- Make scan aborted by event restart immediately and infinitely.
- Improve handling of some loop events from firmware.
- Remove loop down timer, adding its functionality to scanner thread.
- Some more unification and simplification.
I added MYBEACON support a while ago to listen to beacons that are only
for your configured BSSID. For AR9380 and later NICs this results in
a lot less chip wakeups in station mode as it then only shows you beacons
that are destined to you.
However in IBSS mode you really do want to hear all beacons so you can do
IBSS merges. Oops.
So only use MYBEACON for STA + not-scanning, and just use BEACON for
the other modes it used to use BEACON for.
This doesn't completely fix IBSS merges though - there are still some
conditions to chase down and fix.
And expose vm_memattr_t of current mapping to consumers (as well as the
ability to change it to one of UC, WB, WC).
After short discussion with: jhb (but no review)
Sponsored by: EMC / Isilon Storage Division
- Add error handling for urtwn_(r88e_)read_rom() and
urtwn_efuse_*() functions.
- Remove code duplication between urtwn_efuse_read() and
urtwn_r88e_read_rom().
- Merge r88e_rom and (r92c_)rom structures
(only one of them can be used at the same time).
- Other minor fixes / improvements.
Tested with RTL8188EU, STA mode
(URTWN_DEBUG + USB_DEBUG, hw.usb.urtwn.debug=3, no visual differences).
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4253
Adds a new tunable, ntb.hw.b2b_mw_idx, which specifies the offset (from the
total number of memory windows) to use for register access on hardware with
the SDOORBELL_LOCKUP errata. The default is -1, i.e., the last memory
window.
We map BARs before the b2b_mw_idx is selected, so map them all as memory
windows initially. The register memory window should not be write-combined,
so we explicitly disable WC on the selected MW later.
This introduces a layer of abstraction between consumer memory window
indices, which exclude any exclusive errata-workaround BARs, and internal
memory window indices, which include such BARs. An internal routine,
ntb_user_mw_to_idx(), converts the former to the latter. Public APIs have
been updated to use this instead of assuming the exclusive workaround BAR is
the last available MW.
Sponsored by: EMC / Isilon Storage Division
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
bridges. Currently this includes information about what resources a
bridge decodes on the upstream side for use by downstream devices including
bus numbers, I/O port resources, and memory resources. Windows and bus
ranges are enumerated for both PCI-PCI bridges and PCI-CardBus bridges.
To simplify the implementation, all enumeration is done by reading the
appropriate config space registers directly rather than querying the
bridge driver in the kernel via new ioctls. This does result in a few
limitations.
First, an unimplemented window in a PCI-PCI bridge cannot be accurately
detected as accurate detection requires writing to the window base
register. That is not safe for pciconf(8). Instead, this assumes that
any window where both the base and limit read as all zeroes is
unimplemented.
Second, the PCI-PCI bridge driver in a tree has a few quirks for
PCI-PCI bridges that use subtractive decoding but do not indicate that
via the progif config register. The list of quirks is duplicated in
pciconf's source.
Reviewed by: imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D4171
Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.
Initiator mode tested with Qlogic 1080 adapter is still working fine.
While later firmware always registers for RSCN requests, older one does
it only in initiator mode. But in target mode there RSCN can be the only
way to detect gone intiator.
For those chips we are not receiving login events, adding initiators
based on ATIO requests. But there is no port ID in that structure, so
in fabric mode we have to explicitly fetch it from firmware to be able
to do normal scan after that.
Lower the payload data (IP) portion of the MTU from 0x10000 to
IP_MAXPACKET (0xFFFF) to avoid panicing the IP stack.
Sponsored by: EMC / Isilon Storage Division
This feature is disabled by default. To enable it, tune
hw.if_ntb.enable_xeon_watchdog to non-zero.
If enabled, writes an unused NTB register every second to demonstrate to
a hardware watchdog that the NTB device is still alive. Most machines
with NTB will not need this -- you know who you are.
Sponsored by: EMC / Isilon Storage Division
This change simplifies and unifies port adding/updating for loop and
fabric scanners. It also fixes problems with scanning restarts due to
concurrent port databases changes. It also fixes many cosmetic issues.
RX buffers from number of received packets.
Differential Revision: https://reviews.freebsd.org/D4178
Submitted by: Drew Gallatin <gallatin@freebsd.org>
Sponsored by: Mellanox Technologies
MFC after: 3 days
Setting sysctl dev....conf.hw_lro may fail if the net device lro is
turned off. Due to the nature of our sysctl handler we need to set the
values back to 0 and issue an error.
Differential Revision: https://reviews.freebsd.org/D4177
Submitted by: Shahar Klein <shahark@mellanox.com>
Sponsored by: Mellanox Technologies
MFC after: 3 days
Discard the unused rx_free_q. Instead, reuse inputed packets by putting
them back on the *pend* queue after reinitialization.
If tx or rx handlers are unavailable, free mbufs rather than leaking
them.
With this change, if_ntb can receive more than 100
(NTB_QP_DEF_NUM_ENTRIES) packets.
Sponsored by: EMC / Isilon Storage Division
32-bit BARs can only address memory mapped in the low 32 bits of
physical RAM. Expose this as a 'plimit' out parameter from
ntb_mw_get_range().
Fix if_ntb to allocate memory within this limit.
Sponsored by: EMC / Isilon Storage Division
Sometimes they'll read spurious values (observed: 0xc on Broadwell-DE),
failing link negotiation.
Discussed with: Dave Jiang, Allen Hubbe
Sponsored by: EMC / Isilon Storage Division
The tunable 'hw.ntb.enable_writecombine' may be set to zero to
administratively disable write combining the mapped NTB region.
Sponsored by: EMC / Isilon Storage Division
Use bus_space_write instead of (non-volatile) C pointer writes via an
iowrite32() shim in the same places as the Dual BSD/GPL Linux driver.
Update some types to fixed 32-bit sizes.
Sponsored by: EMC / Isilon Storage Division
Current Xen resume code clears all pending bitmap IPIs on resume, which is
not correct. Instead re-inject bitmap IPI vectors on resume to all CPUs in
order to acknowledge any pending bitmap IPIs.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
Modern cards in most cases operate abstract port handles, that have no
any relation to real loop IDs. Leave loopid used only where it really
goes about local loop IDs.
While there, fix few more cases where LUNs were still printed in decimal.
It turns out on a 16550 w/ a 25MHz SoC reference clock you get a little
over 3% error at 115200 baud, which causes this to fail.
Just .. cope. Things cope these days.
Default to 30 (3.0%) as before, but allow UART_DEV_TOLERANCE_PCT to be
set at build time to change that.
