- Move tagged queueing control from ADA to ATA XPT. It allows to control
device command queue length correctly. First step to support < 32 tags.
- Limit queue for non-tagged devices by 2 slots for ahci(4) and siis(4).
- Implement quirk matching for ATA devices.
- Move xpt_schedule_dev_sendq() from header to source file.
- Move delayed queue shrinking to the more expected place - element freeing.
- Remove some SCSIsms in ATA.
- Rework timeout handling, to make it more graceful for devices sharing
controller port (with PMP). Wait for other commands completion/timeout
before initiating recovery.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Add workaround for ATI SB600/SB700 PMP probe related bug, to speedup boot.
On error, freeze device queue, to allow periph driver to do proper recovery.
Freeze SIM queue only in some cases, when it is needed to protect SIM.
Implement better command timeout detection logic for non-queued commands.
This fixes false positives when command with short timeout waiting for the
long one. For example, when hald tastes CD during burning process.
Read and clear SERR register on interrupt.
Immediately after clearing a pending callout that didn't make it due
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Turn off use of ATA_A_4BIT on modern hardware. This flag was already
obsoleted in 1996 by ATA-2, and crashes some modern hardware like some
revisions of the Serverworks K2 SATA controller. Even very ancient
hardware seems not to require it. In the unlikely event this causes
problems, the previous behavior can be re-enabled by defining
ATA_LEGACY_SUPPORT at the top of this file.
fault panic due to a failed bounce page allocation
during RX mbuf setup. The large demand on bounce pages
is due to the alignment requirement in the tag. This
restriction was removed in the ixgbe driver with no
ill effects and so is being removed here also.
Introduce new option BCE_JUMBO_HDRSPLIT that allows user to enable header
in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
into if_bce.c anyway. It is disabled by default.
Integrate lost interrupts patch from the old USB stack.
Some EHCI chips from VIA / ATI seem to trigger interrupts before writing back
the qTD status, or miss signalling occasionally under heavy load. If the host
machine is too fast, we can miss transaction completion - when we scan the
active list the transaction still seems to be active. This generally exhibits
itself as a umass stall that never recovers.
We work around this behaviour by setting up this callback after any softintr
that completes with transactions still pending, giving us another chance to
check for completion after the writeback has taken place
Submitted by: Alexander Nedotsuko
Initialize the whole message unit's DMA buffer to zero, this fixes a panic
during boot when ARC1200 is being used with certain motherboard models.
This commit brings the driver to the same state of vendor's 1.20.00.16
release. Many thanks to Areca for their continued support to FreeBSD.
This instant MFC was requested by re@ (kensmith) in preparation for
8.0-RC3.
Reported by: Jirka Mikulas <jiri mikulas com>
Submitted by: Erich Chen (Areca)
> While certain supported Symbios/LSI SCSI chips (532c896, 53c1000, 53c1010)
> do support 64bit addresses, the current SCRIPTS code supports only 32bit
> addresses causing data corruption for buffer addresses >4GB. This problem
> affects 64bit machines with more than 4GB RAM or amd64 with 4GB and
> memory hole remapping.
> Work-around this problem with a bus_dma tag that requests bounce-buffers
> for addresses >4GB. This causes some overhead, but given the maximum SCSI
> bus speed of 160MB/s compared, the effect should hardly be noticeable.
> The problem was reported by Mike Watters (mike at mwatters net) who also
> verified that this fix cures the problem.
>
> Since this change is a NOOP on systems with less than 4GB RAM and fixes
> data corruption (in RAM and on disk) on systems with more than 4GB, I hope
> that this change is accepted for 8.0.
Requested by: Stefan Esser (se at freebsd dot org)[1]
Reviewed by: jhb, scottl
[1] Stefan requested this be part of 8.0 but has been unavailable to do
the MFC since submitting the request. We want to get 8.0-RC3 started
so I'm doing the merges with re@ hat on.
Add support for different request block format used by Gen-IIe Marvell SATA.
This adds support for Marvell 6042/7042 chips and Adaptec 1430SA controller.
MFC r198718:
Allow newly added controllers to use full I/O sizes.
- Revert r191568 partially. Forcing AHCI mode by changing device subclass
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
Most of the pieces came from Marius- correct settings for channels
and resource management. The one piece missing was that you cannot
for SBus cards replace 32 bit operations with A64 operations- not
supported. This is an MFC of r198822.
It seems some 82559ER controllers do not support Rx checksum
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
When the timeout backoff hits the maximum value, leave it capped at the
maximum value rather than setting it to the result of a boolean expression
that is always true.
Increase AAC_CMD_TIMEOUT from 30s to 120s to help avoid spurious
"COMMAND 0x........ TIMEOUT AFTER .. SECONDS" messages. Any commands
that get truly stuck will still trigger the warning and the hardware
health check, just a little bit later.
Cleanup in r600_blit
- Don't bother to assign vb until we know we have enough space
- Add variables for sx2, sy2, dx2, dy2 so that these aren't
calculated over and over, also reduce chance of errors.
- Use switch to assign color/format
SVN r197174:
Make sure we never place the cursor outside the screen.
For some vague reason, it may be possible that scp->cursor_pos exceeds
scp->ysize * scp->xsize. This means that teken_set_cursor() may get
called with an invalid position. Just ignore the old cursor position in
this case.
Reported by: Paul B. Mahol <onemda gmail com>
SVN r198213:
Make lock devices work properly.
It turned out I did add the code to use the init state devices to set
the termios structure when opening the device, but it seems I totally
forgot to add the bits required to force the actual locking of flags
through the lock state devices.
Reported by: ru
SVN r198215, r198217:
Fix a typo in the jail(8) manpage.
Submitted by: Jille Timmermans <jille quis cx>
SVN r198216:
Fix qouting in a comment, to make it look more consistent
Submitted by: Jille Timmermans <jille quis cx>
SVN r198223:
Properly set the low watermarks when reducing the baud rate.
Now that buffers are deallocated lazily, we should not use
tty*q_getsize() to obtain the buffer size to calculate the low
watermarks. Doing this may cause the watermark to be placed outside the
typical buffer size.
This caused some regressions after my previous commit to the TTY code,
which allows pseudo-devices to resize the buffers as well.
Reported by: yongari, dougb
