Post-cold sleep instead of DELAY when waiting for firmware.
Convert softc mutex to an SX lock. Change all waits to sleeps
once interrupts are enabled (and it is safe to sleep).
Submitted by: Matt Macy <matt@mattmacy.io>
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D12101
These firmwares come from a pre-release snapshot. The final firmwares
in this Chelsio release cycle will likely be .61.0 or later and those
will be the next "long lived" firmwares in FreeBSD head and stable
branches. .59 is being provided in head (only) for wider test exposure.
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
Tuffli had submitted a more thorough patch that I was unaware of when
I did my work and this brings in the bits I missed from that patch.
PR: 220267
Submitted by: Chuck Tuffli
This adds support in pass(4) for data to be described with a
scatter-gather list (sglist) to augment the existing (single) virtual
address.
Differential Revision: https://reviews.freebsd.org/D11361
Submitted by: Chuck Tuffli
Reviewed by: imp@, scottl@, kenm@
Provided a better estimate for the number of transactions that can be
pending at one time. This will be number of queues * number of
trackers / 4, as suggested by Jim Harris. This gives a better estimate
of the number of transactions that CAM should queue before applying
back pressure. This should be revisted when we have real multi-queue
support in CAM and the upper layers of the I/O stack.
Sponsored by: Netflix
creating hardware VIs.
This fixes a bad race on systems with hw.cxgbe.num_vis > 1.
Reported by: olivier@
MFC after: 1 week
Sponsored by: Chelsio Communications
according to the enabled interface capability bits. Also remove
some dead code, which tried to preserve already set contents of
E1000_WUC while that register is completely overwritten shortly
after in all cases.
This fixes interrupt storms on hardware using legacy level-triggered
interrupts, since doorbell processing could take time after interrupt
handler completion, that triggered extra interrupts in a loop.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Since the doorbell bit is already set when interrupt handler is called,
the event was not propagated to upper layer. It was working normally
because present code was not using masking actively, but that is going
to change.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This feature comes from the fact that we rely memory-backed md(4)
in our build process heavily. However, if the build goes haywire
the allocated resources (i.e. swap and memory-backed md(4)'s) need
to be purged. It is extremely useful to have ability to attach
arbitrary labels to each of the virtual disks so that they can
be identified and GC'ed if neecessary.
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D10457
Tx power values can easily fit into uint8_t + only 8 bits are written
to registers; values may overflow only in case if ROM contains
malformed data (but limit is checked anyway).
Tested with RTL8188CUS, dev.rtwn.1.debug=0x2000 (no changes).
commit it to make initiazation less chatty in the normal case, and more useful
and informative when real debugging is turned on.
Reviewed by: ken (earlier version)
Sponsored by: Netflix
recieve descriptors for the igb(4) class of devices. This will
allow a better definition for maximum going forward. Some igb(4)
devices support more than the default 4K.
Reported by: Jason (j@nitrology.com)
Sponsored by: Limelight Networks
o Automomous Power State Transition
o Host Memory Buffer
o Timestamp
o Keep Alive Timer
o Host Controlled Thermal Management
o Non-Operational Power State Config
Also note that feature codes 0x78-0x7f are reserved for the NVMe
Management Interface.
Sponsored by: Netflix
- map the hard-coded frame buffer address above KERNBASE. Using the
physical address only worked because of larger mapping bugs.
The hard-coded frame buffer address only works on x86. Use messy ifdefs
to try to avoid warnings about unused code for other arches.
- remove the sysctl for reading and writing the table kernel console
attributes. Writing only worked for emergency output since normal
output uses unalterd copies.
- fix the test for the emergency console being usable
- explain why a hard-coded attribute is used very early. Emergency output
works on x86 even before the pcpu pointer is initialized.
Advertise this by changing the defaults to mostly red. If you don't like
this, change them (almost) back using:
vidcontrol -c charcolors,base=7,height=0
vidcontrol -c mousecolors,base=0[,height=15]
The (graphics mode only) mouse cursor colors were hard-coded to a black
border and lightwhite interior. Black for the border is the worst
possible default, since it is the same as the default black background
and not good for any dark background. Reversing this gives the better
default of X Windows. Coloring everything works better still. Now
the coloring defaults to a lightwhite border and red interior.
Coloring for the character cursor is more complicated and mode
dependent. The new coloring doesn't apply for hardware cursors. For
non-block cursors, it only applies in graphics mode. In text mode,
the cursor color was usually a hard-coded (dull)white for the background
only, unless the foreground was white when it was a hard-coded black
for the background only, unless the foreground was white and the
background was black it was reverse video. In graphics mode, it was
always reverse video for the block cursor. Reverse video is worse,
especially over cutmarking regions, since cutmarking still uses simple
reverse video (nothing better is possible in text mode) and double
reverse video for the cursor gives normal video. Now, graphics mode
uses the same algorithm as the best case for text mode in all cases
for graphics mode. The hard-coded sequence { white, black, } for the
background is now { red, white, blue, } where the first 2 colors can
be configured. The blue color at the end is a sentinel which prevents
reverse video being used in most cases but breaks the compatibility
setting for white on black and black on white characters. This will
be fixed later. The compatibility setting is most needed for mono modes.
The previous commit to syscons.c changed sc_cnterm() to be more careful.
It followed null pointers in some cases. But sc_cnterm() has been
unreachable for 15+ years since changes for multiple consoles turned
off calls to the the cnterm destructor for all console drivers. Before
them, it was only called at boot time. So no driver with an attached
console has ever been unloadable and not even the non-console destructors
have been tested much.
These files are compiled in userland too, so we can't use sys/systm.h
and rely on CTASSERT. Switch to using _Static_assert instead.
MFC After: 3 days
Sponsored by: Netflix
card has to do PCIe transactions to complete the reset process, but
can't do them, per the PCIe spec, unless bus mastering is enabled.
Submitted by: Kinjal Patel
PR: 22166
terminal state for kernel console output.
r56043 in 2000 added many complications to support dynamic selection
of the terminal emulator using modules and the ioctl CONS_SETTERM.
This was never completed. There are still no modules, but it is easy
to restore the scterm and dumb emulators at compile time. Then
boot-time configuration for the preferred one doesn't work right, but
CONS_SETTERM almost works after fixing this bug. CONS_SETTERM only
switches the emulator for the user state, leaving the kernel state(s)
still using the boot-time emulator. The fix is especially important
when switching from sc to scteken, since the scteken state has pointers
in it.
Rename kernel_console_ts to sc_kts.
The previous update to the driver to 3.2.12-k changed the VF's API version
to 1.2, but did not let the VF fall back to 1.1 or 1.0 versions. So, this
patch tries 1.2 first, then the older versions in succession if that fails.
This should allow the VF driver to negotiate 1.1 and work with older PF
drivers, such as the one used in Amazon's EC2 service.
PR: 220872
Submitted by: Jeb Cramer <jeb.j.cramer@intel.com>
MFC after: 1 week
Sponsored by: Intel Corporation
Remote DMA over Converged Ethernet, RoCE, for the ConnectX-4 series of
PCI express network cards.
There is currently no user-space support and this driver only supports
kernel side non-routable RoCE V1. The krping kernel module can be used
to test this driver. Full user-space support including RoCE V2 will be
added as part of the ongoing upgrade to ibcore from Linux 4.9. Otherwise
this driver is feature equivalent to mlx4ib(4). The mlx5ib(4) kernel
module will only be built when WITH_OFED=YES is specified.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
sysctls to display stats, stats polled every 2 seconds
Modify QLA_LOCK()/QLA_UNLOCK() to not sleep after acquiring mtx_lock
Add support to turn OFF/ON error recovery following heartbeat failure for
debug purposes.
Set default max values to 32 Tx/Rx/SDS rings
MFC after:5 days
There was already a per-vty defaults field, but it was useless since it was
only initialized when propagating the global settings and thus no different
from the current global settings and not per-vty. The global defaults field
was also invariant after boot time, but not quite so useless.
Fix this by adding a second selection bit the the control flags of the
relevant ioctl(). vidcontrol doesn't support this yet. Setting either
default propagates the change to the current setting for the same level
and then to all lower levels.
Improve the 3-way escape sequence used by termcap to control the cursor.
The "normal" (ve) case has always used reset, so the user could set
it to anything, but since the reset is to a global value this is not
very useful, especially since the "very visible" (vs) case doesn't
reset but inconsistently forces to a blinking block. Change vs to
first reset and then XOR the blinking bit so that it is predictably
different from ve.
attribute field is curs_attr. The base field holds user data translated
in a reversible way and is needed because current field holds this in
an irreversible way for efficiency.
Factor out some common code for the reversible translation. This is
slightly simpler now, and much easier to expand.
Translate the magic flags value -1 to a single control flag internally
up front so other flags can be trusted later. This can be used for the
relevant ioctl() too.
Remove CONS_CURSOR_FLAGS which contained all the control flags. It was
unused and not useful. After adding more flags, there will be tests on
a couple at a time but never on them all. This API should have used this
to disallow unknown flags.
redundant initializations.
Hard-code base = 0, height = (approx. 1/8 of the boot-time font height)
in all cases, and remove the BIOS/MD support for setting these values.
This asks for an underline cursor sized for the boot-time font instead
of various less hard-coded but worse values. I used that think that
the x86 BIOS always gave the same values as the above hard-coding, but
on 1 of my systems it gives the wrong value of base = 1.
The remaining BIOS fields are shift_state and bell_pitch. These are now
consistently not explicitly reinitialized to 0. All sc_get_bios_value()
functions except x86's are now empty, and the only useful thing that x86
returns is shift_state. This really belongs in atkbdc, but heavier
use of the BIOS to read the more useful typematic rate has been removed
there. fb still makes much heavier use of the BIOS.
was aliased to a vt sequence, causing and fixing various bugs.
For syscons, this restores support for arg 2 which sets blinking block
too forcefully, and restores bugs for arg 0 and 1. Arg 2 is used for
vs in the cons25 entry in termcap, but I've never noticed an application
that uses this. The bugs involve replacing local settings by global
ones and need better handling of defaults to fix.
For vt, this requires moving the aliasing code from teken to vt where
it belongs. This sequences is very important for cons25 compatibility
in vt since it is used by the cons25 termcap entries for ve, vi and
vs. vt can't properly support vs for either cons25 or xterm since it
doesn't support blinking. For xterm, the termcap entry for vs asks
for something different using 12;25h instead of 25h.
Rename C25CURS for this to C25LCT and change its description to be closer
to echoing the old comment about it. CURS is too generic.
Fix missing syscons escape sequence for setting the global cursor shape
(and type). Only support this in syscons since vt can't emulate anything
in it.
It should toggle between 2 states, but it used a cut-down version of
support for a related 3-state syscons escape sequence and inherited
bugs from that. The usual misbehaviour was that hiding and showing
the cursor reset it to a global default.
Support for the 3-state sequence remains broken by aliasing to the 2-state
sequence. This works better but incompatibly for the 2 cases that it
supports.
