The new bcache code does not know the size of the disk, and therefore may attempt to read past the end of the disk while trying to fill its read-ahead cache.
This is usually not an issue, it fails gracefully on all of my machines, but some BIOSes seem to retry the reads for up to 30 seconds each, resulting in a long stall during boot
Submitted by: Toomas Soome <tsoome@me.com>
Reviewed by: jhb, np
Differential Revision: https://reviews.freebsd.org/D6109
Avoid logging inconsistency for the /dev/mem device at all. The driver
leaves memattr intact, and the corrective action in the device pager
handles it right.
In the logged warning, name the driver we blame, and show memory
attributes values.
Reported and tested by: pho
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D6149
driver is (or behaves identically to) /dev/mem. Remove the D_MEM flag
from random drivers.
Note that currently the D_MEM flag does not affect any behaviour, but
this going to change in the next commit.
Noted and reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-Differential revision: https://reviews.freebsd.org/D6149
The Linux driver sets the rate_n_flags regardless of whether it's being
sent using firmware rate control or local rate control. This includes
the antenna configuration.
Thanks to Kyle Evans <kevans91@ksu.edu> for pointing this out to me
and doing some investigation/testing on his end.
Tested:
* Intel 7260 STA, 2G and 5G networks
64-bit MIPS, use superpage rather than physical-segment constants, or
we may improperly fail to apply suitable alignment -- yet still allow
mmap() to appear to succeed.
Reviewed by: sson
MFC after: 1 week
Sponsored by: DARPA, AFRL
implementations. Early in the boot the kernel will use an approximate,
however after the timer has been probed it will switch to a more accurate
implementation.
Reviewed by: manu
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5762
This is currently only a code change without any functional
change. But this allows to set the remote encapsulation port
in a more detailed way, which will be provided in a follow-up
commit.
MFC after: 1 week
FDT overlays is de-facto standard for describing expansion boards like
Beaglebone capes or Raspberry Pi shields. The ides is to have basic
DTB for base board and overlays DTB for shields/capes and to construct
final DTB either using human-readable configuration or some
self-discovery mechanism. I believe this approach can also be expanded
to support dynamically loadable FPGA bitstreams on systems like
Zedboard/Zybo.
Overlaying process is simmilar to executable link process for
binaries: each DTB has "exported" symbols and "undefined" symbols, the
latter are resolved using information for the former obtained from
base DTB or one of the overlays applied earlier (more rare case).
This symbols information is not generated by standard dtc that FreeBSD
has in base system, patched[1] version required to produces
overlay-compatible blobs. So although DTB files generated by
buildkernel do not support overlays there are enough
vendor/community-provided DTB blobs ciruclating around to justify
committing this change to ubldr.
This commit introduces handler for "fdt_overlays" variable that can be
defined either as a loader env variable or U-Boot env variable.
fdt_overlays is comma-separated list of .dtbo files located in
/boot/dtb/ directory along with base .dtb. ubldr loads files and
applies them one-by-one to base .dtb and then passes result blob to
the kernel.
[1] dd6a0533e8
Differential Revision: https://reviews.freebsd.org/D3180
clear vd->vdev_tsd in vdev_geom_close_locked instead of vdev_geom_detach.
In the latter function, it would fail to happen in certain circumstances
where cp->private was unset. Ideally, the latter should never happen, but
it can happen when vdev open fails, or where spares are involved.
MFC after: 4 weeks
X-MFC-With: 298786
Sponsored by: Spectra Logic Corp
This change adds few methods for net80211 channel table setup:
- ieee80211_add_channel()
- ieee80211_add_channel_ht40()
(primarily for drivers, that parse EEPROM to get channel list -
they will allow to hide implementation details).
- ieee80211_add_channel_list_2ghz()
- ieee80211_add_channel_list_5ghz()
(mostly as a replacement for ieee80211_init_channels() - they will allow
to specify non-default channel list; may be used in ic_getradiocaps()).
Tested with wpi(4) (add_channel) and rum(4) (add_channel_list_2ghz).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6124
Build and install the subr_unit test program originally written by phk, and
run it with the other ATF tests.
tests/sys/kern/Makefile
* Build and install the subr_unit test as a plain test
sys/kern/subr_unit.c
* Reduce the default number of repetitions from 100 to 1, and add a
command-line parser to override it.
* Don't be so noisy by default
* Fix an include problem for the test build
Reviewed by: ngie
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D6038
Split ADC driver in two halves: ADC(analog ot digital) and
TSC(touchscreen). Touchscreen driver is fully functional
up to the point of reporting samples. This part will be added
once FreeBSD has API for touchscreen.
Tested on: Beaglebone Black + 4DCAPE-43T
Reviewed by: loos
Differential Revision: https://reviews.freebsd.org/D5847
