Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
This patch adds hwtype parameter which keeps information about hardware
revision of Marvell EHCI controller. It allows to replace multiple
calls to ofw_bus_is_compatible with comparing hwtype value during driver
initialization.
Submitted by: Patryk Duda <pdk@semihalf.com>
Suggested by: ian
Obtained from: Semihalf
Sponsored by: Semihalf
This patch reuses ehci_mv driver by adding a support for the new
compatible string and adding ehci_mv.c to list of available options
for arm64 platforms.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12255
This driver will be used by Marvell Armada 3700 and 7k/8k SoC families.
The same, generic xhci device also appears in Armada 380, so we are reusing
driver.
This patch also adds xhci_mv.c entry to the arm64 files list.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12252
It turns out that this is more than a power optization. The OTG port
won't work on boards that have this property unless this setting is honored.
Also ensure that the usb phy device attaches before ehci.
programmed for infinite IN token retry after NAK, the SAF1761
hardware, however, does not retry the IN-token. This problem is
described in the SAF1761 errata, section 18.1.1.
While at it:
- Add some minor chip specific initialization for RTEMS.
- Add debug print for status registers in the interrupt filter.
Submitted by: Christian Mauderer <christian.mauderer@embedded-brains.de>
MFC after: 1 week
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
sure the XHCI controller is reset after halting it. The problem is
clearly a BIOS bug as the suspend and resume is failing without
loading the XHCI driver. The same happens when using Linux and the
XHCI driver is not loaded.
Submitted by: Yanko Yankulov <yanko.yankulov@gmail.com>
PR: 216261
MFC after: 1 week
When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().
Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.
While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.
Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070
MFC after: 2 weeks
This should have been committed in r307093: resource allocation depends
on source of the device tree. upstream dts has extra interrupt that we can
ignore
its own job because this breaks the simplified QEMU XHCI TRB parser,
which expects the complete USB control transfer as a series of back to
back TRBs. The old behaviour is kept under #ifdef in case this change
breaks enumeration of any USB devices.
PR: 212021
MFC after: 1 week
configuring of EP0 and non-EP0 into xhci_cmd_evaluate_ctx() and
xhci_cmd_configure_ep() respectivly. This resolves some errors when
using XHCI under QEMU and gets is more in line with the XHCI
specification.
PR: 212021
MFC after: 1 week
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
only for now, but wouldn't be too difficult to add support for FDT.
Reviewed by: hselasky
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7352
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
version of the XHCI specification. Make sure the code can handle the
maximum number of allowed scratch pages.
Submitted by: Shichun_Ma@Dell.com
Approved by: re (hrs)
MFC after: 1 week
Previously the USB PHY driver would enable all regulators at attach time.
This prevented boards from booting when powered by the USB OTG port, as
it didn't take VBUS presence into consideration.
If platform support EXT_RESOURCES, clocks and resets are handled out of
the box.
If not driver can be subclassed using the generic_usb interface.
generic_usb name was choosed because at one point I'll add generic-ehci
FDT driver.
Reviewed by: jmcneill, hselasky
Approved by: andrew (mentor)
Differential Revision: https://reviews.freebsd.org/D5481
requesting the initial complete device descriptor and not as part of
the subsequent babble error recovery. Babble means that the received
USB packet was bigger than than configured maximum packet size. This
only affects enumeration of FULL speed USB devices which use a
bMaxPacketSize different from 8 bytes. This patch might help fix
enumeration of USB devices which exhibit USB I/O errors in dmesg
during boot.
MFC after: 1 week
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
Driver was modified to ensure it attaches properly to "marvell,orion-ehci"
node, which doesn't have error interrupt line defined. Neccessary
ofw_compat_data struct was added and probe procedure was altered.
Reviewed by: andrew, ian
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4369
available. As with MSI interrupts these can be disabled by setting
hw.usb.xhci.msix to 0 in the loader.
MSI-X interrupts are needed on some hardware, for example the Cavium
ThunderX only supports them, and with this we don't fall back to polling.
PR: 204378
Reviewed by: hselasky, jhb
MFC after: 1 week (after r292669)
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4698
32-bits aligned. Merge the two bounce buffers into a single one. Some
rough tests showed that the DWC OTG throughput on RPI2 increased by
10% after this patch.
MFC after: 1 week
status registers for every interrupt. Check a common host channel
status interrupt register first, then conditionally read the
individual host channel status registers.
Submitted by: Sebastian Huber <sebastian.huber@embedded-brains.de>
MFC after: 1 week
There is an issue with interrupts at the moment, but it works with
polling mode set (hw.usb.xhci.use_polling=1).
Reviewed by: hselasky
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3665
intervals less than 250us was not handled properly. Add support for
high-bandwidth ISOCHRONOUS packets. USB webcams, USB audio and USB DVB
devices are expected to work better. High-bandwidth INTERRUPT
endpoints is not yet supported.
MFC after: 2 weeks
like RPI-B and RPI-2.
Description of problem:
USB transfers can process data in their callbacks sometimes causing
unacceptable latency for other USB transfers. Separate BULK completion
callbacks from CONTROL, INTERRUPT and ISOCHRONOUS callbacks, and give
BULK completion callbacks lesser execution priority than the
others. This way USB audio won't be interfered by heavy USB ethernet
usage for example.
Further serve USB transfer completion in a round robin fashion,
instead of only serving the most CPU hungry. This has been done by
adding a third flag to USB transfer queue structure which keeps track
of looping callbacks. The "command" callback function then decides
what to do when looping.
MFC after: 2 weeks
Remove NAKing limit and pause IN and OUT transactions for 125us in
case of NAK response for BULK and CONTROL endpoints. This gets the
receive latency down and improves USB network throughput at the cost
of some CPU usage.
MFC after: 1 month
xhci_start_controller() to xhci_init(). These values don't change at run-
time so there's no point of acquiring them on every USB_HW_POWER_RESUME
instead of only once during initialization. In r276717, reading the first
couple of registers in question already had been moved as a prerequisite
for the changes in that revision.
- Identify ASMedia ASM1042A controllers.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
1) Use the TX FIFO empty interrupts to poll the transmit FIFO usage,
instead of using own software counters and waiting for SOF
interrupts. Assume that enough FIFO space is available to execute one
USB OUT transfer of any kind when the TX FIFO is empty.
2) Use the host channel halted event to asynchronously wait for host
channels to be disabled instead of waiting for SOF interrupts. This
results in less turnaround time for re-using host channels and at the
same time increases the performance.
The network transmit performance measured by "iperf" for the "RPi-B v1
2011/12" board, increased from 45MBit/s to 65Mbit/s after applying the
changes above.
No regressions seen using:
- High Speed (BULK, CONTROL, INTERRUPT)
- Full Speed (All transfer types)
- Low Speed (Control and Interrupt)
MFC after: 1 month
Submitted by: Daisuke Aoyama <aoyama@peach.ne.jp>
stage processing is only allowed after the setup complete event has
been received. Else a race may occur and the OUT data can be corrupted.
While at it ensure resetting a FIFO has the required wait loop.
MFC after: 3 days
'BUS_PROBE_DEFAULT'. This allows bhyve's 'ppt' driver to claim ownership
of the device and pass it through to the guest.
In the common case where there are no competing drivers for USB controllers
this change is a no-op.
Reviewed by: hselasky
MFC after: 2 weeks
been done by U-Boot. This allows the USB to work when we load the kernel
directly.
No dma sync is performed after these operations as the data we read/write
is not used by the cpu after the calls to the maimbox driver.
Differential Revision: https://reviews.freebsd.org/D1940
Reviewed by: imp, Michal Meloun (meloun AT miracle.cz)
MFC after: 1 Week
Sponsored by: ABT Systems Ltd
when re-enumerating a FULL speed device. Else the wrong max packet
setting might be used when trying to re-enumerate a FULL speed device.
MFC after: 3 days
interrupt status bit. According to the UHCI controller specification
the host controller halted interrupt is non-maskable.
PR: 156596
Tested by: adrian @
MFC after: 1 week
that we should use a normal-TRB if there are more TRBs extending the
data-stage TRB. Add a dedicated state bit to the internal USB transfer
flags to handle this case.
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
MFC after: 1 week
every operation to retrieve the bs_cookie value almost nothing actually uses.
The bus_space struct contains a private data pointer (poorly named bs_cookie,
now renamed to bs_privdata) which is used only by a few old armv4 xscale
implementations. The bus_space functions were all defined to take this
value as the first parameter instead of the bus_space_tag_t, requiring all
the inline macro and function expansions to dereference the tag to pass it
to another function, which never uses it. Now all the functions take the tag
as the first parameter and retrieve the privdata if they need it.
Also fix a couple bus_space_unmap() implementations that were calling
kva_free() instead of pmap_unmapdev().
Discussed with: cognet
simultaneously detaching kernel drivers on the same USB device we can
get stuck in the "usb_wait_pending_ref_locked()" function because the
conditions needed for allowing detach are not met. The "destroy_dev()"
function waits for all system calls involving the given character
device to return. Character device system calls may lock the USB
enumeration lock, which is also held when "destroy_dev()" is
called. This can sometimes lead to a deadlock not noticed by
WITNESS. The current solution is to ensure the calling thread is the
only one holding the USB enumeration lock and prevent other threads
from getting refs while a USB device detach is ongoing. This turned
out not to be sufficient. To solve this deadlock we could use
"destroy_dev_sched()" to schedule the device destruction in the
background, but then we don't know when it is safe to free() the
private data of the character device. Instead a callback function is
executed by the USB explore process to kill off any leftover USB
character devices synchronously after the USB device explore code is
finished and the USB enumeration lock is no longer locked. This makes
porting easier and also ensures us that character devices must
eventually go away after a USB device detach.
While at it ensure that "flag_iserror" is only written when "priv_mtx"
is locked, which is protecting it.
MFC after: 5 days
scatter-gather XHCI TRB entries for its payload data. The XHCI
controller can handle at least 65536 bytes per scatter-gather list
entry.
MFC after: 1 week
Suggested by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
is called from "xhci_configure_reset_endpoint()". Ensure the 3-strikes
error feature is always enabled except for ISOCHRONOUS transfers.
MFC after: 1 week
Suggested by: marius@
- Simplify MSI allocation to what is actually needed for a single one.
- Release the MSI and the corresponding bus resource as appropriate when
either the interrupt resource cannot be allocated or setting up the
interrupt fails.
- Error out when interrupt allocation or setup fails and polling is
disabled.
- Release the MSI after the corresponding bus resource so the former is
not leaked on detach.
- Remove a redundant softc member.
MFC after: 3 days
