Adrian Chadd 2fd9aabb1b Fix beacon transmission after a channel set. ... The DFS code was tickling the channel set directly whilst going through the state RUN -> CSA -> RUN. This only changed the channel; it didn't go via ath_reset(). However in this driver, a channel change always causes a chip reset, which resets the beacon timer configuration and interrupt setup. This meant that data would go out but as the beacon timers never fired, beacons would never be queued. The confusing part is that sometimes the state transition was RUN -> SCAN -> CAC -> RUN (with CSA being in there sometimes); going via SCAN would clear sc_beacons and thus the transition to RUN would reprogram beacon transmission. In case someone tries debugging why suspending a device currently beaconing (versus just RX'ing beacons which is what occurs in STA mode), add a silly comment which should hopefully land them at this commit message. The call to ath_hal_reset() will be clearing the beacon config and it may not be always reset.		2011-06-26 13:53:24 +00:00
..
ath_dfs/null	Commit radar detection changes missed by my previous commit.	2011-06-04 08:24:58 +00:00
ath_hal	Small fix to bring the non-debug definitions of HALDEBUG/HALDEBUG_G in line	2011-06-24 23:59:14 +00:00
ath_rate	Modify the sample rate control algorithm to only select/sample HT	2011-05-18 07:20:30 +00:00
ah_osdep.c	Commit missing piece from a couple days ago - re-add ath_hal_debug.	2011-06-25 00:34:40 +00:00
ah_osdep.h	Fix AR5416 and later parts when building with AH_DEBUG or similar defined:	2009-07-06 20:51:54 +00:00
if_ath.c	Fix beacon transmission after a channel set.	2011-06-26 13:53:24 +00:00
if_ath_ahb.c	Fix ath_ahb(4) bus attach and eeprom error handling.	2011-06-13 04:31:57 +00:00
if_ath_debug.c	Break out the debug macros from if_ath.c into if_ath_debug.[ch] .	2011-01-29 05:08:21 +00:00
if_ath_debug.h	Break out the debug macros from if_ath.c into if_ath_debug.[ch] .	2011-01-29 05:08:21 +00:00
if_ath_keycache.c	Break the keycache management functions out into if_ath_keycache.c .	2011-03-02 17:19:54 +00:00
if_ath_keycache.h	Break the keycache management functions out into if_ath_keycache.c .	2011-03-02 17:19:54 +00:00
if_ath_misc.h	Migrate the sysctl related routines (statistics, debugging, etc) out of	2011-03-02 16:03:19 +00:00
if_ath_pci.c	Break out the ath PCI logic into a separate device/module.	2011-03-31 08:07:13 +00:00
if_ath_sysctl.c	Break out most of the HAL related tweaks into a per-HAL instance,	2011-06-23 02:38:36 +00:00
if_ath_sysctl.h	Break out most of the HAL related tweaks into a per-HAL instance,	2011-06-23 02:38:36 +00:00
if_ath_tx.c	Add in HT protection but disable it by default.	2011-03-28 11:48:49 +00:00
if_ath_tx.h	Migrate the TX path code out of if_ath and into a separate source file.	2011-01-29 11:35:23 +00:00
if_ath_tx_ht.c	Enable setting the short-GI bit when TX'ing HT rates but only if the	2011-05-30 15:06:57 +00:00
if_ath_tx_ht.h	The current code used the fields in ath_set11nratescenario() . Use them	2011-02-12 02:14:19 +00:00
if_athdfs.h	A few changes to make radar detection implementable in a hal_dfs/	2011-06-04 04:14:59 +00:00
if_athioctl.h	* Add some more TX descriptor error counters; this'll be helpful when	2011-05-15 15:54:34 +00:00
if_athrate.h	Add a new method to the rate control modules which extract out the	2011-02-01 08:10:18 +00:00
if_athvar.h	Flesh out a new HAL method to fetch the radar PHY error frame information.	2011-06-07 09:03:28 +00:00