The newer hardware revisions of the Raspberry Pi 4 removed the ability of
the VIA VL805 xhci controller to load its own firmware. Instead the
firmware must be installed at the appropriate time by the VideoCore
coprocessor.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25261
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
sure the XHCI controller is reset after halting it. The problem is
clearly a BIOS bug as the suspend and resume is failing without
loading the XHCI driver. The same happens when using Linux and the
XHCI driver is not loaded.
Submitted by: Yanko Yankulov <yanko.yankulov@gmail.com>
PR: 216261
MFC after: 1 week
version of the XHCI specification. Make sure the code can handle the
maximum number of allowed scratch pages.
Submitted by: Shichun_Ma@Dell.com
Approved by: re (hrs)
MFC after: 1 week
requesting the initial complete device descriptor and not as part of
the subsequent babble error recovery. Babble means that the received
USB packet was bigger than than configured maximum packet size. This
only affects enumeration of FULL speed USB devices which use a
bMaxPacketSize different from 8 bytes. This patch might help fix
enumeration of USB devices which exhibit USB I/O errors in dmesg
during boot.
MFC after: 1 week
available. As with MSI interrupts these can be disabled by setting
hw.usb.xhci.msix to 0 in the loader.
MSI-X interrupts are needed on some hardware, for example the Cavium
ThunderX only supports them, and with this we don't fall back to polling.
PR: 204378
Reviewed by: hselasky, jhb
MFC after: 1 week (after r292669)
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4698
scatter-gather XHCI TRB entries for its payload data. The XHCI
controller can handle at least 65536 bytes per scatter-gather list
entry.
MFC after: 1 week
Suggested by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
- Simplify MSI allocation to what is actually needed for a single one.
- Release the MSI and the corresponding bus resource as appropriate when
either the interrupt resource cannot be allocated or setting up the
interrupt fails.
- Error out when interrupt allocation or setup fails and polling is
disabled.
- Release the MSI after the corresponding bus resource so the former is
not leaked on detach.
- Remove a redundant softc member.
MFC after: 3 days
ports. The current bitmap array was too small to hold more than 16
bits and would at some point toggle the context size, which then would
trigger an enumeration fault and cause a fallback to the EHCI
companion controller, if any.
MFC after: 3 days
routing if we get certain errors. Poll for command completion upon
command timeouts. The XHCI error events might not generate interrupts.
MFC after: 1 week
Reported by: Daniel Gerzo <danger@rulez.sk>, Antonis Anastasiadis <anastasiadis@datalive.gr>
PR: usb/181159
Approved by: re (gjb)
the regular interrupt handler is not working properly or
in case of MSI interrupts which are not yet supported.
Remove interrupt setup code for FreeBSD versions older
than 700031.
MFC after: 1 week
PR: usb/179342
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
in SUPER-speed mode, USB 3.0.
This feature has not been tested yet, due to lack of hardware.
This feature is useful when implementing protocols like UASP,
USB attached SCSI which promises higher USB mass storage throughput.
This patch also implements support for hardware processing of endpoints
for increased performance. The switching to hardware processing
of an endpoint is done via a callback to the USB controller driver. The
stream feature is implemented like a variant of a hardware USB protocol.
USB controller drivers implementing device mode needs to be updated to
implement the new "xfer_stall" USB controller method and remove the
"xfer" argument from the "set_stall" method.
The API's toward existing USB drivers are preserved. To setup a USB transfer
in stream mode, set the "stream_id" field of the USB config structure to
the desired value.
The maximum number of BULK streams is currently hardcoded and limited to 8
via a define in usb_freebsd.h.
All USB drivers should be re-compiled after this change.
LibUSB will be updated next week to support streams mode. A new IOCTL to
setup BULK streams as already been implemented. The ugen device nodes
currently only supports stream ID zero.
The FreeBSD version has been bumped.
MFC after: 2 weeks
scratch. This driver adds support for USB3.0 devices. The XHCI
interface is also backwards compatible to USB2.0 and USB1.0 and will
evntually replace the OHCI/UHCI and EHCI drivers.
There will be follow-up commits during the coming week to link the
driver into the default kernel build and add missing USB3.0
functionality in the USB core. Currently only the driver files are
committed.
Approved by: thompsa (mentor)
