controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
current@ and stable@ for the locking patches. The driver can always be
revived if someone tests it.
This driver also sleeps in its if_init routine, so it likely doesn't really
work at all anyway in modern releases.
the serial console speed (i386 and amd64 only). If the previous
stage boot loader requested a serial console (RB_SERIAL or RB_MULTIPLE)
then the default speed is determined from the current serial port
speed. Otherwise it is set to 9600 or the value of BOOT_COMCONSOLE_SPEED
at compile time.
This makes it possible to set the serial port speed once in
/boot.config and the setting will propagate to boot2, loader and
the kernel serial console.
user to interrupt autoboot process at all. Currently, even when
`autoboot_delay' is set to 0, loader(8) still allows autoboot process to be
interrupted by pressing any key on the console when the loader reads kernel
and modules from the disk. In some cases (i.e. untrusted environment) such
behaviour is highly indesirable and user should not be allowed to interfere
with the autoboot process at all.
Sponsored by: PBXpress Inc.
MFC after: 3 days
will prepend the current kernel booting... This prevents a problem of
loading /boot/kernel's modules when a different kernel has no modules,
but you left your module_load="YES" in loader.conf...
Reviewed by: dcs (minus the help part)
bootp -> BOOTP
bootp.nfsroot -> BOOTP_NFSROOT
bootp.nfsv3 -> BOOTP_NFSV3
bootp.compat -> BOOTP_COMPAT
bootp.wired_to -> BOOTP_WIRED_TO
- i.e. back out the previous commit. It's already possible to
pxeboot(8) with a GENERIC kernel.
Pointed out by: dwmalone
BOOTP -> bootp
BOOTP_NFSROOT -> bootp.nfsroot
BOOTP_NFSV3 -> bootp.nfsv3
BOOTP_COMPAT -> bootp.compat
BOOTP_WIRED_TO -> bootp.wired_to
This lets you PXE boot with a GENERIC kernel by putting this sort of thing
in loader.conf:
bootp="YES"
bootp.nfsroot="YES"
bootp.nfsv3="YES"
bootp.wired_to="bge1"
or even setting the variables manually from the OK prompt.
pf/pflog/pfsync as modules. Do not list them in NOTES or modules/Makefile
(i.e. do not connect it to any (automatic) builds - yet).
Approved by: bms(mentor)
assure backward compatibility (conditional on !BURN_BRIDGES), look it up
by its old name first, and log a warning (but accept the setting) if it
was found. If both the old and new name are defined, the new name takes
precedence.
Also export vm.kmem_size as a read-only sysctl variable; I find it hard to
tune a parameter when I don't know its default value, especially when that
default value is computed at boot time.
queue items that can be allocated by netgraph and the number of free queue
items that are cached on a private list.
Netgraph places an upper limit on the number of queue items it may allocate.
When there is a large number of netgraph messages travelling through the
system (100k/sec and more) there is a high probability, that messages get
queued at the nodes and netgraph runs out of queue items. In this case the data
flow through netgraph gets blocked. The tuneable for the number of free
items lets one trade memory for performance.
The tunables are also available as read-only sysctls.
PR: kern/47393
Reviewed by: julian
Approved by: jake (mentor)
this is called /boot/nextboot.conf. This file is required to have it's first
line be nextboot_enable="YES" for it to be read. Also, this file is
rewritten by the loader to nextboot_enable="NO"<space> after it is read.
This makes it so the file is read exactly once. Finally, the nextboot.conf
is removed shortly after the filesystems are mounted r/w.
Caution should be taken as you can shoot yourself in the foot. This is only
the loader piece. There will be a tool called nextboot(8) that will manage
the nextboot.conf file for you. It is coming shortly.
Reviewed by: dcs
Approved by: jake (mentor)
loader variable, which let users specify the root mount point
the exact way one does after booting the kernel.
Let's take this opportunity to document it...
around. If the kernel boots successfully, the record of this kernel
is erased, it is intended to be a one-shot option for testing
kernels.
This could be improved by having the loader remove the record of
the next kernel to boot, it is currently removed in /etc/rc immediately
after disks are mounted r/w.
I'd like to MFC this before the 4.6 freeze unless there is violent
objection.
Reviewed by: Several on IRC
MFC after: 4 days
This allows obtaining crash dumps from the panics occured during late stages
of kernel initialisation before system enters into single-user mode.
MFC after: 2 weeks
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
