Adrian Chadd e69db8df7d Improve performance of the Sample rate algorithm on 802.11n networks. ... * Don't treat high percentage failures as "sucessive failures" - high MCS rates are very picky and will quite happily "fade" from low to high failure % and back again within a few seconds. If they really don't work, the aggregate will just plain fail. * Only sample MCS rates +/- 3 from the current MCS. Sample will back off quite quickly, so there's no need to sample _all_ MCS rates between a high MCS rate and MCS0; there may be a lot of them. * Modify the smoothing rate to be 75% rather than 95% - it's more adaptive but it comes with a cost of being slightly less stable at times. A per-node, hysterisis behaviour would be nicer.		2012-09-17 01:09:17 +00:00
..
ath_dfs/null	Disable strong signal diversity when enabling radar pulse detection	2012-09-02 05:01:10 +00:00
ath_hal	Don't use AR_PHY_MODE to setup half/quarter rate.	2012-09-13 18:24:13 +00:00
ath_rate	Improve performance of the Sample rate algorithm on 802.11n networks.	2012-09-17 01:09:17 +00:00
ah_osdep.c	Fix the HAL debugging to only use one bit to mark a message as unmaskable.	2012-07-01 02:34:32 +00:00
ah_osdep.h	Migrate the ath_hal_filltxdesc() API to take a list of buffer/seglen values.	2012-08-05 10:12:27 +00:00
if_ath.c	Remove TDMA #define entries from if_ath.c; they now exist in if_ath_tdma.h.	2012-09-09 04:53:10 +00:00
if_ath_ahb.c	Flesh out a new DMA map for the EDMA TX completion status, as well	2012-07-23 02:49:25 +00:00
if_ath_beacon.c	Extend the beacon code slightly to support AP mode beaconing for the	2012-08-11 23:26:19 +00:00
if_ath_beacon.h	Extend the beacon code slightly to support AP mode beaconing for the	2012-08-11 23:26:19 +00:00
if_ath_debug.c	Only print the descriptor contents!	2012-08-27 23:27:41 +00:00
if_ath_debug.h	Map ATH_KTR_* to 0 when ATH_DEBUG is not defined. This effectively NOPs	2012-07-11 12:10:13 +00:00
if_ath_keycache.c	Add a 'vap' to ath_keyset().	2011-11-08 19:25:52 +00:00
if_ath_keycache.h	Add a 'vap' to ath_keyset().	2011-11-08 19:25:52 +00:00
if_ath_led.c	Bring over the initial 802.11n bluetooth coexistence support code.	2012-06-26 22:16:53 +00:00
if_ath_led.h	Refactor out the software LED config code into a common function, called	2011-12-26 05:46:22 +00:00
if_ath_misc.h	Break out the TX completion code into a separate function, so it can be	2012-08-14 22:32:20 +00:00
if_ath_pci.c	Flesh out a new DMA map for the EDMA TX completion status, as well	2012-07-23 02:49:25 +00:00
if_ath_rx.c	Remove extra debugging - there's no longer any need.	2012-08-29 00:53:41 +00:00
if_ath_rx.h	Convert sc_rxpending to a per-EDMA queue, and use that for the legacy code.	2012-07-10 00:02:19 +00:00
if_ath_rx_edma.c	Remove - not needed.	2012-08-29 00:53:58 +00:00
if_ath_rx_edma.h	Begin abstracting out the RX path in preparation for RX EDMA support.	2012-07-03 06:59:12 +00:00
if_ath_sysctl.c	Dump out the TX FIFO depth.	2012-08-14 22:34:22 +00:00
if_ath_sysctl.h	Break out most of the HAL related tweaks into a per-HAL instance,	2011-06-23 02:38:36 +00:00
if_ath_tdma.c	Migrate the TDMA management functions out of if_ath.c into if_ath_tdma.c.	2012-05-20 02:49:42 +00:00
if_ath_tdma.h	Migrate the TDMA management functions out of if_ath.c into if_ath_tdma.c.	2012-05-20 02:49:42 +00:00
if_ath_tsf.h	Migrate the bulk of the RX routines out from if_ath.c to if_ath_rx.[ch].	2012-05-20 02:05:10 +00:00
if_ath_tx.c	Clear the correct descriptor when going through the chained together	2012-09-11 04:11:42 +00:00
if_ath_tx.h	Revert the ath_tx_draintxq() method, and instead teach it the minimum	2012-08-12 00:46:15 +00:00
if_ath_tx_edma.c	Initialise an uninitialised variable.	2012-08-21 16:44:25 +00:00
if_ath_tx_edma.h	Begin separating out the TX DMA setup in preparation for TX EDMA support.	2012-07-23 03:52:18 +00:00
if_ath_tx_ht.c	Correctly mask out the RTS/CTS flags when forming aggregates.	2012-09-08 02:56:09 +00:00
if_ath_tx_ht.h	Introduce TX aggregation and software TX queue management	2011-11-08 22:43:13 +00:00
if_athdfs.h	Change the ath_dfs_process_phy_err() method to take an mbuf rather than	2012-06-24 08:09:06 +00:00
if_athioctl.h	Placeholder ioctl for an upcoming rate control statistics API change.	2012-07-31 02:18:10 +00:00
if_athrate.h	Create an ioctl API for fetching the current rate control information.	2012-07-20 01:27:20 +00:00
if_athvar.h	Add an accessor macro for getting access to the default DFS parameters.	2012-08-24 17:37:12 +00:00