The OpenWRT AR8xxx switch support flushes the ATU (address translation
unit) after each port link 'up' status change. I've modified this to
just flush on any port transition.
Whilst here, bump the number of ports on the AR8327 to 6, rather than
the default of 5. It's DB120 specific; I'll go and make this configurable
later.
There's some debugging code in here still; I am still debugging whether
this is or isn't working fully.
Tested:
* DB120, AR9344 + AR8327 switch
Obtained from: OpenWRT
HAL methods.
This allows the AR8327 code to override it as appropriate.
Tested:
* DB120 - AR8327 and AR9340 on-board switch; only running 'etherswitchcfg'
to check configs. The actual VLAN programming wasn't tested.
a single port to setup.
This may end up later being used as part of some logic to program
the PHY for a single port, rather than having to reinitialise them
all at once.
Tested:
* DB120
* Do the hardware setup in the right order!
* Modify/improve the chip probe check so it can actually
probe the 7240/9340 directly (although it's not yet used..)
* Initialise and fetch the is_mii option
* Fix some debugging whilst I'm here.
This is enough to get things off the ground.
Tested:
* AR9344 SoC
depending upon the bootloader initialising it.
The aim is to eventually support a full switch set and reinitialisation
rather than relying on a consistent bootloader setup.
Remove the port flood config from arswitch.c, it's not yet used and
it's totally incorrect.
Whilst I'm here, also add in a comment describing why the full switch
reset is disabled.
Obtained from: Linux (OpenWRT) - Values
* Add in the AR724x support. It probes the same as an AR8216/AR8316, so
just add in a hint to force the probe success rather than auto-detecting
it.
* Add in the missing entries from conf/files, lacking in the previous
commit.
The register values and CPU port / mirror port initialisation value was
obtained from Linux OpenWRT ag71xx_ar7240.c.
The DELAY(1000) to let things settle is my local workaround. For some
reason, PHY4 doesn't seem to probe very reliably without it. It's quite
possible that we're missing some MDIO bus initialisation code in if_arge
for the AR724x case. As I dislike DELAY() workarounds in general, it's
definitely worth trying to figure out why this is the case.
Tested on: AP93 (AR7240) reference design
Obtained from: Linux OpenWRT
This is designed to support the very basic ethernet switch chip behaviour,
specifically:
* accessing switch register space;
* accessing per-PHY registers (for switches that actually expose PHYs);
* basic vlan group support, which applies for the rtl8366 driver but not
for the atheros switches.
This also includes initial support for:
* rtl8366rb support - which is a 10/100/1000 switch which supports
vlan groups;
* Initial Atheros AR8316 switch support - which is a 10/100/1000 switch
which supports an alternate vlan configuration (so the vlan group
methods are stubbed.)
The general idea here is that the switch driver may speak to a variety of
backend busses (mdio, i2c, spi, whatever) and expose:
* If applicable, one or more MDIO busses which ethernet interfaces can
then attach PHYs to via miiproxy/mdioproxy;
* exposes miibusses, one for each port at the moment, so ..
* .. a PHY can be exposed on each miibus, for each switch port, with all
of the existing MII/ifnet framework.
However:
* The ifnet is manually created for now, and it isn't linked into the
interface list, nor can you (currently) send/receive frames on this ifnet.
At some point in the future there may be _some_ support for this, for
switches with a multi-port, isolated mode.
* I'm still in the process of sorting out correct(er) locking.
TODO:
* ray's switch code in zrouter (zrouter.org) includes a much more developed
newbus API that covers the various switch methods, as well as a
capability API so drivers, the switch layer and the userland utility
can properly control the subset of supported features.
The plan is to sort that out later, once the rest of ray's switch drivers
are brought over and extended to export MII busses and PHYs.
Submitted by: Stefan Bethke <stb@lassitu.de>
Reviewed by: ray
