FDT data comes from) solved this by adding
a new property to pl011 nodes, "arm,primecell-periphid". When this
property is present, its values override the values in the hardware
periphid registers. For pl011 rev 5 hardware with small fifos, they
override the id so that it appears to be rev 4 hardware.
The driver now uses the new property when present. It also continues
to check the device compat string, to handle older fdt data that may
still be in use on existing systems (on RPi systems it is common to
update system software without updating fdt data which is part of the
boot firmware).
Reviewed by: imp
- XPT_NOTIFY_ACKNOWLEDGE was not handled, causing stuck requests.
- XPT_ABORT was not even trying to abort active ATIOs/INOTs.
- Initiator's tag was not stored and not used where needed.
- List of TM request types needed update.
- mpt_scsi_tgt_status() missed some useful debugging.
After this change global TM requests, such as reset, should work properly.
ABORT TASK (ABTS) requests are still not passes to CTL, that is not good
and should be fixed.
MFC after: 2 weeks
user default normal attribute to the current attribute).
This change only fixes a logic error. scterm_clear() used to be
used for terminal reset, but teken uses a general fill function for
that, leaving scterm_clear() only used for initialization and mode
change, when using the user default attribute is correct. It is not
really a terminal function, but needs to sync its changes with the
terminal layer. Syncing of the attribute is currently broken for
terminal reset, but works for initialization and mode change.
some cases of initialization and resetting of the teken cursor position.
(This bad name is consistent with others, but it is too easy to confuse
with scteken_cursor() which goes in the opposite direction.)
The following cases were broken:
- for booting without a syscons console, the teken and sc positions for
ttyv0 were (0, 0), but are supposed to be somewhere in the middle of
the screen (after carefully preserved BIOS and loader messages) (at
least if there is no mode switch that loses the messages).
- after mode switches, the screen is cleared and the cursor is supposed to
be moved to (0, 0), but it was only moved there for sc.
The following case was hacked to work:
- for booting with a syscons console, it was arranged that scteken_init()
for the console could see a nonzero cursor position and adjust, although
this broke the sc seeing it in the non-console case above.
They cannot be used anymore with the userland bits we provide.
Furthermore, their KMS versions support the same hardware.
Submitted by: dumbbell
Reviewed by: emaste, manu
Sponsored by: AsiaBSDCon
Differential Revision: https://reviews.freebsd.org/D5614
looked like it might handle reverse attributes, but it actually handles
conversion of attributes in the direction indicated by the new name.
Reverse attributes are just broken.
Rename scteken_attr() to scteken_te_to_sc_attr(). scteken_attr() looked
like it might give teken attributes, but it actually gives sc attributes.
Change scteken_te_to_sc_attr() to return int instead of unsigned int.
u_char would be enough, and it promotes to int, and syscons uses int
or u_short for its attributes everywhere else (u_short holds a shifted
form and it promotes to int too).
This change just does cleanups missed in r56043 17 years ago. The
default attributes were still stored in structs for the purpose of
changing them and passing around pointers to the defaults, but r56043
added another layer that made the defaults invariant and only used for
initialization and reset. Just use the defaults directly. This was
already done for the kernel defaults. The defaults for reverse
attributes aren't actually used, but are ignored in layers that no
longer support them.
- Not set BufferLength caused receive of empty ATIOs.
- CDB length guessing was broken at least for RC16.
- mpt_req_untimeout() was called with wrong req parameter.
- Sense data reporting was broken in several ways.
With this change my LSI7204EP-LC can pass at least basic tests as target.
The code is still far from perfect, but finally I found second hw/driver
after isp(4) that really can work in CAM target mode.
MFC after: 2 weeks
is unavailable on sparc64 only. This makes the new ec_putc() a non-op
on sparc64 but still calls it. On other non-x86 arches, it should
compile but might not work.
Reported by: gjb
Starting with rev 5 (which is inexplicably indicated by a version number
of '3' in the Peripheral ID register), the pl011 doubled the size of the
rx and tx fifos, to 32 bytes, so read the ID register and set the size
variables in the softc accordingly.
An interesting wrinkle in this otherwise-simple concept is that the
bcm2835 SoC, used in Raspberry Pi systems among others, has the rev 5
pl011 hardware, but somehow also has the older 16-byte fifos. We check
the FDT data to see if the hardware is part of a bcm283x system and use
the smaller size if so.
Thanks to jchandra@ for pointing out that newer hardware has bigger fifos.
Some drives sometimes have errors for things like setting the number
of queue entries in the submission queue. The error paths taken for
these drives ensure a panic dereferencing uninialized data.
Sponsored by: Netflix
as kernel drivers and their dependency onto mmc(4); this allows for
incrementing the mmc(4) module version but also for entire omission
of these bridge declarations for mmccam(4) in a single place, i. e.
in dev/mmc/bridge.h.
Fix assumptions about name spaces in NVME driver. First, it assumes
cdata.nn is the number of configured devices. However, it is the
number of supported name spaces. Second, it assumes that there will
never be more than 16 name spaces supported, but a certain drive I'm
testing reports 1024. It assumes that name spaces are a tightly packed
namespace, but the standard seems to indicate otherwise. Finally, it
assumes that an error would be generated when quearying an
unconfigured namespace. Instead, it succeeds but the identify data is
all zeros.
Fix these by limiting the number of name spaces we probe to 16. Remove
aborting when we find one in error. When the size of the name space is
zero, ignore it.
This is admittedly a bandaide. The long term fix will be to
participate in the enumeration and name space change protocols
definfed in the NVNe standard.
Sponsored by: Netflix
This change tries to fix the most obvious locking problems.
sbp_cam_scan_lun() is never called with the sbp lock held, so the lock
needs to be acquired internally (if it's needed at all).
Without this change a kernel with INVARIANTS panics when a firewire disk
is connected:
panic: mutex sbp not owned at /usr/src/sys/dev/firewire/sbp.c:967
KDB: stack backtrace:
db_trace_self_wrapper() at 0xffffffff80420bbb = db_trace_self_wrapper+0x2b/frame 0xfffffe0504df0930
kdb_backtrace() at 0xffffffff80670359 = kdb_backtrace+0x39/frame 0xfffffe0504df09e0
vpanic() at 0xffffffff8063986c = vpanic+0x14c/frame 0xfffffe0504df0a20
panic() at 0xffffffff806395b3 = panic+0x43/frame 0xfffffe0504df0a80
__mtx_assert() at 0xffffffff8061c40d = __mtx_assert+0xed/frame 0xfffffe0504df0ac0
sbp_cam_scan_lun() at 0xffffffff80474667 = sbp_cam_scan_lun+0x37/frame 0xfffffe0504df0af0
xpt_done_process() at 0xffffffff802aacfa = xpt_done_process+0x2da/frame 0xfffffe0504df0b30
xpt_done_td() at 0xffffffff802ac2e5 = xpt_done_td+0xd5/frame 0xfffffe0504df0b80
fork_exit() at 0xffffffff805ff72f = fork_exit+0xdf/frame 0xfffffe0504df0bf0
fork_trampoline() at 0xffffffff8082483e = fork_trampoline+0xe/frame
0xfffffe0504df0bf0
--- trap 0, rip = 0, rsp = 0, rbp = 0 ---
Also, I tried to reduce the scope of the sbp lock to avoid holding it
while doing bus_dma allocations.
The code badly needs some re-engineering. SBP really should implement
a CAM transport, so that it avoids control flow inversion when re-scanning
the bus. Also, the sbp lock seems to be too coarse.
Additionally, the commit includes some changes not related to locking.
- sbp_cam_scan_lun: restore CAM_DEV_QFREEZE before re-queueing the ccb
because xpt_setup_ccb resets ccb_h.flags
- sbp_post_busreset: call xpt_release_simq only if it's actually frozen
- don't place private SIMQ_FREEZED flag (sic, "freezed") into sim->flags,
use sbp->flags for that
- some style fixes and control flow enhancements
Reviewed by: sbruno
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D9898
Currently netfront is setting the flags of inbound packets with the checksum
not present (offloaded) to (CSUM_IP_CHECKED | CSUM_IP_VALID | CSUM_DATA_VALID |
CSUM_PSEUDO_HDR). According to the mbuf(9) man page this is not the correct
combination of flags, it should instead be (CSUM_DATA_VALID |
CSUM_PSEUDO_HDR).
Reviewed by: Wei Liu <wei.liu2@citrix.com>
MFC after: 2 weeks
Sponsored by: Citrix Systems R&D
Differential revision: https://reviews.freebsd.org/D9831
Lock the xenstore request mutex when suspending user-space processes, in order
to prevent any process from holding this lock when going into suspension, or
else the xenstore suspend process is going to deadlock.
Submitted by: Liuyingdong <liuyingdong@huawei.com>
Reviewed by: royger
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D9638
When running on Xen, it's possible that a suspend request to the hypervisor
fails (return from HYPERVISOR_suspend different than 0). This means that the
suspend hasn't succeed, and the resume procedure needs to properly handle this
case.
First of all, when such situation happens there's no need to reset the vector
callback, hypercall page, shared info, event channels or grant table, because
it's state is preserved. Also, the PV drivers don't need to be reset to the
initial state, since the connection with the backed has not been interrupted.
Submitted by: Liuyingdong <liuyingdong@huawei.com>
Reviewed by: royger
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D9635
comments, marking unused parameters as such, style(9), whitespace,
etc.
o In the mmc(4) bridges and sdhci(4) (bus) front-ends:
- Remove redundant assignments of the default bus_generic_print_child
device method (I've whipped these out of the tree as part of r227843
once, but they keep coming back ...),
- use DEVMETHOD_END,
- use NULL instead of 0 for pointers.
o Trim/adjust includes.
This is mostly a version bump to stay in version number sync with firmware.
The only change there was cosmetic: Display degraded speed message upon
receiving Active Cable Exception Event with DEGRADED reason code.
Discussed with: slm@
MFC after: 1 week
all the clocks that they provide.
Each clocks are exported under the node 'clock.<clkname>' and have the following
children nodes :
- frequency
- parent (The selected parent, if any)
- parents (The list of parents, if any)
- childrens (The list of childrens, if any)
- enable_cnt (The enabled counter)
This give us the possibility to examine clocks at runtime and make graph of
the clock flow.
Reviewed by: mmel
MFC after: 2 month
Differential Revision: https://reviews.freebsd.org/D9833
For 4965 just extract 'is_chan_5ghz' flag from the RXON structure
(like it was done in r281287); for others it was never used.
Tested with Intel 6205, STA mode.
have been in the code all along, but were masked by having a fifo depth of
one byte at the hardware level, so everything kinda worked by accident.
The hardware interrupts when the TX fifo is half empty, so set
sc->sc_txfifosz to 8 bytes (half the hardware fifo size) to match. This
eliminates dropped characters on output.
Restructure the read loop to consume all the bytes in the fifo by using
the "rx fifo empty" bit of the flags register rather than the "rx ready"
bit of the interrupt status register. The rx-ready interrupt is cleared
when the number of bytes in the fifo fall below the interrupt trigger
level, leaving the fifo half full every time receive routine was called.
Now it loops until the fifo is completely empty every time (including
when the function is called due to a receive timeout as well as for
fifo-full).
Modern GCC and Clang simply ignore the qualifier, while the old base GCC
produces a warning (treated as an error in the kernel build).
Approved by: cem
MFC after: 5 days
it in emergency in sc_cnputc().
Locking fixes in sc_cnputc() previously turned off normal output in
near-deadlock conditions and added deferred output which might never
be completed. Emergency output goes to the frame buffer using
sufficiently atomic non-blocking writes if the console is in text
mode (in graphics mode, nothing is done, modulo races setting the
graphics mode bit). Screen updates overwrite the emergency output
if the emergency condition clears enough to reach them.
ec_putc() also works for "early" console output in normal x86 text
mode as soon as this mode is initialized (if ever). This uses a
hard-coded x86 frame buffer address before cninit() and a hopefully
MI address after cninit(). But non-x86 is more likely to not support
text mode, when ec_putc() will be null. ec_putc() has no dependencies
of syscons before cninit(), and only has them later to track syscons'
mode changes. This commit doesn't attach ec_putc() for early use.
To test emergency use, put a breakpoint in central syscons output code
like sc_puts() and do some user output. The system used to race or
deadlock in ddb output soon after entry to ddb. The locking fixes
deferred the output until after leaving ddb, so ddb was unusable and
you had to try typing c[ontinue] blindly until it exited, or better use
a serial console in parallel. Now the output goes to a window in the
middle 2/3 of the screen. Scrolling is circular and there is no cursor,
but otherwise ec_putc() provides full dumb terminal functionality and
very fast output that hides artificates from dumb overwrites.
by the CPU number.
This was originally for debugging near-deadlock conditions where
multiple CPUs either deadlock or scramble each other's output trying
to report the problem, but I found it interesting and sometimes
useful for ordinary kernel messages. Ordinary kernel messages
shouldn't be interleaved, but if they are then the colorization
makes them readable even if the interleaving is for every character
(provided the CPU printing each message doesn't change).
The default colors are 8-15 starting at 15 (bright white on black)
for CPU 0 and repeating every 8 CPUs. This works best with 8 CPUs.
Non-bright colors and nonzero background colors need special
configuration to avoid unreadable and ugly combinations so are not
configured by default. The next bright color after 15 is 8 (bright
black = dark gray) is not very readable but is the only other color
used with 2 CPUs. After that the next bright color is 9 (bright
blue) which is not much brighter than bright black, but is used with
3+ CPUs. Other bright colors are brighter.
Colorization is configured by default so that it gets tested. It can
only be turned off by configuring SC_KERNEL_CONS_ATTR to anything other
than FG_WHITE. After booting, all colors can be changed using the
syscons.kattr sysctl. This is a SYSCTL_OPAQUE, and no utility is
provided to change it (sysctl only displays it).
The default colors work in all VGA modes that I could test. In 2-color
graphics modes, all 8 bright colors are displayed as bright white, so
the colorization has no effect, but anything with a nonzero background
gives white on white unless the foreground is zero. I don't have an
mono or VGA grayscale hardware to test on. Support for mono mode seems
to have never worked right in syscons (I think bright white gives white
underline with either bold or bright), but VGA grayscale should work
better than 2-color graphics.
I imagine that the module would be useful only to a very limited number
of developers, so that's my excuse for not writing any documentation.
On a more serious note, please see DRAM Error Injection section of BKDGs
for families 10h - 16h. E.g. section 2.13.3.1 of BKDG for AMD Family 15h
Models 00h-0Fh Processors.
Many thanks to kib for his suggestions and comments.
Discussed with: kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9824
ULPs can set a qp's state to ERROR and then post a work request on the
sq and/or rq. When the reply for that work request comes back it is
guaranteed that all previous work requests posted on that queue have
been drained.
Obtained from: Chelsio Communications
MFC after: 3 days
Sponsored by: Chelsio Communications
registered. T4/5/6 have no internal limit on this size. This is
probably a copy paste from the T3 iw_cxgb driver.
MFC after: 3 days
Sponsored by: Chelsio Communications
TW_CL_MAX_NUM_LUNS should not be 16 but I presume 255. I have a 3ware
controller with more than 16 volumes (LUN's) and otherwise all LUN's
above the 16'th are not working.
Submitted by: jcatrysse <j.catrysse@proximedia.be>
Pull Request: https://github.com/freebsd/freebsd/pull/100
left-click event. It can be disabled setting the new
hw.usb.wsp.enable_single_tap_clicks sysctl to 0.
Submitted by: K Staring <qdk@quickdekay.net>
Pull Request: https://github.com/freebsd/freebsd/pull/97
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
Sockets representing the TCP endpoints for iWARP connections are
allocated by the ibcore module. Before this revision they were closed
either by the ibcore module or the iw_cxgbe hardware driver depending on
the state transitions during connection teardown. This is error prone
and there were cases where both iw_cxgbe and ibcore closed the socket
leading to double-free panics. The fix is to let ibcore close the
sockets it creates and never do it in the driver.
- Use sodisconnect instead of soclose (preceded by solinger = 0) in the
driver to tear down an RDMA connection abruptly. This does what's
intended without releasing the socket's fd reference.
- Close the socket in ibcore when the iWARP iw_cm_id is destroyed. This
works for all kinds of sockets: clients that initiate connections,
listeners, and sockets accepted off of listeners.
Reviewed by: Steve Wise @ Open Grid Computing, hselasky@
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D9796
SBP-2 specification defined maximum CDB length as 12 bytes. Newer SBP-3
specification allows CDB of any size, but this driver is too old. Proper
solution would be to look on maximal ORB size supported by the target.
MFC after: 1 week
RSS hash type will be used to identify the CPU on to which, a receive packet
will be queued. This patch extracts the "RSS hash type" from the receive
completion and sends it to the stack.
Submitted by: Venkatkumar Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed by: shurd
Approved by: sbruno
MFC after: 1 week
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D9685
2. add sysctl to set pause frame parameters
3. increase max segs for TSO packets to BXE_TSO_MAX_SEGMENTS (32)
4. add debug messages for PHY
5. HW LRO support restricted to FreeBSD versions 8.x and above.
Submitted by:Vaishali.Kulkarni@cavium.com
MFC after:5 days
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
vm_map_lookup_done should only be called when the gntdev has finished poking at
the entry.
Reported by: alc
Reviewed by: alc
MFC after: 1 week
Sponsored by: Citrix Systems R&D
During acpi_cmbat_attach() the acpi_cmbat_init_battery() notification
handler is registered. It has been observed this notification handler
can be called instantly, before the attach routine has returned. In
the notification handler there is a call to device_is_attached() which
returns false. Because the softc is set we know an attach is in
progress and the fix is simply to wait and try again in this case.
Reviewed by: avg @
MFC after: 1 week
The pl011 UART has a 16 entry Tx FIFO and a 16 entry Rx FIFO that
have not been used so far. Update the driver to enable the FIFOs
and use them in transmit and receive.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D8819
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
Its more important for SPI HBAs, as they don't support CDBs above 12 bytes.
The new error code makes CAM to fall back to alternative commands.
MFC after: 2 weeks
This allows to properly handle cases when target wants to receive or send
more data then initiator wants to send or receive. Previously in such
cases isp(4) returned CAM_DATA_RUN_ERR, while now it returns resid > 0.
MFC after: 2 weeks
This change removes limitation of single S/G list entry and limitation on
maximal I/O size, using multiple data transfers per I/O if needed. Also
it removes code duplication between send and receive paths, which are now
completely equal.
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
pcib_request_feature allows drivers to request the firmware (ACPI)
release certain features it may be using. ACPI normally manages things
like hot plug, advanced error reporting and other features until the
OS requests ACPI to relenquish control since it is taking over.
Sponsored by: Netflix
- Check return code from initialization path; otherwise, vap state
may be wrong after an error.
- Do not try to run iwn_stop() / iwn_init() multiple times.
- Merge iwn_radio_on/off() and move RFKILL bit check into the task.
- Try to handle possible RF switch state change in S3 state (PR 181694).
PR: 181694
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9797
On Core2 and older Intel CPUs, where TSC stops in C2, system does not
allow C2 entrance if timecounter hardware is TSC. This is done by
tc_windup() which tests for TC_FLAGS_C2STOP flag of the new
timecounter and increases cpu_disable_c2_sleep if flag is set. Right
now init_TSC_tc() only sets the flag if cpu_deepest_sleep >= 2, but
TSC is initialized too early for this variable to be set by
acpi_cpu.c.
There is no reason to require that ACPI reported C2 and deeper states
to set TC_FLAGS_C2STOP, so remove cpu_deepest_sleep test from
init_TSC_tc() condition. And since this is the only use of the
variable, remove it at all.
Reported and submitted by: Jia-Shiun Li <jiashiun@gmail.com>
Suggested by: jhb
MFC after: 2 weeks
* Uses the IWM_FW_PAGING_BLOCK_CMD firmware command to tell the firmware
what memory ranges to use for paging.
Obtained from: dragonflybsd.git 8a5b199964f8e7bdb00039f0b48817a01b402f18
VXGE_DEFAULT_TTI_RTIMER_VAL and VXGE_DEFAULT_RTI_RTIMER_VAL have value
zero but nevertheless we should use the right value on each.
Pointed by: jhb
X-MFC with: r314145
One test was inadvertently expecting a bug in the kernel's sscanf
implementation circa 2012. I don't know when that bug got fixed.
Reported by: royger
Reviewed by: royger
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9766
Most of these are null pointer dereferences or missing error checks in the
unit tests. One is a missing error check in xnb_attach_failed. None can
cause real problems in running systems.
Reported by: Coverity
CIDs: 1092469 1092468 1092467 2092466 1092465 1092512 1092511 1092510
CIDs: 1092510 1092509 1092508 1092507
Reviewed by: royger
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9234
The code is not operational right now so just comment away an obviously
useless assignment. Fix some typos while here.
Found with: coccinelle (da.cocci)
The Xen grant table device treats the mmap offset parameter as an unsigned
type, and as so it must use the newly introduced UOFF_TO_IDX.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
X-MFC-with: r313690
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
Note that the timer itself fully supports suspension, but due to the lack of
ordering during the resume process FreeBSD cannot guarantee that the timer is
resumed before any device attempts to use it.
Submitted by: Liuyingdong <liuyingdong@huawei.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D9639
- Move private data about ATIOs/INOTs from per-LUN to per-channel data.
This allows active commands to continue operation after LUN destruction.
This also simplifies lookup of the data by tag in some situations.
- Unify three restart_queue processing implementations.
- Complete all ATIOs from restart_queue on LUN disable.
- Delete ATIO private data when command completed or aborted, not depending
on the ATIO being requeued, that was ugly hack and could never happen. CAM
should always call ether XPT_CONT_TARGET_IO with status or XPT_ABORT.
- Implement XPT_ABORT for queued ATIOs/INOTs to allow CAM do graceful
shutdown, not depending on LUN disable, as it is done in ahd(4)/targ(4).
- Unify isp_endcmd() arguments to make it more usable in generic code.
- Remove never really used LUN state reference counter.
MFC after: 2 weeks
* This is more similar to how code/definitions are distributed in
Linux's iwlwifi.
* This should make recognizing new chipset variants, and adding additional
flags from the Linux iwlwifi code easier, without blowing up if_iwm.c
Obtained from: dragonflybsd.git 27d11320e707d2c41424efc1983762f6799941d6
* Just add the struct iwm_cfg pointers to the iwm_devices array, to get
rid of the large switch clause.
Obtained from: dragonflybsd.git 35f0e6c86c1654323d6b19f7a077f4ab8ac85868
* The sc->sc_uc.uc_error_event_table value is now at sc->error_event_table,
and not sc->umac_error_event_table.
Obtained from: dragonflybsd.git 612855b1a8c321ec9ba34f63edf913e7ecff8363
* Use the notification wait API, like it's done in the Linux iwlwifi code,
to wait for the IWM_MVM_ALIVE notification.
* This also should fix some firmware load interrupt issues, and errors
in the nic lock using.
Tested:
* (adrian) Intel 7260, STA mode
Obtained from: dragonflybsd.git a7697ea01c11fd493aec52260a02f31df680eb91
* While there, rename some functions to match the names and functionality
of the similarly named functions in Linux iwlwifi.
Obtained from: dragonflybsd.git e98ee77a816bfd8b4912047b93dfb2c560788f24
For some reason isp_handle_platform_notify_fc() allocated INOT just
before calling isp_handle_platform_target_tmf(), which also allocates
INOT. It seems to be a braino introduced in r196008.
MFC after: 2 weeks
* Migrate the rx_params stuff out from ieee80211_freebsd.h where it doesn't belong -
this isn't freebsd specific anymore.
* Don't use a hard-coded number of chains in the ioctl header; now we can shuffle
MAX_CHAINS around so it can be used in the right spot.
* Extend the signal/noisefloor levels in the mimo stats struct to userland to include
the signal and noisefloor levels for each 20MHz slice of a 160MHz channel.
* Bump the number of EVM pilots in preparation for 4x4 and 160MHz channels.
Tested:
* ath(4), STA mode
* iwn(4), STA mode
* local ath10k port, STA mode
TODO:
* 11ax chips will come with 5GHz 8x8 hardware for lots of MU-MIMO - I'll re-bump it
at that point.
Note:
* This breaks the driver and ifconfig ABI; please recompile the kernel,
ifconfig and wpa_supplicant/hostapd.
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
All resources lack of which may put CTIO into the queue are either
per-channel or potentially per-queue, but none of them are per-LUN.
This is a first step to fix live LUN disabling. Before this change
any CTIOs held in a queue in time of disabling were just leaked.
MFC after: 2 weeks
Do no write to PBA register on igb(4) devices unless we need
to make adjustments for the 82575 and jumbo frames.
Remove redundant LPE/~LPE assignments.
Move e1000_lv_jumbo_workaround_ich8lan() invokcation into a block
so that its not executed in the igb case.
Move em(4) class assignments of RCTL values to its own code block.
Adjust a few direct accesses of ifp->mtu to use accessor functions.
PR: 216734
Submitted by: Kaho Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>
This patch will add support for MacBookPro 11.2.
For the macros, the MBP11_* macros (for the existing MacBookPro11.3) did not
match so they have been renamed to MBP113_* and a new MBP112_* has been
added (modified copy of MBP11_*).
Some trailing whitespaces may have been removed automatically.
PR: kern/214836
Obtained from: Johannes Lundberg <johannes@brilliantservice.co.jp
compile options. Remove doxygen pointers to now deleted files. Remove
EISA and VME as examples in bus_space.9.
Retained EISA mode code for IO PIC and MPTABLES because that's not
EISA bus, per se, and some people have abused EISA to mean "EISA-like
behavior as opposed to ISA" rather than using it for EISA add-in
cards.
Relnotes: yes
VesaLocalBus or EISA. Internally, EISA and ISA are handled the same,
with VL being handled slightly differently. To avoid too much code
churn, retain the EISA name, despite it being used only for ISA
bus. When it is on the ISA bus, weird gymnastics are required with
EISA-space address accesses as well. Remove known models from the ahc
man page. Remove ahc_eisa module.
page. Remove comment about EISA dual channel card. Remove trivial
references in advlib to avoid false positives with grep. Remove stray
MCA reference not worth a seperate commit.
still relevant (ISA cards can still be in EISA mode, and we're still
ignoring those in the identify routine). Notes about cards in EISA
mode have been left in the manual since they aren't relevant to EISA
support, but instruct how to properly configure an ISA card in a mode
when it is in a ISA bus slot.
support. Fix a comment block that's shared with both vx and ep. Remove
obsolete refernce to statically compiling a kernel with a fixed number
of vx devices. Have not removed EISA from the title of the document
the register definitions were originally derived from (though no doubt
more recent docments were also consulted).
inet_ntoa() cannot be used safely in a multithreaded environment
because it uses a static local buffer. Instead, use inet_ntoa_r()
with a buffer on the caller's stack.
Suggested by: glebius, emaste
Reviewed by: gnn
MFC after: 2 weeks
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D9625
machines, only a few 486 machines that used it, and those haven't had
enough memory to run FreeBSD for quite some time (often limited to
16MB).
Not to be confused with the Machine Check Architecture, which is still
very much alive and used (and untouched by this commit).
No Objection From: arch@
I found that at least with Chelsio NICs TOE sockets quite often report
negative sbspace() values. Using unsigned variable to store it resulted
in attempts to aggregate too much data in one sosend() call, that caused
errors and following connection termination.
MFC after: 2 weeks
The {powerpc,powerpc64,sparc64} LINT kernel builds fail with this error:
sys/dev/vt/vt_buf.c:198: warning: 'vtbuf_htw' defined but not used
Move vtbuf_htw() inside the '#if SC_NO_CUTPASTE' block where it belongs, and
put it in the proper order.
This fixes the immedate issue w/ vt(4), but all three then fail on different
issues.
Reviewed by: emaste
Current bxe probe function won't attach to devices with the NetXtreme II
BCM57840 2x20GbE chip, enable it by adding it's chip ID to the list of
supported chips.
Tested on: HP ProLiant WS460c Gen9
Reviewed by: gnn
MFC after: 1 week
Sponsored by: Citrix Systems R&D
Differential Revision: https://reviews.freebsd.org/D9609
we will import a newer version of the Linux code so the linuxkpi was not
used.
This is still missing 10G support, and multicast has not been tested.
Reviewed by: gnn
Obtained from: ABT Systems Ltd
Sponsored by: SoftIron Inc
Differential Revision: https://reviews.freebsd.org/D8549
On laptops like the ThinkPad X240, ClickPad buttons are located at the
top. The hw.psm.synaptics.softbuttons_y sysctl was supposed to allow this
by setting the value to a negative one (e.g. -1700). However, the
condition was wrong (double negative), and doing that placed the buttons
in an unreachable area.
PR: 216342
Submitted by: Greg V <greg@unrelenting.technology>
MFC after: 1 week
All this code is based on assumption that data will be stored in one piece,
and since buffer size if known and fixed, it is easier to hardcode it.
MFC after: 2 weeks
In general case m_pullup() does not really guarantee any data alignment.
Instead of depenting on side effects caused by data being always copied
out of mbuf cluster (which is probably a bug by itself), always allocate
aligned BHS buffer and read data there directly from socket.
While there, reuse new icl_conn_receive_buf() function to read digests.
The code could probably be even more optimized to aggregate those reads,
but until that done, this is still easier then the way it was before.
MFC after: 2 weeks
Add ACPI device 80860F14 with _UID 3 to the list of known devices. It
make SD card available on NUCs and Minnowboard. Previously added _UID 1
covered only eMMC devices.
Reported by: kib@
MFC after: 1 week
ip_data_mbuf is always appended to ip_bhs_mbuf, so it does not need own
packet header. This change first avoids allocation/initialization of the
header, and then avoids dropping one when it later gets to socket buffer.
MFC after: 2 weeks
meta-data, copy it into the softc structure.
When returning md(4) device details to the caller, include the file name in
any MD_PRELOAD type devices if it is set (first character is not NUL.)
In mdconfig, for "preload" type md(4) devices, if there is file config
available, print it in the file column of the output.
Reviewed by: brooks
Approved by: sjg (mentor)
MFC after: 1 month
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D9529
Return full channel list via iwi_getradiocaps() method
(ieee80211_init_channels() was replaced with iwi_getradiocaps()
to be consistent with other drivers).
PR: 216923
Submitted and tested by: ds@ukrhub.net (original patch)
MFC after: 5 days
em_local_timer() executions during normal operation and was very likely
to cause a lock up on igb(4) devices.
Submitted by: Matt Macy (mmacy@nextbsd.org)
Reported by: jtl
Reviewed by: gallatin
Sponsored by: Limelight Networks & Netflix
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
The isp(4) driver was changing the tag type for REQUEST SENSE
commands to Head of Queue, when the CAM CCB flag
CAM_TAG_ACTION_VALID was NOT set. CAM_TAG_ACTION_VALID is set
when the tag action in the XPT_SCSI_IO is not CAM_TAG_ACTION_NONE
and when the target has tagged queueing turned on.
In most cases when CAM_TAG_ACTION_VALID is not set, it is because
the target is not doing tagged queueing. In those cases, trying to
send a Head of Queue tag may cause problems. Instead, default to
sending a simple tag.
IBM tape drives claim to support tagged queueing in their standard
Inquiry data, but have the DQue bit set in the control mode page
(mode page 10). CAM correctly detects that these drives do not
support tagged queueing, and clears the CAM_TAG_ACTION_VALID flag
on CCBs sent down to the drives.
This caused the isp(4) driver to go down the path of setting the
tag action to a default value, and for Request Sense commands only,
set the tag action to Head of Queue.
If an IBM tape drive does get a Head of Queue tag, it rejects it with
Invalid Message Error (0x49,0x00). (The Qlogic firmware translates that
to a Transport Error, which the driver translates to an Unrecoverable
HBA Error, or CAM_UNREC_HBA_ERROR.) So, by default, it wasn't possible
to get a good response from a REQUEST SENSE to an FC-attached IBM
tape drive with the isp(4) driver.
IBM tape drives (tested on an LTO-5 with G9N1 firmware and a TS1150
with 4470 firmware) also have a bug in that sending a command with a
non-simple tag attribute breaks the tape drive's Command Reference
Number (CRN) accounting and causes it to ignore all subsequent
commands because it and the initiator disagree about the next
expected CRN. The drives do reject the initial command with a head
of queue tag with an Invalid Message Error (0x49,0x00), but after that
they ignore any subsequent commands. IBM confirmed that it is a bug,
and sent me test firmware that fixes the bug. However tape drives in
the field will still exhibit the bug until they are upgraded.
Request Sense is not often sent to targets because most errors are
reported automatically through autosense in Fibre Channel and other
modern transports. ("Modern" meaning post SCSI-2.) So this is not
an error that would crop up frequently. But Request Sense is useful on
tape devices to report status information, aside from error reporting.
This problem is less serious without FC-Tape features turned on,
specifically precise delivery of commands (which enables Command
Reference Numbers), enabled on the target and initiator. Without
FC-Tape features turned on, the target would return an error and
things would continue on.
And it also does not cause problems for targets that do tagged
queueing, because in those cases the isp(4) driver just uses the
tag type that is specified in the CCB, assuming the
CAM_TAG_ACTION_VALID flag is set, and defaults to sending a Simple
tag action if it isn't an ordered or head of queue tag.
sys/dev/isp/isp.c:
In isp_start(), don't try to send Request Sense commands
with the Head of Queue tag attribute if the CCB doesn't
have a valid tag action. The tag action likely isn't valid
because the target doesn't support tagged queueing.
Sponsored by: Spectra Logic
MFC after: 3 days
When using Blue-Flame, BF, the QPN overrides the VLAN, CV, and SV
fields in the WQE. Thus, BF may only be used for QPNs with bits 6,7
unset.
The current ethernet driver code reserves a TX QP range with 256b
alignment.
This is wrong because if there are more than 64 TX QPs in use, QPNs >=
base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for "Eth
QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have bits
6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required
attributes for this QP. Those attributes are considered "best-effort".
If an attribute, such as Ethernet BF enabled QP, is a must-have
attribute, the function has to check that attribute is supported
before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those
attributes and masks out unsupported attributes as well. In order to
notify VFs which attributes are supported, the VF uses QUERY_FUNC_CAP
command. This command's mailbox is filled by the PF, which notifies
which QP allocation attributes it supports.
Obtained from: Linux (dual BSD/GPLv2 licensed)
Submitted by: Dexuan Cui @ microsoft . com
Differential Revision: https://reviews.freebsd.org/D8868
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
Previously, the mlx4 driver queried the firmware in order to get the
number of supported EQs. Under SRIOV, since this was done before the
driver notified the firmware how many VFs it actually needs, the
firmware had to take into account a worst case scenario and always
allocated four EQs per VF, where one was used for events while the
others were used for completions. Now, when the firmware supports the
asymmetric allocation scheme, denoted by exposing num_sys_eqs > 0 (-->
MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the QUERY_FUNC command to query
the firmware before enabling SRIOV. Thus we can get more EQs and MSI-X
vectors per function. Moreover, when running in the new
firmware/driver mode, the limitation that the number of EQs should be
a power of two is lifted.
Obtained from: Linux (dual BSD/GPLv2 licensed)
Submitted by: Dexuan Cui @ microsoft . com
Differential Revision: https://reviews.freebsd.org/D8867
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
The hpt27xx(4), hptnr(4), and hptrr(4) drivers declare MIN() and MAX()
internally which match the macros from sys/param.h.
MIN() is not used, MAX is only used once and can be replaced with the
max() version in libkern.h which operates on u_ints.
MFC after: 2 weeks
Refresh upstream driver before impending conversion to iflib.
Major new features:
- Support for Fortville-based 25G adapters
- Support for I2C reads/writes
(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).
- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.
Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation
This implements hardware assisted quiet IE support. Quiet time is
an optional interval on DFS channels (but doesn't have to be DFS
only channels! sigh) where the station and AP can be quiet in order
to allow for channel utilisation measurements. Typically that's
stuff like radar detection, spectral scan, other-BSS frame sniffing,
checking how busy the air is, etc.
The hardware implements it as one of the generic timers, which is
supplied a period, offset from the trigger period and duration
to stay quiet. The AP can announce quiet time configurations which
change, and so this code also tracks that.
Implementation details:
* track the current quiet time IE
* compare the new one against the previous one - if only the TBTT
counter changes, don't update things
* If tbttcount=1 then program it into the hardware - that is when
it is easiest to program the correct starting offset (one TBTT +
configured offset).
* .. later on check to see if it can be done on any tbttcount
* If the IE goes away then remove the quiet timer and clear the
config
* Upon reset, state change, new beacon - clear quiet time IE
and just let it resync from the next beacon.
History:
This was work done initially by sibridgetech.com in 2011/2012/2013
as part of some FreeBSD wifi DFS contracting work they had for a
third party. They implemented the net80211 quiet time IE pieces
and had some test code for the station side which didn't entirely
use the timers correctly.
I figured out how to use the timers correctly without stopping/starting
the transmit DMA engine each time. When done correctly, the timer
just needs to be programmed once and left alone until the next
configuration change.
So, thanks to Himali Patel and Parthiv Shah for their work way
back then. I finally figured it out and finished it!
TODO:
* Now, I'd rather net80211 did the quiet time IE tracking and parsing,
pushing configurations into the driver is needed. I'll look at
doing that in a subsequent update.
* This doesn't handle multiple quiet time IEs, which will currently
just mess things up. I'll look into supporting that in the future
(at least by only obeying "one" of them, and then ignoring
subsequent IEs in a beacon/probe frame.)
* This also implements the STA side and not the AP side - the AP
side will come later, and involves taking various other intervals
into account (eg the beacon offset for multi-VAP modes, the
SWBA time, etc, etc) as well as obtaining the configuration when
a beacon is configured/generated rather than "hearing" an IE.
* .. investigate supporting quiet IE in mesh, tdma, ibss modes
* .. investigate supporting quiet IE for non-DFS channels
(so this can be done for say, 2GHz channels.)
* Chances are i should commit NULL methods for the ar5210, ar5211 HALs..
Tested:
* AR9380, STA mode - announcing quiet, removing quiet, changing quite
time config, whilst doing iperf testing;
* AR9380, AP mode.
Some U-Boot versions do not initialize MT7620's Frame Engine.
Then it is not possible to receive packets from the network.
Setting GDMA1 Frames Destination Port to Port 0 (CPU) in GDM Forwarding
Configuration register solves this issue.
Submitted by: Hiroki Mori (yamori813@yahoo.co.jp)
Reviewed by: adrian mizhka (previous version)
Differential Revision: https://reviews.freebsd.org/D9301
using the ACPI C1/mwait sleep method.
Previously, the mwait instruction would return when an interrupt was
pending; however, the idle loop did not actually enable interrupts when
this occurred. This led to a situation where the idle loop could quickly
spin through the C1/mwait sleep method a number of times when an interrupt
was pending. (Eventually, the situation corrected itself when something
other than an interrupt triggered the idle loop to either enable interrupts
or schedule another thread.)
Reviewed by: kib, imp (earlier version)
Input from: jhb
MFC after: 1 week
Sponsored by: Netflix
The 1s delay was added in the update to version 16 fw, where Family 8000
support was added.
Obtained from: DragonflyBSD commit bb480ca679a7ea530bdca6e41082d5755e9751dc
* Add the command groups enum, and the iwm_phy_ops_subcmd_ids enum
to if_iwmreg.h definitions.
* The IWM_DTS_MEASUREMENT_NOTIF_WIDE notification will be generated by
version 17 firmware.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit 4d8d6f9def2ffb60aaf2d88f72f069a96c0b4e3f
* Adds IWM_DEBUG_TEMP debug message type, for printing messages related
to temperature sensors and thermal/TDP infos.
* The firmware regularly sends us DTS measurement notifications, so just
print the temperature value as a debugging message.
(Adrian's addition):
* Eventually this can be used by the driver to limit transmit rate / power to
try and do some thermal throttling.
Obtained from: DragonflyBSD commit efb7d4eb5c3140889a8880e12fd83c7bbfd0059d
* Add iwm_pcie_set_cmd_in_flight() and iwm_pcie_clear_cmd_in_flight()
helper methods.
* Use ring->queued tracking in the command queue to set/clear the
cmd_hold_nic_awake bit at the right points.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit ce43f57f5308b579ea21e8a5a29969114ba2247d
* Add IWM_FLAG_SCAN_RUNNING to sc->sc_flags to track whether the firmware
is currently running a scan, in order to decide wheter iwm_scan_end
needs to abort a running scan.
* In iwm_scan_end, if the scan is still running, we now abort it, in order
to keep the firmware scanning state in sync.
* Try to make things a bit simpler, by reacting on the
IWM_SCAN_OFFLOAD_COMPLETE and IWM_SCAN_COMPLETE_UMAC notifications,
instead of IWM_SCAN_ITERATION_COMPLETE and
IWM_SCAN_ITERATION_COMPLETE_UMAC. This should be fine since we always
only tell the firmware to do a single scan iteration anyway.
Obtained from: DragonflyBSD commit 1f249c981c4e89e7cde1836a75b61cac36dc7ac5
* Uses the notification wait api to wait for the corresponding scan
complete notification after sending the abort command.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit b484d09d54301740f036ddf02008117f563960c2
* This also fixes one of many small nic lock handling bugs, and matches
iwlwifi's code.
Obtained from: DragonflyBSD git 50787d03cd0a0366c9cc4a055bb6977e5f65c85d
'-n' to tell the driver to create _up to_ 'n' queues if enough cores are
available. For example, setting hw.cxgbe.nrxq10g="-32" will result in
16 queues if the system has 16 cores, 32 if it has 32.
There is no change in the default number of queues of any type.
MFC after: 1 week
Sponsored by: Chelsio Communications
* This fixes the phy_cfg field sent in the iwm_send_phy_cfg_cmd()
command, which wasn't taking into account the valid_rx_ant and
valid_tx_ant masks from nvm_data before.
Tested:
* 7260, STA mode, 2G and 5G
Obtained from: DragonflyBSD commit cbb82693c18fd71b4eb86855b82d03995f352d65
* This makes it a bit easier to factor out common parts for e.g. the
7000 chipset family.
* Add iwm7265d config, and recognize the 7265D chipset variant via the
hardware revision.
Tested:
* 7260, STA mode (2ghz)
Obtained from: Dragonflybsd commit cc8d6ccf5583fd45964f3bde9b057ee4f834c0e0
* sc->sc_nvm becomes sc->nvm_data and is now a pointer instead of an
inlined struct.
* Add sc->eeprom_size and sc->nvm_hw_section_num configuration values to
struct iwm_softc.
* For now continue to avoid negative error return-values, and use pointer
variables for some return values, as before.
* Continue to omit LAR (location aware regulatory) related code as well.
Tested:
* Intel 7260, STA mode (2GHz)
Obtained from: dragonflybsd commit 39f8331b1a6f295291e08c377da12a8e7a5436c0
The tty layer uses tsw_busy to poll for busy/idle status of the transmitter
hardware during close() and tcdrain(). The ucom layer defines ULSR_TXRDY and
ULSR_TSRE bits for the line status register; when both are set, the
transmitter is idle. Not all chip drivers maintain those bits in the sc_lsr
field, and if the bits never get set the transmitter will always appear
busy, causing hangs in tcdrain().
These changes add a new sc_flag bit, UCOM_FLAG_LSRTXIDLE. When this flag is
set, ucom_busy() uses the lsr bits to return busy vs. idle state, otherwise
it always returns idle (which is effectively what happened before this
change because tsw_busy wasn't implemented).
For the uftdi chip driver, these changes stop masking out the tx idle bits
when processing the status register (because now they're useful), and it
calls ucom_use_lsr_txbits() to indicate the bits are maintained by the
driver and can be used by ucom_busy().
Differential Revision: https://reviews.freebsd.org/D9183
As of r313097, the HotPlug code requires the link to support
reporting of the data-link status. Remove tests for this capability
from code that can now assume its presence.
Suggested by: jhb
Reviewed by: jhb
MFC after: 3 days
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D9431
Some PCI-e bridges report that they support HotPlug in the slot
capabilities but do not report support for Data Layer Active events
in the link capabilities register. These bridges do not work correctly
when HotPlug is used. Further, while the description of HotPlug in
the spec does not mention that DL active events are required, the
description of the link capabilities register says that DL active is
required for HotPlug. Thanks to Dave Baukus for finding that language
in the spec.
PR: 211699
Submitted by: Dave Baukus <daveb@spectralogic.com>
Reviewed by: vangyzen
MFC after: 3 days
Commit r312743 ("Use SoC ID - based detection in CESA") resulted
in build failing for Marvell armv5 platforms, which don't support
the newer version of CESA controller. This patch provides a fix by
removing ifdefs around bitfields' definitions, so that they are
known to all platforms.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
- Check for Chelsio vendor ID in probe routines.
- Fail attach instead of faulting if pci_find_dbsf() doesn't find a
device.
PR: 216539
Reported by: asomers
Tested by: Dave Baukus <daveb@spectralogic.com>
MFC after: 3 days
Sponsored by: Chelsio Communications
structure:
if_gethwtsomax(), if_sethwtsomax() - if_hw_tsomax
if_gethwtsomaxsegcount(), if_sethwtsomaxsegcount() - if_hw_tsomaxsegcount
if_gethwtsomaxsegsize(), if_sethwtsomaxsegsize() - if_hw_tsomaxsegsize
Update em and vnic drivers which had already been coverted to use accessor
functions for the other ifnet structure members.
Reviewed by: erj
Approved by: sjg (mentor)
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D8544
Thought it's difficult to reproduce, I think this variable was responsible
for a use-after-free panic when a SATA disk timed out responding to a SATA
identify command during boot.
Submitted by: slm
Reviewed by: slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9364
Clang complains about the shift of (1 << 7) into a int8_t changing the value:
warning: implicit conversion from 'int' to 'int8_t' (aka 'signed char') changes
value from 128 to -128 [-Wconstant-conversion]
Squash this warning by forcing clang to see it as an unsigned bit.
This seems odd, given that it's still a conversion of 128->-128, but I'm
guessing the explicit unsigned attribute notifies clang that sign really doesn't
matter in this case.
Reported by: Mark Millard <markmi AT dsl-only DOT net>
MFC after: 2 weeks
driver to support exposing a GEOM device, which can be used to mount
Avalon-attached ROMs, reserved areas of DRAM, etc, as a filesystem:
commit 9deb1e60eaaaf7a3687e48c58af5efd756f32ec6
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Sat Mar 5 20:33:12 2016 +0000
Use format strings with make_dev(9) in avgen(4).
commit 0bf2176c23e7425bfa042c08a24f8a25fe6d8885
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Tue Mar 1 10:23:23 2016 +0000
Implement a new "geomio" configuration argument to altera_avgen(4),
the generic I/O device we attach to various BERI peripherals. The new
option requests that, instead of exposing the underlying device via a
special device node in /dev, it instead be exposed via geom(4),
allowing it to be used with filesystems. The current implementation
does not allow a device to be exposed both for file/mmap and geom, so
one of the two models must be selected when configuring it via FDT or
device.hints. A typical use of the new option will be:
sri-cambridge,geomio = "rw";
MFC after: 1 week
Sponsored by: DARPA, AFRL
CheriBSD, which attempt to work around an inherent race in the UART's
control-register design in detecting whether JTAG is currently,
present, which will otherwise lead to moderately frequent output
drops when running in polled rather than interrupt-driven operation.
Now, these drops are quite infrequent.
commit 9f33fddac9215e32781a4f016ba17eab804fb6d4
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Jul 16 17:34:12 2015 +0000
Add a new sysctl, hw.altera_jtag_uart.ac_poll_delay, which allows the
(default 10ms) delay associated with a full JTAG UART buffer combined
with a lack of a JTAG-present flag to be tuned. Setting this higher
may cause some JTAG configurations to be more reliable when printing
out low-level console output at a speed greater than the JTAG UART is
willing to carry data. Or it may not.
commit 73992ef7607738b2973736e409ccd644b30eadba
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Sun Jan 1 15:13:07 2017 +0000
Minor improvements to the Altera JTAG UART device driver:
- Minor rework to the logic to detect JTAG presence in order to be a bit
more resilient to inevitable races: increase the retry period from two
seconds to four seconds for trying to find JTAG, and more agressively
clear the miss counter if JTAG has been reconnected. Once JTAG has
vanished, stop prodding the miss counter.
- Do a bit of reworking of the output code to frob the control register
less by checking whether write interrupts are enabled/disabled before
changing their state. This should reduce the opportunity for races
with JTAG discovery (which are inherent to the Altera
hardware-software interface, but can at least be minimised).
- Add statistics relating to interrupt enable/disable/JTAG
discovery/etc.
With these changes, polled-mode JTAG UART ttys appear substantially
more robust.
MFC after: 1 week
Sponsored by: DARPA, AFRL
undo_offload_socket() is only called by t4_connect() during a connection
setup failure, but t4_connect() still owns the TOE PCB and frees ita
after undo_offload_socket() returns. Release a reference in
undo_offload_socket() resulted in a double-free which panicked when
t4_connect() performed the second free. The reference release was
added to undo_offload_socket() incorrectly in r299210.
MFC after: 1 week
Sponsored by: Chelsio Communications
The intended use is to annotate frequently used globals which either rarely
change (and thus can be grouped in the same cacheline) or are an atomic counter
(which means it may benefit from being the only variable in the cacheline).
Linker script support is provided only for amd64. Architectures without it risk
having other variables put in, i.e. as if they were not annotated. This is
harmless from correctness point of view.
Reviewed by: bde (previous version)
MFC after: 1 month
Recent changes in the pseudo header accessor prototypes start to
use common code RxQ handle on datapath. The handle was located
at the end of the structure with members not used on datapath.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9359
TxQ is destroyed on stop and last used tag should be reset to default 0
on the next start.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9358
The MLX5 driver has four different types of DMA allocations which are
now allocated using busdma:
1) The 4K firmware DMA-able blocks. One busdma object per 4K allocation.
2) Data for firmware commands use the 4K firmware blocks split into four 1K blocks.
3) The 4K firmware blocks are also used for doorbell pages.
4) The RQ-, SQ- and CQ- DMA rings. One busdma object per allocation.
After this patch the mlx5en driver can be used with DMAR enabled in
the FreeBSD kernel.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- When device disappears from PCI indicate error device state and:
1) Trigger command completion for all pending commands
2) Prevent new commands from executing and return:
- success for modify and remove/cleanup commands
- failure for create/query commands
3) When reclaiming pages for a device in error state don't ask FW to
return all given pages, just release the allocated memory
MFC after: 1 week
Sponsored by: Mellanox Technologies
PCI device(s), changes:
- alloc_entry() now clears bit for page slot entry aswell
- update of cmd->ent_arr[] is now under cmd->alloc_lock
- complete command if alloc_entry() fails
MFC after: 1 week
Sponsored by: Mellanox Technologies
By default reading the diagnostic counters is disabled. The firmware
decides which counters are supported and only those supported show up
in the dev.mce.X.diagnostics sysctl tree.
To enable reading of diagnostic counters set one or more of the
following sysctls to one:
dev.mce.X.conf.diag_general_enable=1
dev.mce.X.conf.diag_pci_enable=1
MFC after: 1 week
Sponsored by: Mellanox Technologies
consistent return values from the mlx5e_sq_has_room_for()
function. The two counters are incremented by different threads under
different locks.
MFC after: 1 week
Sponsored by: Mellanox Technologies
* Although the hardware is awake, the power state handling doesn't think so.
So just explicitly wake it up early in setup so ath_hal calls don't complain.
* We shouldn't be transmitting or ACKing frames during DFS CAC or on passive
channels before we hear a beacon. So, start laying down comments in the
places where this work has to be done.
Note:
* The main bit missing from finishing this particular bit of work is a state
call to transition a VAP from passive to non-passive when a beacon is heard.
CAC is easy, it's an interface state. So, I'll go and add a method to control
that soon.
Taking closer look on my ASM1062 I found that it has bunch of issues around
error recovery: reported wrong CCS, failed commands reported as completed,
READ LOG EXT times out after NCQ error. This patch workarounds first two
problems, that were making ATAPI devices close to unusable on these HBAs.
MFC after: 2 weeks
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It occurred that some Marvell integrated controllers
require additional time after soft reset to work properly.
Introduce new quirk (AHCI_Q_MRVL_SR_DEL), that enable
such operation.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: mav
Differential revision: https://reviews.freebsd.org/D9221
method
Method could be used before we can access device_t structure.
As per simple phandle_t handle we can access FDT to check
if specified node has been enabled.
It will be used in Marvell's common configuration code.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb, meloun-miracle-cz
Differential revision: https://reviews.freebsd.org/D9218
Adding SHA256 support to Marvell crypto driver resulted in regression
for older SoC's, not capable of handling this mode in hardware.
Submitted by: Emeric Poupon <emeric.poupon@stormshield.eu>
Obtained from: Stormshield
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9215
This commit introduces following changes in order to get rid of
ifdef's from all around the driver.
* Introduce sc_soc_id field in cesa_softc structure - this value is
obtained in cesa_attach() anyway, so make use of it.
* Replace ifdefs with SoC ID checks.
* Perform PM control status only for relevant SoC's.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9247
Marvell Armada 38x is supported in 3 variants,
so take all into consideration in crypto driver
attach routine.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9248
Add internal tracking of smp startup status to reliably figure out
what methods are to be used to get gtaskqueue up and running.
e1000:
Calculating this pointer gives undefined behaviour when (last == -1)
(it is before the buffer). The pointer is always followed. Panics
occurred when it points to an unmapped page. Otherwise, the pointed-to
garbage tends to not have the E1000_TXD_STAT_DD bit set in it, so in the
broken case the loop was usually null and the function just returned, and
this was acidentally correct.
Submitted by: bde
Reported by: Matt Macy <mmacy@nextbsd.org>
Add internal tracking of smp startup status to reliably figure out
what methods are to be used to get gtaskqueue up and running.
e1000:
Calculating this pointer gives undefined behaviour when (last == -1)
(it is before the buffer). The pointer is always followed. Panics
occurred when it points to an unmapped page. Otherwise, the pointed-to
garbage tends to not have the E1000_TXD_STAT_DD bit set in it, so in the
broken case the loop was usually null and the function just returned, and
this was acidentally correct.
Submitted by: bde
Reviewed by: Matt Macy <mmacy@nextbsd.org>
