Pyun YongHyeon cb2ed75f7e Add check for fiber mode for BCM5714 PHY. This PHY supports both ... copper and fiber interfaces over GMII so an explicit check is necessary to know whether it was configured for fiber interface. This change make BCM5715S work. Tested by: olli MFC after: 1 week		2010-01-14 19:14:24 +00:00
..
acphy.c
acphyreg.h
amphy.c
amphyreg.h
atphy.c	Use auto-negotiation for manual media type selection. This fixes	2008-10-25 06:39:17 +00:00
atphyreg.h
axphy.c	New PHY driver for the internal PHY found in the AX88790. There's a	2009-03-30 16:01:09 +00:00
axphyreg.h	New PHY driver for the internal PHY found in the AX88790. There's a	2009-03-30 16:01:09 +00:00
bmtphy.c
bmtphyreg.h
brgphy.c	Add check for fiber mode for BCM5714 PHY. This PHY supports both	2010-01-14 19:14:24 +00:00
brgphyreg.h
ciphy.c	Correct PHY description and OUI of VSC8211. Previously VSC8211 was	2008-10-23 01:27:15 +00:00
ciphyreg.h
e1000phy.c	Add hack to pass controller specific information to phy driver.	2009-09-28 21:03:28 +00:00
e1000phyreg.h	Add hack to pass controller specific information to phy driver.	2009-09-28 21:03:28 +00:00
exphy.c
gentbi.c
icsphy.c
icsphyreg.h
inphy.c
inphyreg.h
ip1000phy.c	Make sure to enable Next Page bit for IP1001. Otherwise the PHY	2009-12-18 21:57:51 +00:00
ip1000phyreg.h	For IP1001 PHYs, read auto-negotiation advertisement register to	2009-03-09 08:17:46 +00:00
jmphy.c
jmphyreg.h
lxtphy.c
lxtphyreg.h
mii.c	Revert bogusly committed file.	2008-08-23 07:46:58 +00:00
mii.h
mii_physubr.c
miibus_if.m
miidevs	Add BCM5754 PHY id that is found on Dell Studio XPS 16.	2010-01-14 00:36:49 +00:00
miivar.h
mlphy.c	Move the code that looks for the companion phy to a subroutine to make	2008-08-23 15:50:18 +00:00
nsgphy.c	- Also probe DP83865, which is an is an ultra low power version	2009-06-13 23:27:04 +00:00
nsgphyreg.h
nsphy.c
nsphyreg.h
nsphyter.c
nsphyterreg.h
pnaphy.c
qsphy.c
qsphyreg.h
rgephy.c	Fix a copy/paste error	2008-08-06 07:52:59 +00:00
rgephyreg.h	Add RTL8211C(L) support.	2008-07-02 08:10:18 +00:00
rlphy.c
rlswitch.c
ruephy.c
ruephyreg.h
smcphy.c
tdkphy.c	cardbus -> CardBus	2010-01-03 23:31:58 +00:00
tdkphyreg.h
tlphy.c	It turns out that my analysis of the error handling here was wrong.	2008-08-23 15:29:28 +00:00
tlphyreg.h
truephy.c	Renamed the FRAMELEN macro to TRUEPHY_FRAMELEN as for powerpc	2008-11-28 23:44:13 +00:00
truephyreg.h
ukphy.c
ukphy_subr.c
xmphy.c
xmphyreg.h