multi-firmware support. This patch just changes
numerous names in the driver sources and is actually
nilpotent. This has been checked by comparing the
generated assembly code.
The names that have been changed are related to the
script names. They were named `script' and `script H'.
They are now named respectively `script A' and
`script B'.
before I rip out the scheduler - whilst v. nice 'n all, it is doing the
wrong job. We need something that sends commands to the card atomically
so dhcp etc. works right.
I've renamed and moved a lot of the scheduler code so that it is all
in one place and all starts with ray_cmd_
ray_stop has some debugging crap left in - to be deleted rsn
support. Changes are rather simplifications of the SCRIPTS
interface (prior to complexifying it again;) ), dead code
removes and comment fixes.
Code removed:
- Handling of kernel variables referenced from SCRIPTS.
- Handling of selection without ATN.
Slightly rewritten:
- Handling of illegal phase (4/5) and data overrun conditions.
Simplifications:
- Extended error flag and bits now only set from the C code.
- Move the extended error status (xerr_status) and nego
status (nego_status) outside the data structure accessed
by SCRIPTS (struct dsb).
- Get rid of the script status field (scr_st).
- Only patch SCR_NO_OP SCRIPTS instructions to adapt SCRIPTS
to actual chip capabilities.
Cosmetic changes:
- Miscellaneous comments in SCRIPTS.
- FreeBSD_4_Bus define replaced by FreeBSD_Bus_Io_Abstraction.
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
incorrectly attach itself to ThunderLAN adapters which happen to have
a PHY who's model number happens out to be 0.
Problem reported by: Peter L. Thomas <Pete@painless-computing.com>
(which is actually a CATC Netmate).
Gee. I don't know why people make such a fuss over supporting USB ethernet
NICs. This is easier than collecting graft.
in attach.
- Change a EISA_CHANNEL_CLEAR to EISA_CHANNEL_BUSY in ida_v1_submit().
This may fix the problem with EISA IDA adapters though we have not heard
back from testers yet.
Reviewed by: jlemon
o Eliminate cross calls between the devices. Instead move to using the
newbus messaging system. Added three new card calls: attach_card,
detach_card, get_type.
o Eliminate interrupt routine in pccard we never use.
o Move from deactivate to detach for removing cards.
o Start mapping CIS memory, but it is broken and causes panics. At least
it is closer to working than before.
o Eliminate struct device everywhere. It was bogus.
o Initialize softc for pccard device so we have valid pointers to
ourselves.
o Implement routine to find the pcic ivar for a child device of the pccard so
we can use it to talk to the pcic hardware.
o Lots of minor tiding up.
This version now panics when we try to read the CIS. The next batch
of work to make this work is what was outlined in my posting to mobile
about resource allocation and such.
- implement user-initiated background drive rebuild
- implement user-initiated background consistency check
- log controller-initiated background rebuild/check operations
Try to fix the elusive "invalid log operation" bug, and panic if we do
hit this one in the hopes of getting better information.
Tidy up diagnostic messages.
Try to use disk_create/disk_destroy correctly. This isn't working
properly yet, but it's not clear whose fault that is.
robust enough to work with dhcp. Essentially the driver returns to userland
before certain commands have been completed by the card. I'm trying to
work out the best way to fix this. There are very minor functional changes,
most of this is debugging.
Rework of debugging so a bit mask is used and re-allocation around the place.
Tried to protect ray_init with a tsleep until the network has been joined. I think this is only a partial fix as we also update the mcast and promisc
values.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Add support for ISA based DPT adapters (this doesn't quite work yet).
- Sync dpt_eisa.c with my local copy.
- Simplify how EISA IDs are matched.
- Prototype.
- Formatting nits.
- Conform to how I do things in dpt_pci.c/dpt_isa.c.
- Modify dpt_scsi.c:dpt_alloc() to DTRT with newbus.
- Add some comments to dpt_scsi.c:dpt_pio_get_conf().
- Add additional check to dpt_scsi.c:dpt_get_conf().
- Add some useful error messages to dpt_scsi.c:dpt_init().
request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
connected during boot and the vpo module is in the kernel/loaded.
In the case where the module is loaded at some later stage with kldload,
the CAM bus is now rescanned as well.
- The driver now uses bus_space() and runs on NetBSD 1.4.2
Submitted by Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
- Remove startup quirks for video and vbi capture for PAL users.
PAL TV users can now run FXTV and Alevt in any order.
- Add support for cable channels >100
Submitted by Scott Presnell <srp@zgi.com>
- New MSP3410/3415 setup code added. This is experimental.
Please set the sysctl hw.bt848.slow_msp_audio to 1 for this.
Submitted by Frank Nobis<fn@radio-do.de>
Pass sc->dev rather than a bogusly cast pccard_softc *sc.
This allows us to insert and remove cards w/o panicing the kernel.
However, the cis isn't mapped in, so the pccard_scan_cis function
fails.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
introduced in FreeBSD-4.0. The driver is now full up-to-date
with regards to the current kernel interfaces.
Another significant change in this driver version applies
to the checking of the data direction. The driver is now
able to check against the expected data direction in any
circumstance and will not hang either if direction is wrong
at the start of the IO, or if for some weird reason,
the device changes to the wrong direction during the IO.
This driver version is still usable under FreeBSD 3.2/3.3,
since it only requires CAM, other kernel interface dependencies
being #if'ed in the sources according to kernel version.
But, in order to use the driver under those early kernel
versions, user has to move the driver sources by hand and make
appropriate tiny changes to let the kernel know about the driver.
Other changes:
- Remove the debugging stuff for WSR bit.
- Get rid of some warnings about volatile being discarded.
which think they know the IntelliMouse 4-byte packet and believe,
wrongly, that any other protocols use 3-byte packets.
- Update a couple of comment lines for A4 Tech mice.
conf/files
i don't seem to be clearing the cache right resulting in a short initial
burst of noise, despite doing the same as creative and alsa. i'm committing
now so more eyes can pore over the code.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
doesn't support winmodems, softmodems, hcf or any other modem that
relies on the host to do any sort of soft control for any aspect of
the modem's function. There are two modems known to work:
3COM FaxModem PCI.
ActionTec 56k VoiceMessaging PCI Modem
and the following modem might work
Multitech PCI FaxModem (not sure about this)
and the serial pci cards might work too. I have neither these
hardware items so I can't add support for them.
- Add periodic status monitoring routine. Currently just detects
lost commands, further functionality pending data from AMI.
Add some new commands states; WEDGED (never coming back) and
LATE (for when a command that wasmarked as WEDGED comes bacj,
- Remove a number of redundant efforts to poll the card for completed
commands. This is what interrupt handlers are for.
- Limit the maximum number of outstanding I/O transactions. It seems
that some controllers report more than they can really handle,
and exceding this limit can cause the controller to lock up.
- Don't use 'wait' mode for anything where the controller might not
be able to generate interrupts. (Keep the 'wait' mode though sa it
will become useful when we start taking userspace commands.
- Use a similar atomic locking trategy to the Mylex driver to prevent
some reentrancy problems.
- Correctly calculate the block count for non-whoile-bloch transfers
(actually illegal).
- Use the dsik device's si_drv1 field instead of b_driver1 in the
buf struct to pass the driver identifier arond.
- Rewrite amr_start and amr_done() along the lines of the Mylex driver
in order to improve robustnes.
- Always force the PCI busmaster bit on.
- Move dev/aic/aic_isa.c entry from conf/files to conf/files.MACHINE
because PC-98 uses different file.
Submitted by: nyan and IMAI Takeshi <take-i@ceres.dti.ne.jp>
fe_read_eeprom_rex() and fe_init_rex(). These functions should be
useful for REX-5580 series (for PC-AT). But they are included in
`#ifdef PC98' to avoid warnings by unused static functions. If you
try to support REX-5580, please be aware of these functions.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
rewrite ess mixer to use native registers
rewrite play/rec code to use more accurate timer when available
add code to use audio2 for playback, but disable it as no irqs are generated
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
address size that is different than the standard 6bits. This fixes
support for the Compaq NC3121 card, certain newer Intel Pro/100+
cards, and should also fix integrated NICs on SuperMicro and Compaq
motherboards.
The auto-sizing algorithm was taken from NetBSD (thanks!), which I
think got it from Linux originally.
Thanks also to Andrew Sparrow <spadger@best.com> and Joe Moore
<jomor@ahpcns.com> for supplying me with unworking Compaq and Intel
cards to develop and test the fixes with.
set properly in the struct buf with vinum:
Fix locations where B_READ was cleared in the old code but
b.b_iocmd wasn't set to BIO_WRITE
Fix propogation of b_iocmd
Correct comments to reflect reality
Don't compare b_flags with BIO_READ, it's in b_iocmd.
Submitted by: Bernd Walter <ticso@cicely.de>
Remove RF_PCCARD_ATTR in anticipation of removing it from sys/rman.h
Add interface for setting "attributes" of pccard/cardbus devices.
Minor formatting nits.
timeout closer to the 1-second value that AMI use in their Linux
driver, and mark the mailbox structures as volatile so that gcc
doesn't over-optimise access to them.
This should fix the "controller wedged" bug.
Submitted by: Brian Dean <brdean@unx.sas.com>
* add a callback for initialising the mixer interface
* support ac97 2.1 variable rate audio feature
fix ac97-using drivers for the above
add suspend/resume support for neomagic
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
substitute BUF_WRITE(foo) for VOP_BWRITE(foo->b_vp, foo)
substitute BUF_STRATEGY(foo) for VOP_STRATEGY(foo->b_vp, foo)
This patch is machine generated except for the ccd.c and buf.h parts.
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
too many, so I removed the checks for the valid OUIs. We already do a
checksum of the entire ethernet address, so extra checking against the
OUI shouldn't be needed.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
prevent a page fault if the card is ejected while BPF is in use. This
could happen if DHCP or tcpdump was in use on that interface during
ejection. Other drivers may also require this modification.
Reviewed by: wes
negotiation features (DT, ULTRA2, ULTRA, FAST). The offsets
where not properly updated when the DT entry was added and so
the driver could attempt to negotiate a speed faster than that
supported by the target device or even requested by the user
via SCSI-Select settings. *
o Update the target mode incoming command queue kernel index value
ever 128 commands instead of 32. This means that the kernel will
always try to keep its index (as seen on the card - the kernel may
actually have cleared more space) 128 commands ahead of where the
sequencer is adding entries.
o Use the HS_MAILBOX register instead of the KERNEL_TQINPOS location
in SRAM to indicate the kernel's target queue possition on Ultra2
cards. This avoids the "pause bug" on these cards and also turns
out to be much more efficient.
o When enabling or disabling a particular target id for target mode,
make sure that the taret id in the SCSIID register does not
reference an ID that is not to receive target selections. This
is only an issue on chips that support the multiple target id
feature where the value in SCSIID will still affect selection
behavior regardless of the values in the target id bit field
registers.
o Remove some target mode debugging printfs.
o Make sure that the sense length reported in ATIO commands is
always zero. This driver does not, yet, report HBA generated
sense information for accepted commands.
o Honor the CAM_TIME_INFINITY and CAM_TIME_DEFAULT values for
the CCB timeout field.
o Make the driver compile with AHC_DEBUG again.
* Noticed by: Andrew Gallatin<gallatin@cs.duke.edu>
-current. It doesn't work yet as stable as the 3.x/PAO version of the
driver does, however, i get occasional `FDC direction bit not set' and
other weird messages, but it basically works at least.
The old (defunct) #ifdef FDC_YE stuff has been eliminated completely
now, PCMCIA-FDC specific functions have been implemented differently
where needed.
Unfortunately, due to the fact that the traditional PeeCee FDC with
its funny non-contiguous register space (one register for WD1003
harddisk controllers is interleaved into the FDC register set), and
Peter's subsequent changes involving two different bus space handles
for normal FDCs, the changes required for the Y-E stuff are more
complex than i'd love them to be. I've done my best to keep the logic
for normal FDCs intact.
Since the Y-E FDC seems to lose interrupts after a FDC reset
sometimes, i've also replaced the timeout logic in fd_turnoff() to
generate an artificial pseudo interrupt in case of a timeout while the
drive has still outstanding transfers waiting. This avoids the total
starvation of the driver that could be observed with highly damaged
media under 3.x/PAO. This part of the patch has been revied by bde
previously.
I've fixed a number of occasions where previous commits have been
missing the encapuslation of ISA DMA related functions inside
FDC_NODMA checks.
I've added one call to SET_BCDR() during preparation of the format
floppy operation. Floppy formatting has been totally broken before in
3.x/PAO (garbage ID fields have been written to the medium, causing
`wrong cylinder' errors upon media reading). This is just black
magic, i don't have the slightes idea _why_ this needs to be but just
copied over the hack that has been used by the PAO folks in the normal
read/write case anyway.
The entired device_busy() stuff seems to be pointless to me. In any
case, i had to add device_unbusy() calls symmetrical to the
device_busy() calls, otherwise the PCMCIA floppy driver could never be
deactivated. (As it used to be, it caused a `mark the device busier
and busier' situation.) IMHO, all block device drivers should be
marked busy based on active buffers still waiting for the driver, so
the device_unbusy() calls should probably go to biodone(). Only one
other driver (whose name escapes me at the moment) uses device_busy()
calls at all, so i question the value of all this...
I think this entire `device busy' logic simply doesn't fit for PCMCIA
&al. It cannot be the decision of some piece of kernel software to
declare a device `busy by now, you can't remove it', when the actual
physical power of removing it is the user pulling the card. The
kernel simply has to cope with the removal, however busy the device
might have been by the time of the removal, period. Perhaps a force
flag needs to be added?
Upon inserting the card a second time, i get:
WARNING: "fd" is usurping "fd"'s cdevsw[]
WARNING: "fd" is usurping "fd"'s bmaj
I suspect this is related to the XXX comment at the call to
cdevsw_add(). Does anybody know what the correct way is to cleanup
this?
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
- Properly keep track of resources (I/O ports and irq).
- Use bus_space_read/write() to access the ports.
- Add PnP IDs.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
this version include:
- Support for version 2.x firmware (2.42 or later recommended). This
means we are the only open-source driver supporting these adapters.
This code has only been tested on a Digital KZPCA adapter in an Alpha
system, but is believed to be correct. NOTE: EISA adapters are not
yet supported.
- Support the BIOS/Firmware initialisation handshake protocol. This
allows the driver to bring the card up to operational state even if
the BIOS can't be run (eg. if it's an x86 BIOS in an Alpha system).
- A working command pasthrough interface. This allows a user-space
configuration tool (under development) to issue arbitrary commands
to the controller or to devices in the system.
platform we're running on so we know how many bits to reserve at the top
end for the 'hose' value. It turns out that there's *just* enough room
to support all possible hoses on TurboLaser.
Reviewed by: gallatin@freebsd.org, dfr@free3bsd.org
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
rest of the code in (so changing media actually works.)
Add a few more register definitions for use with this and other new code.
Print a few details in the probe message; this should be useful in
bug reports and such but should not add to the clutter.
* i needed it anyway
* remove startccs and startcmd - done
* as those were used for the NetBSD start timeout
* multicast - done but UNTESTED
* I don't have the ability/facilty to test this
* rxlevel - done
* stats reported via raycontrol
* getparams ioctl - done
* reported via raycontrol
* start_join_done needs a restart in download_done - done
* now use netbsd style start up
removed spare timerh
implemented start_assoc in ray_ccs_done
bit more knfing
we get the com address. If so, we go ahead and return. Bruce thinks
there's a bug in the pccard layer that it terminates devices with
extreme prejustice rather than letting them deside for themselves when
to terminate (and he's likely right). This fix doesn't change that,
but instead works around it by checking for NULL pointers at more
places than before.
The detach routine still calls functions at interrupt level that
aren't reentrant. In theory this could cause a problem, but none
showed up in practice. Future versions should correct this problem,
likely by making the detach process a thread/process at the pccard
level. NEWCARD will do this, and the current pccard layer should
likely be modified to that as well, should it live long enough.
A few style nits of the same form that were in my original patch sent
off to bde were also fixed as part of this process. Mostly use of
!ptr and return ENOPARENS.
This should prevent a crash on suspend with an active ppp link as
well, but that wasn't tested.
Reviewed by: bde
Approved by: jkh
requires current and desired network parameters, so I have created a network parameter structure and used two on them in the softc. This gives a bit of room of expansion. Re-wrote the update check in _net to work with this.
Tidyed up softc due to above.
Removed startccs and startcmd as they were only used by NetBSDs startup timeout.
keyboard port and interrupt is enabled and the driver is attached even
when the keyboard itself is not present when the system is booting.
(This has been the behavior through out 2.X and 3.X, but is somehow
broken in 4.0.)
# I certainly don't recommend people to `hot-plug' the AT keyboard,
# because the interface isn't designed for hot-plugging and such act
# will often break the keyboard controller. But, so many people want to
# do that anyway...
Approved by: jkh
not actually used yet. This created a lot of prototypes.
I moved code around so that the functions are in the same order as NetBSD - this helps diff a lot.
Things that are missing are the TX routine and ifmedia stuff and ioctls
Not all of the stuff is enabled - we are missing calls in ccs_done and ioctl.
Promiscious mode is working.
Am almost ready to use the NetBSD start up routine - essentially all I need
to do is not use a seperate timer to call download_timo.
Other misc. things:
callout_stop is a newish feature for cancelling a timer without
argument checking it.
tried to add a sysctl knob but it doesn't work in the module
enabled infrastructure code to call netbsd bits.
Change disk names to `idad' to avoid naming conflicts with the controller,
and enable the new disk code to pick up the drives.
Tested by: david.w.james@bt.com (existing compaq support)
Reviewed by: msmith
Approved by: jordan
channel DMA. The problem was that the SDC bit (0x04) can only be set in
the MCE state.
PR: kern/16587
Submitted by: Matthew Reimer <mreimer@vpop.net>
Approved by: jkh (in person)
card configuration hassles.
Added a TODO list so I don't forget to finish stuff.
Tidyed up a lot of XXX.
Tidy'd and documented debugging - all DPRINTF have a debug level associated.
RAY_DEBUG = 1, will log packet errors.
#if protect common memory hacking
Don't rely on pccardd for common memory settings.
Added a simple transmit mode - reasonable performance but not great. Will do a version of the NetBSD chained buffers soon. Yup we have two way transmisson!
Fix a stupid bug in the common memory code - the ioctl call was
hidden behind a debug test!
from panicing when disconnecting a USB Wacom Graphire tablet.
jhk approved the fix some time ago, but I forgot to actually commit the
thing.
Reported by: Dirk van Gulik <dirkx@webweaving.org>
Approved by: jhk
is responsible for this and this will lead to malloc 'freeing already
free' type panics. One was in the probe code, the other was in the
pccard eject? code.
Not explicitly approved by: jkh (but the first is fallout from subr_bus.c
rev 1.54 which was an approved commit, the second is the same problem)
adw_pci.c:
Update comments describing supported chips/cards.
adwcam.c:
adwlib.c:
adwlib.h:
Handle more error return codes from the firmware.
Break out the bus reset code into its own function.
Usa a constant for the bus reset hold delay.
Fix an interrupt race problem in adw_idle_cmd_send by
incorporating the poll loop for command completion.
Approved by: jkh@FreeBSDorg
to us, subr_bus.c will free it. This bug (panic: freeing already free)
was exposed by kern/subr_bus.c rev 1.54
Not explicitly approved by: jkh (but this is a showstopper and fallout of
the above approved change)
transferred, do it in complete_rqe instead.
launch_requests: Replace the inadvertently removed splbio() around the
main loop. It may not be necessary, but the biggest
test of this stuff are IDE disks, which I'm not
using.
Remove throttling code, I'm pretty sure it's not
needed any more.
Don't set B_ORDERED, it's not necessary either.
Objected-to-by: alfred
build_rq_buffer: Don't lose the B_ORDERED bit, it still has some
residual meaning. To do this right, Vinum needs to
look at the B_ORDERED bit and order the transfer
across all disks involved. That's an exercise for
another day.
Objected-to-by: alfred
Implicitly-sanctioned-by: jkh
The driver constructs a fake disklabel that makes the 'a' partition
cover the entire DVD-RAM disk. This cannot be changed from the user
side. This solution was chosen because most DVD-RAM will have a
UDF (or until we have that CD9660) filesystem on it covering the
entire disk, its not really thought as a real random access device.
This might change over time, but for now this is what we have, and
it is compatible with CDROM's etc, that makes using the minidisk
subsystem less than ideal, because of !modulo BDEV_SIZE blocks.
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
Set DRIVE_MAXACTIVE and VINUM_MAXACTIVE to 30000, effectively
disabling the request limitation code. This code was added as an
attempt to escape from a bug which seems to have gone away, and it's
very likely I'll remove the code Real Soon Now, but I don't want to do
it just yet.
struct drive: Remove references to vnode pointers, including debug
output. Vinum now talks directly to the device driver. Instead, add
a dev_t.
enum plexorg: Add an instance for RAID-4.
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
Approved-by: jkh
set_sd_state: update the state of a subdisk in a multi-plex volume
more correctly.
update_plex_state: Bring the plex up correctly when the last subdisk
comes up.
checksdstate: Update comments.
vpstate: Don't return an "up" state on a degraded, unattached plex.
start_object: Return a sensible error message when trying to revive a
subdisk whose drive is down. Previously it returned EBUSY.
Approved-by: jkh
data corruption. It's a wonder it worked at all.
Led-on-the-right-path-by: dillon
revive_block: Add treatment for RAID-4.
Add function parityrebuild, called by revive_block and parityops.
Approved-by: jkh
the tsleep call flags.
Submitted-by: Bernd Walter <ticso@cicely.de>
Remove references to vnode pointers, including debug output. Vinum
now talks directly to the device driver.
bre: Add case for RAID-4.
sdio: Don't try to write to a down drive. Set the sd state instead.
Approved-by: jkh
vn_open. This is necessary in order to be able to open drives before
the root file system is mounted. This also involves restructuring the
drive struct, which no longer contains a vnode pointer. Instead,
open_drive sets an open flag. It's a horrible kludge, and I'll gladly
borrow a Danish axe and hack it in little pieces when devfs comes.
read_drive, write_drive, drive_io_done: Replace with driveio. The
function names are now macros.
driveio: Fix horrible, embarrassing breakage which was the reason why
read_drive and write_drive existed in the first place.
Code-torn-to-shreds-by: dillon
format_config: Don't save config of objects in referenced state. They
get rebuilt automatically.
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
Replace the preprocessor variable names BDEV_MAJOR and CDEV_MAJOR with
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
vinum_scandisk: Don't free memory twice on error, once is enough.
Approved-by: jkh
to RAID-5. peter claims that it might be faster for sequential
reading, since the drive caches don't trip over the parity blocks. I
have seen no evidence to support this, but it's a trivial change.
Requested-by: peter
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
atoi(): Remove, nobody was talking to it.
give_sd_to_drive: If no space is available, make the subdisk down,
don't delete it.
Change the manner in which the subdisk count was maintained to avoid
cases where the count was not adjusted correctly.
config_drive: Check if we have subdisks referencing us, and add them
if so. This fixes problems which arose when a drive is replaced in a
running system.
config_sd: Add support for a keyword 'partition', whose meaning will
be revealed in the fullness of time.
Cosmetic: Shorten some console messages.
Approved-by: jkh
to SI_SUB_VINUM, thus making it possible for Vinum to access I/O
devices and start.
Replace the preprocessor variable names BDEV_MAJOR and CDEV_MAJOR with
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
Style fixes: replace NULL with 0 where appropriate.
Submitted-by: Charlie Root <root@sms-1.follo.net> (yup, that's all I
have to go on).
Approved-by: jkh
seriously- only attempt to logout a previously logged in fabric device.
Fix a longstanding bug for aborting overtime commands- handle halves
have always been reversed.
Clean up some error messages to indicate channel number.
Approved:jkh
Added receive code and support for Webgear encapsulation.
More debugging macros/functions.
conditionalised timeout for start/join network
conditonalised attribute/common memory hacks
identified tracking code with XXX_TRACK
sorted out initialistion of instance structure to some extent
finished docuementing the start/join sequence
The code doesn't compile (I'll do that in a minute), but functionally
it gets to receveing the interrupt from the start or join net command.
There is a lot of code to deal with the limitations of the PCCard memory
mapping code - I'm changing some of it hence the check in to preserve something
that worked.
Call intr_teardown on detach.
Always add non masterdevice from unit 2 upwards.
Update to the pccard code, at least some cards are now working,
more testing to follow.
from useful drivers such as the 3D DRI drivers I will be porting for
hardware accelerated OpenGL. The hardware will still be reported during
boot using the nomatch system.
Approved by: jkh
was needed to make attach/detach of devices work, which is
needed for the PCCARD support.
(PCCARD support is still not working though, more to come on that)
Support the CMD646 chip which is used on many alphas, sadly only
in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes.
Lots of cosmetic fixes here and there.
Sorry for the size of this megapatchfromhell but it was not
possible otherwise...
newbus patches based on work from: dfr (Doug Rabson)
accept a new command; in high load cases it may be too busy for the old
value.
This loop needs something to tie it to real time, rather than just the CPU's
ability to fetch from the L1 data cache, but this hack works for now.
Approved by: jkh
1) Non-AST4 multiport cards were broken by bypassing the code that changes
`idev' to the multiport master device.
2) AST4 multiport cards apparently were broken by inverting the test for
the master device having an irq.
3) Error handling for nonexistent master devices was broken by removing a
check for a null pointer.
4) `int' error codes returned by bus_get_resource() were assigned directly
to the boolean variable com->no_irq. Probably harmless, since the
boolean is implemented as a u_char.
Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com>
part 2) by yokota
Approved by: jkh
Andrew's problems with SCSI on some alphas- do not call isp_update
directly to update parameters- just mark them as being ready to
update for the next command- the system would just hang on a READ
CAPACITY for a drive. Really annoying because it wouldn't even timeout
(and it has a timeout) so either the SET PARAMETERS call was nuking
things or the f/w was really dropping the ball.
approved: jkh
Reviewed by: gallatin@freebsd.org
is gone as a define. We just don't support fast posting for anything less
than the 1240/1080/1280/12160 or Fibre Channel cards.
Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44
bytes are allowed).
Approved: jkh
- Remove all the code intended to deal with experimental
C1010 revisions. This code got useless due to commercial
chip revisions having been fixed.
Fixes:
- Rewrite/rework the WSR condition handling.
Previous drivers snooped on the BUS through the SBDL IO
register and this has been discovered to trigger a spurious
SCSI parity error when WSR had been set by chip and cleared
by SCRIPTS prior to reading SBDL bit [0...7].
On the other hand, the C1010 does not use the SWIDE register
when synchronous data transfers are taking place and
requires a CHMOV (1) WHEN DATA_IN to be performed in order
to move to memory the residual byte when WSR is set and
the residual byte is useful data.
BTW, the new WSR handling by the driver is simpler.
- No longer attempt to read from SCRIPTS the SBDL register.
This is intended to avoid to be victimized again by any other
issue regarding the handling of this register by 8xx chips.
Miscellaneous:
- The driver is now able to handle the WSR + IGN RESIDUE
condition at the end of a DATA IN I/O without need of a
programmed interrupt. It is a minor? optimization.
- A few other minor cosmetic changes.
This driver version fixes notably a permanent SCSI parity
error condition at boot that can be triggerred due to recent
changes in cam_xpt.c between 1.79 and 1.80.
Changes in CAM/XPT are fine, but the new handling of the full
INQUIRY may trigger the driver problem when a target returned
an odd value in the `additionnal length' field of the INQUIRY
response.
The diff against previous driver version is large, but it
consists approximatively in:
- 350 lignes removed and not compiled in previous drivers
(They addressed experimental C1010 revisions)
- 250 lignes added or changed, half being comments or empty
lines.
So, in fact, the real changes are about 120 lines of source.
About 80 lines address SCRIPTS changes and about 40 lines
address C code changes.
Approved by: jkh
New WSR handling reviewed by Pamela Delaney <pam.delaney@lsil.com>
(For back-porting to Linux sym53c8xx driver 1.6x series)
for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3)
support- but not with PPR just yet. Fix and clarify fetching of
return parameter for getting firmware rev which for the 2200 contains
the connection topology (Private Loop (NL-port), N-port, FL-port,
F-port). Synthesize the connection topology for the 2100 which can
only be Private Loop or FL-port. Handle a couple of new async
mailbox commands which signify connection in Point-to-Point mode
(N-port or F-port) or indicate various toe stubbing getting to same.
Approved: jkh@freebsd.org
won't appear on the screen, and "blinking" and "destructive" cursor
won't appear in the vty for which the text cursor is currently hidden.
Approved by: jkh
problem was basically (for offset > 4096):
vtophys(addr) + offset != vtophys(addr + offset)
Also, use TD's with a maximum size of 4k instead of 8kb for OHCI
controllers.
This problem occurs in drivers that use large transfer sizes:
umass, host2host and ethernet with jumbo frames.
for optimizing the unpause operation no-longer exist, and this is much
safer.
When restarting the sequencer, reconstitute the free SCB list on the card.
This deals with a single instruction gap between marking the SCB as free
and actually getting it onto the free list.
Reduce the number of transfer negotiations that occur. In the past, we
renegotiated after every reported check condition status. This ensures
that we catch devices that have unexpectidly reset. In this situation,
the target will always report the check condition before performing a
data-phase. The new behavior is to renegotiate for any check-condition where
the residual matches the orginal data-length of the command (including
0 length transffers). This avoids renegotiations during things like
variable tape block reads, where the check condition is reported only
to indicate the residual of the read.
Revamp the parity error detection logic. We now properly report and
handle injected parity errors in all phases. The old code used to hang
on message-in parity errors.
Correct the reporting of selection timeout errors to the XPT. When
a selection timeout occurs, only the currently selecting command
is flagged with SELTO status instead of aborting all currently active
commands to that target.
Fix flipped arguments in ahc_match_scb and in some of the callers of this
routine. I wish that gcc allowed you to request warnings for enums passed
as ints.
Make ahc_find_msg generically handle all message types.
Work around the target mode data-in wideodd bug in all non-U2 chips.
We can now do sync-wide target mode transfers in target mode across the
hole product line.
Use lastphase exclusively for handling timeouts. The current phase
doesn't take the bus free state into account.
Fix a bug in the timeout handler that could cause corruption of the
disconnected list.
When sending an embedded cdb to a target, ensure that we start on a
quad word boundary in the data-fifo. It seems that unaligned stores
do not work correctly.
is initialised by usb_init.
This might solve problems with some controllers not being initiliased
properly, because a delay was effectively a tsleep that returned
immediately.
Approved by: jhk
the PIRQD bit.
This fixes the problem of uhub0 hanging forever during boot when USB
keyboard support is switched on in the BIOS on motherboards with Intel
chipsets (UHCI).
Approved by: The Sheep
fix support for multiple HPT & Promise controllers.
support mixed 33/66 devices on the Promise 66 controllers.
fix the refcount stuff in the atapi drivers.
misc cleanups.
support is also included for the ASC38C1600 Ultra160 chipset, but
as firmware is not yet available for this chip, it is disabled.
Approved by: jkh@FreeBSD.org
Also update wicontrol to enable/disable encryption, set WEP keys and set the
TX key index. Silver cards only have 40-bit keys. This is something of a quick
hack, but it works well enough for me to commit this from the LinuxWorld
exhibit floor.
The WEP support only shows up if you have a card that supports it.
Would have been approved by: jkh, if he hadn't wandered off somewhere
Approved in his place by: msmith, who's standing right here
bus_delete_resource.
Fixes a problem when the probe succeeded, but the attach failed. The
release of the resources was done inproperly.
Approved by: jkh
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
Some controllers submit bogus pointers to the Done queue.
ohci_hash_find_td fails to find these in its hash and panics. Instead of
panicing we now assume the whole done queue is lost and let the timeout
code to clean up the mess after us.
condition.
- 1 line change that allows to balance chips between ncr
and sym using pci compat option (not compiled by default
in 4.0 but maintains the driver source 3.4 compatible).
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
Try to support older systems reporting irq0 for the first channels.
Support sharing of the std interrupts (says peter :) )
Dont use READ_CD on normal data reads (2048 bytes), too many old drives
doesn't support this command even if the std says "shall" :(, but still
use READ_CD on all other blocksizes.
Add the geometry to the ad probe, its still usefull.
does ignore DCD. Even TIOCMGET cannot read DCD as the firmware doesn't
report it. This has pretty interesting effects for ppp(8) which runs
in clocal mode and polls carrier (!). (Specialix's linux driver does
this too)
Also update the firmware to 3.0.6 for the SX cards, as apparently there
was a problem with floating (disconnected) DCD pins causing stray carrier
transitions, especially at port open time.
It seems to work here, and carrier loss is detected nearly immediately
rather than having to wait for a LQR timeout (a few minutes) before ppp(8)
gives up.
DCD problem noted by: nsayer
Dont be so verbose in the probe, only ONE line printed now, to get more
info boot verbose. Centralise most printf's in ata-all & ata-dma to use
the ata_printf function, it saves alot of codelines.
Repeat the identify command if drive fails the first.
Protect the timeout functions with splbio.
Dont update the transfer details before we are sure the transfer
succeded, this way they are proberly retried on errors.
Move the handling of next_writeable to userland.
Use the READ_CD command to read CD's. That enables us to read _anything_
via the normal read/write interface. This kindof obsoletes the READAUDIO
ioctl, but we keep that for now.
Update i2c code to build on FreeBSD 3.x and 4.x machines.
Added GPIO audio values for the Askey/Dynalink TV card talken from postings on the V4L mailing list.
Update Australian Channel Set. Submitted by John Birrell <jb@cimlogic.com.au>
Add new Channel Set for France. Submitted by Daniel Dagneaux <dagneaux@lure.u-psud.fr>
doesn't conflict with the parallel port on my miata (0x3bc..0x3bf).
The right solution will be to reserve two port ranges in vga, 0x3b0..0x3ba
and 0x3c0..0x3ca.
Reviewed by: yokota
o Cut out the probed stuff. We no longer need it since newbus implicitly
checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload. Untested because aha doesn't yet
support identify and there are some interactions with PnP that I've
not yet worked out.
With this I can boot the AHA-1542CP FW F.0. All the aha resources
appear to be picked up via pnp now.
The files were repo copied from their original location and are part
way towards being portable.
This should unbreak the EISA support in the driver.
I have not updated files* yet as I'm not quite finished.
the resource table to locate children. The 'at ppbus?' can go again.
Remove a few #if Nxxx > 0' type things, config arranges this for us.
Move the newbus method glue next to the DRIVER_MODULE() stuff so we
don't need extra prototypes.
Don't set device descriptions until after the possibility of the probe
returning an error.
Remove all cdevsw_add() calls, all the drivers that did this also use
make_dev() correctly, so it's not required.
A couple of other minor nits.
isa_device->id_ri_flags and RI_FAST were not implemented and did nothing.
The two drivers that were mistakenly thinking this was working were
cy.c and loran.c - these should be converted to newbus.
GC (garbage collect) isa_device->id_alive
GC userconfig.c references to isa_device->id_scsiid (!).
Fix a long-standing bug where I used a 'break;' instead of a 'continue;';
you had to have multiple ISA boards in non-PnP mode with an 'unknown' board
with a lower MAC address to find this one. Since I have 4 3c5x9 boards
in my test box I was somewhat confused when this happened. :)
Make the messages printed by ep_isa_identify() a little more consistent;
we'll only see them in verbose boot mode but it makes me feel better if
they look nice.
Also, while I'm here, add a mechanism to catch unknown board IDs that
are likely to be 3c509s and allow them to be attached.
PR: kern/16304
Submitted by: Kelly Yancey <kbyanc@posi.net>
Many ed-based Ethernet PC-cards can't get correct MAC address without
this patch.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
Reviewed by: Warner Losh <imp@village.org>
methods for USB devices.
However: with none of the devices I have here suspend seems to work
properly. This is probably a bug in uhci_power which I still have to
look at.
Prodded and pushed by: Christopher Masto <chris@netmonger.net>
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
This is just to make sure we initialize the chip correctly: we need to
make the sure the port select bit in CSR6 is set properly so that we
use the internal PHY for 10/100 support. (The eval boards I have also
include an external HomePNA PHY, but I need to play with that more
before I can support it.)
- The busy wait hack in usbdi.c was doing its timeout in microseconds
instead of milliseconds.
- if_aue.c:aue_intr() is creating a bitmask by and'ing two bits when it
should be or'ing them.
Submitted by: Lennart Augustsson
correctly on both master and slave.
Smash together the ata_params & atapi_params structures as they
are more or less equal anyways.
Get rid of the last SYSINIT's in here.
the same vendor and logical ID. The rest I am not sure whether they
are vendor or logical, but it won't hurt if I've put a vendor ID here
as merely will not match. These came from the old sio-pnp code, hence
the uncertainty about which ID it is.
running. It turns out that trying to read the MAC address when there's
no firmware creates a zero length transfer. This apparently doesn't
hurt anything on a UHCI controller, but OHCI controllers generate an
IOERROR, and the device doesn't initialize.
Instead, check the bcdDevice revision code. We know this will be
different when the firmware is running, so if we detect the firmware's
code instead of the bare hardware's code, we skip the firmware load.
Prober support for the VIA 82C686, I finally got the right datasheet.
Get rid of atapi_wait, merge it into ata_wait.
Avoid a couple of races by using asleep instead of tsleep.
Always use 16bit transfers on ISA systems.
Clear up the atapi_read/write functions.
of the Broadcom BCM5201 PHY on the LinkSys USB100TX adapter so that the
link LED correctly (lights up amber for 10mbps link, green for 100mbps
link).
Note that the sticker on the bottom of the adapter says amber for 10
and green for 100, but the appendix in the manual that comes with
the adapter says green for 10 and amber for 100. Given that there doesn't
seem to be any way to make the hardware produce the latter combination,
I think it's safe to say the sticker is right and the manual is wrong.
I'm just shocked, shocked I tell you.
- Split terminal emulation code from the main part of the driver so
that we can have alternative terminal emulator modules if we like in
the future. (We are not quite there yet, though.)
- Put sysmouse related code in a separate file, thus, simplifying the
main part of the driver.
As some files are added to the source tree, you need to run config(8)
before you compile a new kernel next time.
You shouldn't see any functional change by this commit; this is only
internal code reorganization.
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
been so positive that I'm going to go ahead and commit this now rather
than do another round of patches.
My Adaptec 1460D works great with these changes.
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.
Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.
Submitted by: mdodd
things like sound cards can get called "Parallel port". A note to the
unwary; the isa-pnp devices in the system are probed like PCI - each
device ID is passed to *all* isa probe routines to find the best match.
If the driver is not prepared to deal with this, it must abort in this
scenario or it will try and claim all PnP devices.
Update list of supported products.
Adjust probe message to include the ASC3030.
advansys.c:
Fix a long standing bug in the error recovery strategy. In order
to keep recovery simple, we freeze the SIMQ, stopping the XPT from
submitting new requests. Unfortunately, we also will freeze the
SIMQ if bus_dmamap_load blocks or we run out of controller resources.
On cards with limited resources it was possible to freeze the
SIM a second time and never unfreeze it. Now we more carefully
track our exception state so we never freeze the SIMQ more than
once.
Don't rely on pointers fitting in a 32bit field stored in the
per-transaction data structures on the card. Use an index to
an array of transaction mapping structures instead. This should
allow this driver to work on the Alpha.
Deal with the ASC3030 which is almost idistinguishable from the
ASC3050. Unfortunately the ASC3030 does not work at Ultra speeds,
so if we can't find an eeprom, we must assume that ultra is disabled.
The SIIG cards using the 3030 do not have eeproms. As a side effect,
we now honor the ultra disable bit in the eeprom if it is present.
Don't bother attempting to write corrected eeprom data back to the
eeprom. We can function just fine if the data is corrupted and
I'd rather not risk messing up the user's eeprom.
Modify the interrupt handler to catch latched external bus rests.
Dynamically determine the maximum number of S/G elements we can
map at a single time. The nature of the firmware interface for
these cards makes this value dependent on the number of "queues"
the card can support.
advlib.c:
advlib.h:
advmcode.c:
advmcode.h:
Synchronize with the latest firmware image released in the
Linux Advansys driver.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
Do not not not call m_freem() in the txeof routines. Let the netisr routine
do it. This also makes the tx netisr queuing much simpler (I can just use
another ifqueue instead of the mess I had before.)
Thanks to Bosko Milekic for making me actually think about what I was
doing for a minute.
Note1: the correct interrupt level is invoked correctly for each driver.
For this purpose, drivers request the bus before being able to
call BUS_SETUP_INTR and BUS_TEARDOWN_INTR call is forced by the ppbus
core when drivers release it. Thus, when BUS_SETUP_INTR is called
at ppbus driver level, ppbus checks that the caller owns the
bus and stores the interrupt handler cookie (in order to unregister
it later).
Printing is impossible while plip link is up is still TRUE.
vpo (ZIP driver) and lpt are make in such a way that
using the ZIP and printing concurrently is permitted is also TRUE.
Note2: specific chipset detection is not done by default. PPC_PROBE_CHIPSET
is now needed to force chipset detection. If set, the flags 0x40
still avoid detection at boot.
Port of the pcf(4) driver to the newbus system (was previously directly
connected to the rootbus and attached by a bogus pcf_isa_probe function).
- Add vendor/device ID for Corega USB-T ethernet adapter to necessary
places so that it will work with the kue driver.
- Add vendor/device ID for CATC Netmate devices for driver to be added
soon.
- Get really crazy about netisr stuff: avoid doing any mbuf allocations
or deallocations at splbio/splusb.
- Fix if_aue driver so that it works with LinkSys USB100TX: you need
to flip the GPIO bits just the right way to put the PHY in the right
mode.
layout. It seems that I cleaned it up a bit too much and confused a few
if () {
if () {
} else {
}
}
statements in the obvious manner.
This allows the driver to transmit packets again. *sigh*
packets into a single buffer, and set the DC_TX_COALESCE flag for the
Davicom DM9102 chip. I thought I had escaped this problem, but... This
chip appears to silently corrupt or discard transmitted frames when
using scatter/gather DMA (i.e. DMAing each packet fragment in place
with a separate descriptor). The only way to insure reliable transmission
is to coalesce transmitted packets into a single cluster buffer. (There
may also be an alignment constraint here, but mbuf cluster buffers are
naturally aligned on 2K boundaries, which seems to be good enough.)
The DM9102 driver for Linux written by Davicom also uses this workaround.
Unfortunately, the Davicom datasheet has no errata section describing
this or any other apparently known defect.
Problem noted by: allan_chou@davicom.com.tw
drive the transmitter, we have to check the interface's send queue in the
TX end of frame handler (i.e. the usb bulk out callback) and push out new
transmissions if the queue has packets in it and the transmitter is
ready. But the txeof handler is also called from a USB callback running
at splusb() too.
Grrr.
Use IFQ_MAXLEN instead. This seemed like a good idea at the time since
most 3c509s have all of 2k for their TX fifo. My intention was to revisit
ifq_maxlen and auto-scale it or something.
ttcp-t: 16777216 bytes in 21.53 real seconds = 761.07 KB/sec +++
ttcp-t: 2771 I/O calls, msec/call = 7.96, calls/sec = 128.72
ttcp-t: 0.0user 2.9sys 0:21real 13% 20i+280d 222maxrss 0+2pf 717+0csw
ttcp-r: 16777216 bytes in 14.11 real seconds = 1161.48 KB/sec +++
ttcp-r: 2050 I/O calls, msec/call = 7.05, calls/sec = 145.33
ttcp-r: 0.0user 1.4sys 0:14real 10% 87i+1198d 196maxrss 0+1pf 1949+186csw
I've got some tweaks that move the TX speed up to the RX speed but I've
got to groom them from the mess I've made of my source tree.
Yelled at by: wpaul
ddb is entered. Don't refer to `in_Debugger' to see if we
are in the debugger. (The variable used to be static in Debugger()
and wasn't updated if ddb is entered via traps and panic anyway.)
- Don't refer to `in_Debugger'.
- Add `db_active' to i386/i386/db_interface.d (as in
alpha/alpha/db_interface.c).
- Remove cnpollc() stub from ddb/db_input.c.
- Add the dbctl function to syscons, pcvt, and sio. (The function for
pcvt and sio is noop at the moment.)
Jointly developed by: bde and me
(The final version was tweaked by me and not reviewed by bde. Thus,
if there is any error in this commit, that is entirely of mine, not
his.)
Some changes were obtained from: NetBSD
Packets are received inside USB bulk transfer callbacks, which run at
splusb() (actually splbio()). The packet input queues are meant to be
manipulated at splimp(). However the locking apparently breaks down under
certain circumstances and the input queues can get trampled.
There's a similar problem with if_ppp, which is driven by hardware/tty
interrupts from the serial driver, but which must also manipulate the
packet input queues at splimp(). The fix there is to use a netisr, and
that's the fix I used here. (I can hear you groaning back there. Hush up.)
The usb_ethersubr module maintains a single queue of its own. When a
packet is received in the USB callback routine, it's placed on this
queue with usb_ether_input(). This routine also schedules a soft net
interrupt with schednetisr(). The ISR routine then runs later, at
splnet, outside of the USB callback/interrupt context, and passes the
packet to ether_input(), hopefully in a safe manner.
The reason this is implemented as a separate module is that there are
a limited number of NETISRs that we can use, and snarfing one up for
each driver that needs it is wasteful (there will be three once I get
the CATC driver done). It also reduces code duplication to a certain
small extent. Unfortunately, it also needs to be linked in with the
usb.ko module in order for the USB ethernet drivers to share it.
Also removed some uneeded includes from if_aue.c and if_kue.c
Fix suggested by: peter
Not rejected as a hairbrained idea by: n_hibma
Driver is not functional yet, but does compile. Tests with xe cards
indicates that it doesn't panic the machine when they are present, but
fail to probe. Interface help in the pcic/pccard layers are needed to
complete this driver.
o ifdef out pccardchip.h (almost all of it, there are dangling bits
o Add rid/res members to pccard_function
o remove pct/pch from pccard_softc
o map memory properly in scan_cis (almost, see XXX for more work)
o manage ccr.
o remove bogus comment I added about touching the ccr being a layering
violation for pccard. It is properly done at that level.
o More function prototyping
whilst we are playing or recording. since we should irq ~20 times/sec when
active, this should never trigger. in theory. if it never does trigger,
the check will be removed.
- Set MAX_OFFS driver compile option to 63 (was 64 which is wrong).
- Fix a typo in the SYMBIOS NVRAM layout structure and add field and
bit definition for the support of PIM_NOBUSRESET.
- Report to XPT PIM_NOBUSRESET and PIM_SCANHILO if set by user in NVRAM.
- Negotiate SYNC immediately after WIDE response from the target as
suggested by Justin Gibbs.
- Remove some misleading comment about CmdQue handling by CAM.
- Apply correctly the MAX_WIDE and MAX_OFFS driver options.
It seems that the IDE system uses 0x3f6 for itself, which conflicts with
fdc's default 0x3f0-3f7 allocation range. Sigh. Work around this.
Use bus_set_resource() rather than allocating specific areas, it makes
the code a little cleaner.
Based on work by: dfr
Note: the .INF file for LinkSys's driver says the vendor ID is 0x66b,
however this does not agree with the vendor ID listed for LinkSys in
the company list from www.usb.org. In fact, 0x66b doesn't seem to appear
in the company list at all. Furthermore, this same vendor ID crops
up in some of the D-Link .INF files. Frankly I don't know what the heck
is going on here, but I need to add 0x66b to usbdevs and call it
something, so here we are.
certain PHY addresses in aue_miibus_readreg(). Not all adapters based
on the Pegasus chip may have their PHYs wired for the same MII bus
addresses: the logic that I used for my ADMtek eval board might not
apply to other adapters, so make sure to only use it if this is really
an ADMtek eval board (check the vendor/device ID).
This will hopefully make the LinkSys USB100TX adapter work correctly.
makes it a little easier to notice that parity checking an 8bit sram
isn't working.
Turn on scb and internal data-path parity checking for all pci chips types.
We were only doing this for ultra2 chips.
After clearing the parity interrupt status, clear the BRKADRINT. This
avoids seeing a bogus BRKADRINT interrupt after external SCB probing
once normal interrupts are enabled.
an URB before sending ZLP) set to the default. Choosing a bad value
can apparently cause a lockup on some machines/controllers.
Reported by: Doug Ambrisko
93cx6.c:
Make the SRAM dump output a little prettier.
aic7xxx.c:
Store all SG entries into our SG array in kernel space.
This makes data-overrun and other error reporting more
useful as we can dump all SG entries. In the past,
we only stored the SG entries that the sequencer might
need to access, which meant we skipped the first element
that is embedded into the SCB.
Add a table of chip strings and replace ugly switch
statements with table lookups.
Add a table with bus phase strings and message reponses
to parity errors in those phases. Use the table to
pretty print bus phase messages as well as collapse
another switch statement.
Fix a bug in target mode that could cause us to unpause
the sequencer early in bus reset processing.
Add the 80MHz/DT mode into our syncrate table. This
rate is not yet used or enabled.
Correct some comments, clean up some code...
aic7xxx.h:
Add U160 controller feature information.
Add some more bit fields for various SEEPROM formats.
aic7xxx.reg:
Add U160 register and register bit definitions.
aic7xxx.seq:
Make phasemis state tracking more straight forward. This
avoids the consumption of SINDEX which is a very useful register.
For the U160 chips, you must use the 'mov' instruction to
update DFCNTRL. Using 'or' to set the PRELOADED bit is
completely ineffective.
At the end of the command phase, wair for our ACK signal
to de-assert before disabling the SCSI dma engine. For
slow devices, this avoids clearing the ACK before the
other end has had a chance to see it and lower REQ.
controllers will run at U2 speeds until I can complete the U160 support
for this driver.
Correct a termination buglet for the 2940UW-Pro.
Be more paranoid in how we probe and enable external ram, fast external
ram timing and external ram parity checking. We should now work on
20ns and 8bit SRAM parts.
Perform initial setup for the DT feature on cards that support it.
Factorize and clean up code. Use tables where it makes sense, etc.
Add some delays in dealing with the board control logic. I've never
seen this code fail, but with the ever increasing speed of processors,
its better to insert deterministic delays just to be safe. This stuff
is only touched during probe and attach, so the extra delay is of no
concern.
ethernet adapters that are supported by the aue and kue drivers.
There are actually a couple more out there from Accton, Asante and
EXP Computer, however I was not able to find any Windows device
drivers for these on their servers, and hence could not harvest
their vendor/device ID info. If somebody has one of these things
and can look in the .inf file that comes with the Windows driver,
I'd appreciate knowing what it says for 'VID' and 'PID.'
Additional adapters include: the D-Link DSB-650 and DSB-650TX, the
SMC 2102USB, 2104USB and 2202USB, the ATen UC10T, and the Netgear EA101.
These are all mentioned in the man pages, relnotes and LINT.
Also correct the date in the kue(4) man page. I wrote this thing
on Jan, 4 2000, not 1999.
layer is trying to access the now unexistant chip functions.
o Added DEVPRINTF which is like DPRINTF only calls device_printf.
o Made it possible to define PCICDEBUG
o Remove ph_parent and use the softc pointer sc instead in pcic_handle.
o Remove all references to dv_xname
o Add some debug messages.
o enable MI attach/detach calling for pccard.
o convert pcic_chip_socket_{en,dis}able to pcic_{dis,en}able_socket
and connect them to the power_{enable,disbale}_socket.
o Remove pccard pointer from pcic_softc.
o GC some unused pccard functions.
o Convert pccard_chip_socket* to POWER_ENABLE_SOCKET
o kill pccard_attach_args.
o power_if.m updates. More to come.
o Rename FDC_PCMCIA to FDC_NODMA to allow systems that don't have dma
for floppies.
o Remove all but two FDC_YE ifdefs. They aren't needed.
o Move defines for YE_DATAPORT to fdreg.h.
Not fixed:
o The pccard probe/attach. However, motivated individuals can more
easily add this now.
This is a merge of changes I've had in my tree for a long time. These
fixes were tested on my VAIO with its normal floppy. Please let me
know if I broke anything.
Prodded by: Peter Wemm <peter@freebsd.org>
This is the hack that compensates for when bios vendors "forget" to
include the fdc control (0x3f7) port in their io port mappings. Instead
of accessing ports outside of a range allocated to a handle, simply
allocate the port directly. It even shows up in the probe..
machine but leave your KLSI adapter plugged into your USB port, it
may stay powered on and retain its firmware in memory. Trying to load
the firmware again in this case will wedge the chip. Try to detect this
in the kue_load_fw() routine and bail if the firmware is already
loaded and running.
Also, in the probe/match routine, force the revision code to the
hardware default and force a rescan of the quirk database. This is
necessary because the adapter will return a different revision code
if the firmware has been loaded. Without the firmware, the revision
code is 0x002. With the firmware, the revision code is 0x202. This
confuses the quirk mechanism, which won't match a quirk to a device
unless the revision code agrees with the quirk table entry.
This makes probe/attach of these devices somewhat more reliable.
Also add a few comments about the device's operation.
In particular:
- Don't leave resources allocated in the probe routine. Allocate them
during probe and release them. Probe's job is to identify devices only.
- Don't abuse the ivars pointer.. (!). Create real ivars and use the
proper access system. (the bus_read_ivar method)
- Don't add the children until attach() has successfully grabbed the
hardware, otherwise there are potential leaks if attach fails.
on alpha.
Submitted-by: Bernd Walter <ticso@cicely.de>
struct sd: Add a field for the pid of the reviver when the subdisk is
reviving.
Replace block device macros with generalized device macros.
alpha.
Explicitly type large scalar parameters to avoid compilation warnings
on alpha.
Submitted-by: Bernd Walter <ticso@cicely.de>
Make better checks that the revive block size is valid, silently set
it to the defaults if not.
Replace block device macros with generalized device macros.
alpha.
Modify the manner in which we lock RAID-5 plexes. This appears to
solve some of the elusive panics we have seen with corrupted buffer
headers (specifically the zeroed-out b_iodone field).
Submitted-by: Bernd Walter <ticso@cicely.de>
solve some of the elusive panics we have seen with corrupted buffer
headers (specifically the zeroed-out b_iodone field).
Submitted-by: Bernd Walter <ticso@cicely.de>
'iswhite'. The original change was required because of name
conflicts.
Add key pairs for the keywords 'mv' and 'move' (part of the move
command).
Add comments.
drives. This function just does the low-level configuration changes;
the resultant subdisk is stale if it previously had any contents,
otherwise it is empty (i.e. in need of initializing if it's RAID-5).
We still need to handle getting the contents moved over, but the
current version will suffice to migrate subdisks from a disk which has
failed.
Submitted-by: Marius Bendiksen <marius@marius.scancall.no>
on alpha.
Submitted-by: Bernd Walter <ticso@cicely.de>
Remove #include of vm/vm_zone.h.
Submitted-by: Someone, I'm sure, but I seem to have lost the
attribution. Sorry.
Get the check for disk devices correct, and return an appropriate
message if the check fails.
shutdown.
Submitted-by: Alfred Perlstein <bright@wintelcom.net>
Correct printf format for pointers to avoid compilation warnings on
alpha.
Submitted-by: Bernd Walter <ticso@cicely.de>
Identify daemon as 'vinum', not 'vinumd', in messages. This
corresponds to the name in ps.
on alpha.
Submitted-by: Bernd Walter <ticso@cicely.de>
Get parameters right for some error messages returned via
throw_rude_remark().
Fix typo in comment.
Remove the 'static' attribute from give_sd_to_drive. This is needed
for the implementation of moveobject() in vinumioctl.c.
Kawasaki LSI KL5KUSB101B chip, including the LinkSys USB10T, the
Entrega NET-USB-E45, the Peracom USB Ethernet Adapter, the 3Com
3c19250 and the ADS Technologies USB-10BT. This device is 10mbs
half-duplex only, so there's miibus or ifmedia support. This device
also requires firmware to be loaded into it, however KLSI allows
redistribution of the firmware images (I specifically asked about
this; they said it was ok).
Special thanks to Annelise Anderson for getting me in touch with
KLSI (eventually) and thanks to KLSI for providing the necessary
programming info.
Highlights:
- Add driver files to /sys/dev/usb
- update usbdevs and regenerate attendate files
- update usb_quirks.c
- Update HARDWARE.TXT and RELNOTES.TXT for i386 and alpha
- Update LINT, GENERIC and others for i386, alpha and pc98
- Add man page
- Add module
- Update sysinstall and userconfig.c
has it blacklisted. Silly us for not planning ahead. Tsk. Anyway-
a 10 year window patch is probably sufficient to still detect
nonsense in the clock but allow us to roll past the year 2000.
code gratefully borrowed from Patrick Stirling who did a lot of the
grunt work on this years ago. There are also some beginnings of
swizzle macros in case we go to a big endian machine. This is just
a first pass at this and is likely to change a bit over the next
Add in a very large amount of target mode support code- this is just
a first pass at this. It's a difficult thing because some of the code
can be in platform independent areas (see isp_target.?) but a lot has
to be in platform dependent areas because of not only the tight coupling
of received commands/events and the specific OS subsystem but because
the platform independent code has (deliberately) no event/wait mechanisms.
of where we could have seen the loop up at least once so it
makes sense. Change some stuff in ispscsicmd so we don't get
stuck there if the loop has never come up yet. Add in some
target mode support code.
down, the dc driver and receiver can fall out of sync with one another,
resulting in a condition where the chip continues to receive packets
but the driver never notices. Normally, the receive handler checks each
descriptor starting from the current producer index to see if the chip
has relinquished ownership, indicating that a packet has been received.
The driver hands the packet off to ether_input() and then prepares the
descriptor to receive another frame before moving on to the next
descriptor in the ring. But sometimes, the chip appears to skip a
descriptor. This leaves the driver testing the status word in a descriptor
that never gets updated. The driver still gets "RX done" interrupts but
never advances further into the RX ring, until the ring fills up and the
chip interrupts again to signal an error condition. Sometimes, the
driver will remain in this desynchronized state, resulting in spotty
performance until the interface is reset.
Fortunately, it's fairly simple to detect this condition: if we call
the rxeof routine but the number of received packets doesn't increase,
we suspect that there could be a problem. In this case, we call a new
routine called dc_rx_resync(), which scans ahead in the RX ring to see
if there's a frame waiting for us somewhere beyond that the driver thinks
is the current producer index. If it finds one, it bumps up the index
and calls the rxeof handler again to snarf up the packet and bring the
driver back in sync with the chip. (It may actually do this several times
in the event that there's more than one "hole" in the ring.)
So far the only card supported by if_dc which has exhibited this problem
is a LinkSys LNE100TX v2.0 (82c115 PNIC II), and it only seems to happen
on one particular system, however the fix is general enough and has low
enough overhead that we may as well apply it for all supported chipsets.
I also implemented the same fix for the 3Com xl driver, which is apparently
vulnerable to the same problem.
Problem originally noted and patch tested by: Matt Dillon
now, but we're getting interrupts!
o Add pcic_suspend/pcic_resume so we can detach our children on suspention
and fix the state of the pcic on resume.
o Remove some unused parts of softc.
o Centralize resource activation/deactivation for pcic bridge chip in
the stylistic pcic_activate/pcic_deactivate.
o Add bus_print_child method so we can see the pccard attachment.
o Add pcic_identify in an attempt to make it possible to automatically id
the pcic devices. This works great, but we cannot divine the irq to use
from this method, nor the memory hole. For the moment, KLUDGE irq to be
10 and memory hold to be 0xd0000.
o Loose the pnp probe stuff. This may be a big mistake, but it is easy
enough to add back later. I did this so the identify routines can do their
thing unmolested by pnp information. The whole identify thing may be a bad
idea to be ripped out later.
o change return type of pcic_intr to void, make it static and ripple
this through the code.
o Add explicit call to bus_generic_attach at the end of pcic_attach to
get any children probed/attached.
o add some comments about future directions/questionable things being
done at different layers, etc.
then invoke the children. As the value of HISR can be read
only once, pass the HISR to the children via struct
csa_bridgeinfo, stored in the ivars of them.
- Clear the contents of serial FIFO upon stopping the DMA for
playing. This may eliminate buzz on playing. Experimental.
(pci dev_id 0x21).
- Start the SCRIPTS processor without resetting the SCSI BUS
at initialization.
- Remove the "Host adapter CCB chain" (got useless given the
new queuing scheme).
- Display correctly the state of SCSI signals, when SCSI BUS
looks bad.
- Cosmetic changes in messages printed out at initialization.
- Notifications and messages on RESET conditions slightly
reworked.
- TEKRAM 24C16 NVRAM support fixed (also reported ok).
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
5in HD 2 heads, 77 cylinders, 8 sectors/track, 1024 bytes/sector
5/3.5in DD 2 heads, 80 cylinders, 8 sectors/track, 512 bytes/sector
Meanings of the rogrammer-readeble fd name were explained by Brian
Fundakowski Feldman and Peter Wemm in hackers list and NOKUBI
Hirotaka.
Reviewed by: nyan
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
devices.
o Return ENXIO from sn_isa_probe
o Fix SN_DEBUG printf
o Use IFQ_MAXLEN rather than 8
I'll fix the isa probe when I get access to a real isa attachment
device to test against here in a few days.
Overly agressive snagging behavior noticed by: phk
- In uhci_intr() check to see if sc->sc_bus.bdev is NULL, and if it is,
ack any pending interrupts and disable them, then return. It is possible
for interrupts to be delivered the moment a handler is set up at attach
time in uhci_pci.c, particularly when attempting to kldload the usb.ko
module after the system is already up. However the driver isn't ready
to field interrupts at that time and certain pointers in the softc
struct aren't initialized yet, and we invariably end up falling off
the end of one of them. The effect is that kldloading the usb module
will panic the system in uhci_intr(). This added sanity check stops
this from happening: I can now kldload the usb.ko module without any
problems and load/attach other USB drivers after it.
Of course the uhci driver has no detach method, but that's another
problem.
- In uhci_run(), set the UHCI_CMD_MAXP bit in the command register to
allow 64-byte packets to be used for full speed bandwidth reclamation.
Certain high speed devices (in this case the ADMtek USB ethernet
adapter) require this bit to be set, otherwise babble errors occur
at the end of large (between 1100 and 1500 byte) transfers. This
should not affect other devices, although supposedly it is less efficient
than the 32-byte setting. Unfortunately, this is a per-bus setting,
not a per-device setting, so we can't just enable it for certain
devices on the USB bus.
Add support, kinda, for megaheartz xjack nic cards. This support
works well for one machine per ethernet segment because it hard codes
the MAC address. The pccardd in -current doesn't have support to
parse the ethernet address from the CIS in the funky way that the
megaheartz card does things (it includes it in the info tuple, as
ascii, which is non-standard). I'd rather kludge this for the moment
and work to read the CIS from the kernel rather than mess with
pccardd.
The isa attachment is untested. The pccard attachment is known to
work since I'm committing over it.
Card Obtained from: Chris D. Faulhaber <jedger@fxp.org>
- Don't keep private copies of some of the data fields from the
ENQUIRY and ENQUIRY2 commands. Instead, standardise on the ENQUIRY2
command for initial adapter information, and keep a copy of the entire
structure. Refer to it where appropriate.
- Move all of the controller description functionality into a new
function. Print lots more controller data if bootverbose is set.
Add knowledge of the DAC960 PR, PT, PTL0 and PRL controllers, rename
the 960PTL -> PTL0 and 1100P -> 1100PVX.
- Correctly terminate an error message.
The controller interface procedures have been reviewed against the
Mylex-supplied documentation; no changes appear necessary at this
time.
on all combinations (I hope)...
Add DMA support for the AMD 756 chip (K7 chipset) this is actually the
same as the VIA 82C686 chip (the ATA part that is).
Treat the intel MX chipset PIIX as a PIIX4
Allow UDMA on all disks that say they can handle it.
Cleanup probe printf's a bit
Remove alot of the old #ifdef DEBUG crap.
going to a lot of trouble to identify it and set the tag and then not use
it. Convert the pnp id matching to the preferred table based system.
@@@0001 (CMI8330 ldn 0) is a mss, not a SB.
of these are bound to have a PNP05xx compatid, but there's no easy way to
tell. Since it's just an ID list and uses the pnp header's description
strings rather than encoding strings here, it doesn't seem to be too
expensive to err on the safe side.
misdetecting FIFO capabilities, at least on my girlfriend's Thinkpad 755,
the driver doesn't work using the FIFO.
While i was at it, i (partially) fixed option FCC_YE since it would no
longer have compiled at all under -current. I've also made an attempt
to document the device driver flags value (ab-)used internally by this
option.
RELENG_3 candidate, but with a slightly different patch there (will go
to jkh in email).
or less. This is a kludge because there is no support for delayed
creation of threads early in the boot process.
NEWCARD new boots and the thread process starts and is visible from
ps.
Now, on to dev/pccard.
the input fifo to be returned as successful and frozen. Most, if not
all, peripheral drivers do not check the qfrozen bit for successfully
completed commands, so the result would not only be lost commands, but
devices locked out from receiving commands. This was a bad bug that
crept in two or three months ago during some target mode work.
config_intrhook_establish doesn't work. Children aren't yet attached
properly, but that's ok because pccard would likely panic in its
current shape.
o Save dev of pcic early in attach process
o save dev in pcic_handle for use in pcic_create_event_thread.
o Remove direct attachments of pccard children for now
o move establishment of pcic kthread to config_intrhook.
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
o minor formatting nits
o remove the bus_map/unmap calls. FreeBSD doesn't need them.
o Fix most of the compiler warnings remaining (some still remain, but they
are releated to calling functions that are going to change, so I did
not bother).
broken bit work-around enabled.
* Fixed a bug that made MDP not work. (However, MDP is actually not tested
due to lack of hardware using this feature).
* Chip table changed to support the C1010 B0 w/o the U3EN bit work-around
enabled.
* Add the SYM_SETUP_MAX_LUN, SYM_SETUP_LP_PROBE_MAP (used to tell the
driver about chips that are to be claimed with lower priority than old
PCI bus based driver (typically the ncr)), SYM_SETUP_SCSI_DIFF, and
SYM_SETUP_PCI_PARITY options.
Submitted by: Gerard Roudier <groudier@club-internet.fr>
main component in the southbridge chip to determine which VIA chip
we are dealing with.
Try to enable DMA on generic controllers that say they has the
capability, instead of relying on the BIOS to have set it up.
- Add a flag DC_TX_INTR_ALWAYS which causes the transmit code to
request a TX done interrupt for every packet. The PNIC seems to need
this to insure that the sent TX buffers get reaped in a timely fashion.
- Try to unreset the SIA as soon as possible after resetting the whole
chip.
- Change dcphy to support either 10/100 or 10Mbps only NICs. The
built-in 21143 ethernet in Compaq Presario machines is 10Mbps only
and it doesn't work right if we try to advertise 100Mbps modes during
autoneg. When restricted to only 10mbps modes, it works fine.
Note that for now, I detect this condition by checking the PCI
subsystem ID on this NIC (which has a Compaq vendor/device ID).
Yes, I know that's what the SROM is supposed to be for. I'm deliberately
ignoring the SROM wherever possible. Sue me.
The latter two fixes allow if_dc to work correctly with the built-in
ethernet on certain Compaq Presario boxes. There are liable to be quite
a few people using these as their home systems who might want to try
FreeBSD; may as well be nice to them.
Now if anybody out there has an Alpha miata with 10Mbps ethernet and
can show me the output from pciconf -l on their system, I'd be grateful.
Add a missing DELAY(1) in ata_wait.
Change the info from ad_version, so the ATA version from the disk can
be used to quantify the DAM modes valid for this drive, ie be more
selective with turning DMA on on older disks that should not support it..
Fix the probe for BIOS enabled DMA in the generic case, master/slave
was reversed in the test.
Check the return for ata_command in all cases, and print warnings if
it fails.
Call ata_dmainit with all dmamodes off when falling back to PIO mode,
that should take care of both the Promise & HPT366 controllers not
being able to handle the fallback...
Cleanup the printf's in the drivers, use the prober device name (if
possible) instead of ataN-master/slave.
add support for non-pnp cards to sbc
move card identification to sbc
channel-swapping code is in sb now instead of dsp
vibra16x support is still broken, but will be fixed soon
note: sbc is now compulsory for sb cards
for pnp cards use:
device sbc0
for non-pnp cards eg:
device sbc0 at isa? port 0x240 irq 5 drq 3 flags 0x15
(hints as oldpcm)
both in addition to:
device pcm0
Reviewed by: tanimura,dfr
Said he liked it: peter
* lockstatus() and VOP_ISLOCKED() gets a new process argument and a new
return value: LK_EXCLOTHER, when the lock is held exclusively by another
process.
* The ASSERT_VOP_(UN)LOCKED family is extended to use what this gives them
* Extend the vnode_if.src format to allow more exact specification than
locked/unlocked.
This commit should not do any semantic changes unless you are using
DEBUG_VFS_LOCKS.
Discussed with: grog, mch, peter, phk
Reviewed by: peter
and fixing some major bugs.
- Add support for the v5 firmware interface, used by the DAC1164P
(tested) and AcceleRAID 352 (untested but should work). We now cover
all of the Mylex family's protocols except for v2 (used by EISA and
Alpha-compatible cards).
- Fix an accounting bug which resulted in endless 'poll still busy'
messages. In situations of high controller load the count of poll
commands could be incremented without actually successfully launching
a command. This totally removes the accounting for status poll
commnads; it was its own worst enemy.
- Add some simple reentry prevention locks to processing of the waiting
and completed command queues to prevent races which could result in
I/O being done or completed twice (both are fatal). This highlights
a need for simple locking primitives in both the UP and SMP kernels.
- Streamline the handling of command completion to reduce the amount of
redundant work being done. Remove the code which tests for commands
that have gone missing in action; nobody has ever seen one of these
and it wouldn't have worked properly anyhow.
- Handle disconnection of drives from the controller in the detach,
not shutdown method. This avoids problems flushing the cache in
a panic when a drive is mounted.
- Don't call bus_generic_detach when disconnecting drives; it doesn't
actually do anything useful.
- Increment the log message index regardless of whether we actually
retrieved one or not. If we run into a message that we can't fetch,
we don't want to spin endlessly complaining about the fact.
- Don't assume that interrupts will work when we're flushing the
controller. We may think they are enabled, but in eg. a panic
situation the controller may not be able to deliver an interrupt.
attaching to the device via chip*, use the newbus nomatch method to report
the device. This leaves them unattached so that a driver can be easily
loaded to grab them later.
o fix return type of sio_pccard_detach
o don't free softc in deatch, since that is done by newbus
o disconnect interrupt we used to have. Add cookie to com so that we can
tear down the interrupt on unload
o Set gone earlier, but likely doesn't matter
This makes sio pccards work again. Cards that are active when ejects may
not work (but they might, softc goes away quickly).
These changes are unreviewed by bde. I'll make any style changes he wants.
o Expose ed_stop and call it early to shutdown the hardware.
o When releasing the interrupt, pass the cookie for the irq, not
a pointer to the cookie (this is the base problem).
o Release other resources used, just like the ep driver
ralta. These keys combine shift/ctrl/alt function and the AltLock
function. When these keys pressed together with another key, they act
just like the ordinary shift/ctrl/alt keys. When these keys are
pressed and released alone, Alt lock state is toggled.
PR: kern/12475
keymap and pressed, the system panic will be forced.
This feature must be specifically enabled by a new sysctl variable:
machdep.enable_panic_key. Its default value is 0. The panic key
won't do anything unless this variable is set to non-zero.
To use the panic key, add a keyword 'panic' to a key in your
keymap file. The following example assigns the panic function
to SysReq (Alt-PrintScreen) key (keycode 84).
083 del '.' '.' '.' '.' '.' boot boot N
084 panic nop nop nop panic nop nop nop O
085 nop nop nop nop nop nop nop nop O
PR: kern/13721
background ]
Rename sys/pci/pci_ioctl.h to sys/sys/pciio.h to make it easier for
userland programs to use this interface. Reformat the file, and add a
BSD-style copyright to it.
Add a new man page for pci(4). The PCIOCGETCONF, PCIOCREAD, and PCIOCWRITE
ioctls are documented, but the PCIOCATTACHED ioctl is not documented
because it is not implemented.
Change includes of <pci/pci_ioctl.h> to <sys/pciio.h> or remove them
altogether. In many cases, pci_ioctl.h was unused.
Reviewed by: steve
There seems to be some problem with the new rgb_vbi_prog() RISC
code not working for NTSC users.
This means that European teletext users will need to start
Alevt (or open /dev/vbi0) BEFORE starting FXTV (or opening /dev/bktr0)
if they want to capture VBI data for Teletext/Videotext or WaveTop
Reported by: Chris Csanady <cc@137.org>, Kenneth D. Merry <ken@kdm.org>,
Randy Bush <randy@psg.com>
The same goes for CD drivers and tape drivers. In systems with mixed IDE
and SCSI, devices in the same priority class will be sorted in attach
order.
Also, the 'CCD' priority is now the 'ARRAY' priority, and a number of
drivers have been modified to use that priority.
This includes the necessary changes to all drivers, except the ATA drivers.
Soren will modify those separately.
This does not include and does not require any change in the devstat
version number, since no known userland applications use the priority
enumerations.
Reviewed by: msmith, sos, phk, jlemon, mjacob, bde
per discussions on -arch. This is different than -current's pccard
code, but shouldn't have any real difference.
o More code cleanup.
Next step: convert bus_space_* mapping stuff to newbus.
case. The idea is to reduce how often we call mii_tick(), however currently
it may not be called often enough, which prevents autonegotiation from
being driven correctly.
This should improve the chances of successfully autonegotiating media
settings on non-MII 21143 NICs. (Still waiting for confirmation from
some testers, but the code is clearly wrong in any case.)
xxx_query_mode() in the vga and vesa drivers.
- xxx_query_mode() returns 0 (success) and a positive error number.
- Copy mode information on success.
- Remove redundant structure copy.
The bug first found in -STABLE by jmg.
o Implement memory and I/O activation/deactivation. irq not handled.
o switch pcic_chip functions around to use more convenient types.
o kill __P and most of the old K&R prototypes just to be mean.
o minor other nits
Don't arbitrarily limit the initiator ID of the card to something <= 7.
Fix a bug in the checksum code that would incorrectly prevent a valid
checksum of zero. (cp)
Don't touch rely on seeprom data when configuring termination. We may
not have seeprom data. (cp)
Treat all ULTRA2 capable adapters the same way when reading or writing
the BRDCTL register. We previously only did this correctly for aic7890/91
chips. This should correct some problems with termination settings on
aic7896/97 adapters. (cp)
Changes marked with "(cp)"
Pointed out by: Chuck Paterson <cp@bsdi.com>
Also, optimize out a mess of #if's that were duplicating work already
done by config(8). For example, if a file is marked as
"dev/sound/pci/foo.c optional pcm pci" then it's only added if pcm *and*
pci are present, so #if NPCM > 0 and #if NPCI > 0 are totally redundant.
A bit more work is still needed.
Discussed with: cg (a few weeks ago)
aic7xxx.c:
Add a function for sucking firmware out of the controller
prior to reset.
Remove some inline bloat from functions that should not have
been inlined.
During initialization, wait 1ms after the chip reset before
touching any registers. You can get machine checks on certain
architectures (Atari I think?) without the delay.
Return CAM_REQ_CMP for external BDR requests instead
of CAM_BDR_SENT.
Bump some messages to bootverbose levels above 1.
Don't clear any negotiated sync rate if the target rejects
a WDTR message. The sync rate is only cleared if the target
accepts a WDTR message.
Fix a small bug in the mesgin handling code that could cause
us to believe that we had recieved a message that was actually
received by another target. This could only confuse us in
some very rare transmission negotiation scenarios.
Remove some unecessary cleanup of residual information after
a residual is reported. The sequencer does this when the
command is queued now.
that the read EEPROM command has time to execute.
I didn't observe any difference in behavior on my test system but
this is the documented "correct behavior".
We now correctly skip boards that have PnP support enabled, or are in
test mode. The 3c509s support a number of combinations of device
probing, as per the databook.
- ISA only
- PnP only
- ISA or PnP
We will allow cards that can be dealt with by PnP to be attached by the
PnP enumerator.
This fixes the bogus detection of boards at weird ioports.
programming practices. It seems that newer fdc chips have an
alternative way of setting the transfer speed (including high speed
modes for floppy tape) that doesn't use the control register (which
we don't support - we use the old way only). So, they (the BIOS
programmers) sometimes leave out the 0x3f6 control register from
the PnP ports descriptor(!!). "Hey, it works with windows, so
what's the problem?" :-( Anyway, this hack tries to compensate
for that. This was discussed with dfr (who did the pnp attachment).
returns "0" on failure, which is indistinguishable from (say) irq 0. This
should stop a couple of stray messages that turn up.
Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to
a normal interrupt. This might help pccard folks with a shared slot
interrupt. This whole thing needs to be revisited.
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
joystick port on PnP sound cards that have a suitable device ID on them.
Doug Rabson added timer code so it didn't have to beat on the isa timer.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
mutate some panics to kasserts
add more spl protection
PR: kern/14990
Partially Submitted by: Vladimir N.Silyaev <vns@delta.odessa.ua>
Reviewed by: dfr
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
by identifying the version in the PCI drivers.
The OHCI driver just presets this to 1.0 as it is not specified in the
PCI registers anywhere. This should be revisited once USB 2.0 is in
wide spread use.
are queued. Traverse the queues vertically and then horizontally.
This means that TDs for one xfer are transmitted back to back until the
first NAK or error condition. Up to now we transmitted a TD per frame
and transmitted the next TD in the next frame.
The old approach is more fair if you have the end of the queue point at
the beginning of the control transfer queue, but also a lot more overhead
due to the fact that the QHs have to be read more often.
The new approach squirts the packets down the line as fast as possible
for one transfer and then does the next one. In the current situation,
with fairly empty USB buses, this is a more sensible approach. We might
have to revisit the scheduler later however.
It speeds up large transfers (Zip drive, Host-To-Host adapters) on UHCI
by a factor of 5 and makes it as fast as OHCI on the bus.
The next problem to solve is the question why the limit is 300kb/s and
not 1000/kb/s (kb == kilobyte).
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
rather than an "it's mine!" so that other newbus-aware drivers can
bid for the device too. This should allow the sym driver to out-bid
the ncr driver for devices it supports without having to modify ncr.c
at all. ncr would then function as a catch-all.
Support for TDK LAC-CF010 by Ichiro Fukuhara
(ichiro@ichiro.org) on kern/8900 ichiro test TDK CF Card on
Opensource matsuri,tokyo and send patch to us. thanx.
On UDMA CRC errors retry operation as it might be a fluke, if not fall
back to PIO mode on the failing drive. If you get alot of these your
cabeling is most likely not good enough.
On HARD error using DMA, retry once using PIO, if it succeds using PIO
fall back to PIO mode on the failing drive.
pcic_attach_sockets. Rework bus width probe mapping and unmapping to
use the newbus bus_{allocate,release}_resource with a rid of 1 to work
on FreeBSD. Remove a few now unneeded #includes.
it would work), or a specialized one. Most of these have been
creatively stolen from pccard_nkb, which in turn stole from isa
showing that generic bus_ versions of bus_{set,get,delete}_resource
might be profitable.
Fix a couple of minor bugs introduced in the last round of updates
from NetBSD.
Start on the pccard_ivar structure which will hold the resources and
slot number.
Add tcic as a possible attachment for pccard and rename the attachment
for pcicx to pcic since the name has changed since I originally wrote
this stuff.
Next up:
stringing together the various memory and I/O
allocation/mapping primitives in i82365.c, final touches on the isa
attach routine and other fun stuff in that line of attach.
socket attach code. We now have at least a chance for pccard devices
appearing in the future.
This is a snapshot of ongoing work. Proceed at your own risk.
- more req[uest]->xfer changes.
- get the corresponding NetBSD Id's right
ohci.c
- move untimeout above print statement
- remove usb_delay that panics the system (tsleep in intr context) when
ohcidebug > 5.
ugen.c
- create the devices for endpoints with make_dev.
uhub.c
- change from using usbdebug to uhubdebug
- add more debugging statements
X server, is not responding to the VT switching protocol. (This part
of the code has been somewhat wrong in -CURRENT, but -STABLE has the
correct code...)
PCI SCSI controllers. This driver also supports the following Symbios/LSI
PCI SCSI chips: 53C810A, 53C825A, 53C860, 53C875, 53C876, 53C885, 53C895.
However, it does NOT support earlier chips as the following ones: 53C810,
53C815, 53C825.
See README.sym for more details.
Submitted-by: Gerard Roudier <groudier@club-internet.fr>
Add MD_ROOT and MD_ROOT_SIZE options to the md driver.
Make the md driver handle MFS_ROOT and MFS_ROOT_SIZE options for compatibility.
Add md driver to GENERIC, PCCARD and LINT.
This is a cleanup which removes the need for some of the worse hacks in
MFS: We really want to have a rootvnode but MFS on a preloaded image
doesn't really have one. md is a true device, so it is less trouble.
This has been tested with make release, and if people remember to add
the "md" pseudo-device to their kernels, PicoBSD should be just fine
as well. If people have no other use for MFS, it can be removed from
the kernel.
- Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing
the initial work here. One thing I changed was to have the attach
and detach routines work like the PCI drivers, which means that in
theory you should be able to load and unload the driver like the PCI
NIC drivers, however the pccard support for this hasn't settled down
yet so it doesn't quite work. Once the pccard work is done, I'll have
to revisit this.
- Add device wi0 to PCCARD. If we're lucky, people should be able to
install via their WaveLAN cards now.
- Add support for signal strength caching. The wicontrol utility has
also been updated to allow zeroing and displaying the signal strength
cache.
- Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko.
Currently this module is only built for the i386 platform, though once
the pccard stuff is done it should be able to work on the alpha too.
(Theoretically you should be able to plug one of the WaveLAN/IEEE ISA
cards into an alpha with an ISA slot, but we'll see how that turns out.
- Update LINT to use only device wi0. There is no true ISA version of
the WaveLAN/IEEE so we'll never use an ISA attachment.
- Update files.i386 so that if_wi is dependent on card.
pci_probe_nomatch, so it won't be in the way when loading USB as a module.
The reason for them being there in the first place is that every
motherboard comes with USB kit and this way it looks more pretty (peter).
The real solution will be to define some method of detaching a driver
after it has attached.
and shiny usbd daemon to handle events.
usb_port.h:
- Add a macro to retrieve the unit number from a USBBASEDEVICE
usb.h, usb_subr.c:
- Add fields to the device_info struct.
usb_subr.c:
- Fill in the new fields.
- Remove the notification of the event up a bit to make sure all the
information is still available to fill the usb_devinfo struct.
This requires recompilation of usbdevs (src/usr.sbin/usbdevs) and the
ezdownload/ezupload (ports/misc/ezload) utilities in any case.
of queue entries have to be at least 16 bits now! If we're running
a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix
typo in checking against 2200 F/W revision. Slightly fix/reorder fabric
login stuff. Change to usage of isp_getrqentry for code clarity. Add some
defensive dual bus assumptions. Various cleanups, etc...
Role the core version minor number. Change the arguments to the dma
setup function to use a u_int16_t for the output request loop pointer
(truly amazing that this hasn't blown up in anyones face so far). Do
some shuffling around of some items.
by Qlogic. The firmware is now also kept from compiling by default
unless some config options are set.
While we're at it, roll the 2200 f/w to 2.01.0. Still need to get the
1.17.26 2100 f/w working as it solves a lot of problems but it doesn't
want to work yet with this driver (:-)).
out of the PCI CLASS reg and store it in the softc. Use the getenv_quad
function to get a WWN override from the environment. Look for a config
value for same. Make slightly less lame the wwn seed construction.
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
o Delete pcic1 from NEWCARD
o Add explicit resource hints to pcic0
o Get attach working with newbus, kinda (it does all the newbus stuff,
but doesn't try to attach the pccard yet, too many panics).
o Disable ie0 and le0 in NEWCARD config. There appears to be a bug in
the isa_compat code wrt memory conflicts with newbus drivers for
reasons unknown.
o Minor cleanups.
ES1371 and ES1373 PCI Audio Sound Chips.
The 1371 and 1373 can be found on newer CreativeLabs/Ensoniq
sound cards such as the SoundBlaster PCI 16,64 and 128.
Submitted by: Russell Cattelan <cattelan@thebarn.com>
Obtained from: Parts obtained from linux, but rewritten by Russell
Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c)
Make sio work for pccard here - pccardd doesn't activate interrupts
until after prove has succeeded.
Mark the initial reset of likely sio ports as broken as it depended on
config supplying a list of locations to probe, devices are now proved
standalone.
Optimize a bit of COM_NOAST4() logic.
Use bus_get_resource_start() etc rather than using isa-centric calls.
Reactivate the IIR_TXRDYBUG test, I've got a card here with it.
Try to be a bit smarter about activating interrupts (ie: don't panic
if polled)
Fix some style bugs that have crept in over time (there are still more).
Don't use NFDC as an arbitary limit, it is not required and goes against
using PnP fdc devices (eg: when PNPBIOS is turned on, the motherboard
devices (sio, fdc, etc etc) are detected via PnP, not config(8).)
o Rewrite probe code to work in the newbus world.
o Add preliminary pnp support. I have no clue what the pnp ids for
the older ISA machines/cards. I don't have any of these cards/machines
so I'll have to rely on the user community to give me help.
o Minor code reformatting.
Attach hasn't been touched, and there may be some config issues that
we need to deal with as well. These will follow in time.
Cleaning up the code:
- Declare many functions static
- Change variable names to make them more self explanatory
- Change usbd_request_handle -> usbd_xfer_handle
- Syntactical changes
- Remove some unused code
- Other KNF changes
Interrupt context handling
- Change delay to usbd_delay_ms were possible (takes polling mode into
account)
- Change detection mechanism for interrupt context
Add support for pre-allocation DMA-able memory by device driver
Add preliminary support for isochronous to the UHCI driver (not for OHCI
yet).
usb.c, uhci.c, ohci.c
- Initial attempt at detachable USB host controllers
- Handle the use_polling flag with a lttle more care and only set it if
we are cold booting.
usb.c, uhci.c ohci.c, usbdi.c usbdi_util.c usb_subr.c
- Make sure an aborted pipe is marked as not running.
- Start queued request in the right order.
- Insert some more DIAGNOSTIC sanity checks.
- Remove (almost) unused definitions USBD_XFER_OUT and USBD_XFER_IN.
usb.c, usb_subr.c
- Add an event mechanism so that a userland process can watch devices
come and go.
ohci.c
- Handle the case when a USB transfer is so long that it crosses two
page (4K) boundaries. OHCI cannot do that with a single TD so we make
a chain.
ulpt.c
- Use a bigger buffer when transferring data.
- Pre-allocate the DMA buffer. This makes the driver slightly more
efficient.
- Comment out the GET_DEVICE_ID code, because for some unknown reason it
causes printing to fail sometimes.
usb.h
- Add a macro to extract the isoc type.
- Add a macro to check whether the routine has been entered after splusb
and if not, complain.
usbdi.c
- Fix a glitch in dequeueing and aborting requests on interrupt pipes.
- Add a flag in the request to determine if the data copying is done by
the driver or the usbdi layer.
Without this, ioctl commands for setting formats and speeds were
essentially ignored for simplex devices until the application actually
performed a read or write.
* Make sure that both channels are set in the SB mixer code and provide a
mixer table specifically for the ess18xx which supports the extended
accuracy available on this part.
* Fix a stupid bug in ess_format() which ignored the passed-in format and
changed the hardware based on the value which was set last time. This
meant that the hardware setting was often not set correctly at all.
* Add a custom identify driver for the ESS1888 which automagically detects
and adds the device in a pseudo-PnP way. This driver also emits the magic
sequence which enables the sound hardware after a hard reset, allowing
it to work correctly for the sound hardware of a PWS 433au (and probably
all other PWS class alpha machines).
With these changes, I was able to play back simple sounds on my 433au. I
have not tested recording or any other formats other than 8bit ulaw and
16bit stereo.
Make tuner on French SECAM Hauppauge cards work
Submitted by: Cyrille Lefevre <clefevre@citeweb.net>
Fix clipping bugs ready for Xv support in XFree86 4.0
Submitted by: Thomas Mueller <tmueller@thmu.de>
Fix the 'feature' where /dev/vbi needed to be opened before /dev/bktr
when using Teletext with Alevt and FXTV.
Requested by: Randall Hopper
Rename a few (I wish companies would stop buying each other)
Add a quirk entry for hubs that say they are self powered but are
in fact bus powered (usage in uhub follows shortly).
condition for Short transfers.
Change the scheduling to Depth first. We now transfer as many TD's as
possible from QH before moving to the next queue (Breadth first). It should
still be verified that this does not lead to starvation in a busy system
(in the case were transfers are added to the beginning of the control
or bulk queues).
It however posts a bogus button up event once in a while. Whenever
we receive dx=dy=dz=buttons=0 we postpone adding it to the queue for
50msecs with a timeout. If in the meantime something else is posted
the event is ignored.
This avoids the problem Nik Sayer reported. He noticed that X windows
would drop and pick up a window once in a while.
Thanks, Nik, for supplying me with the keyboard to fix the problem!
Try to use a 32bit mask on the IO addresses, this fixes the alpha
and hopefully doesn't break on any i386 machines.
Try to enable both read & write cache on disks, they should be as
default, but better be sure..
Fix a bug which could cause panics in ad/atapi-interrupt.
Add support for UDMA66 on Promise Ultra/Fasttrak controllers.
Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead.
Add a delay in the dump routine in ata-disk.c, some controllers
seem to need this. Also dont use the timeout watchdog when dumping.
Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA
for those that has HW that works.
Add support for some not-up-to-spec ATAPI devices that returns data
together with completition status on data moving cmd's.
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
test this support since I don't have the dongle for the card in
question and the dongle I have for my 3C589D doesn't seem to work on
it. I don't know if this is due to the damage I did to the 562 card
in transit from freebsdcon, or a mis-matched dongle...
Update AverMedia GPIO values
Submitted by: AverMedia
Add support for WinTV Theater Dolby Surround Sound DPL3518A chip
Submitted by: Frank Nobis <fn@radio-do.de>
Make PLL mode the default for Bt878s. You no longer need options BKTR_USE_PLL
pccard attachments must activate the resources they want to access.
ep didn't do this, so of course thee eeprom came back as busy. ed and
sio already did this. It was only due to a bug in the logic that the
probe succeeded. These problems have been fixed.
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
Shift to using the same queueing strategy that the amr driver uses.
Some simple tests indicate that we use about 2% of the CPU at around
500tps with the controller completely saturated with I/O.
the time spent at splbio(). We now avoid it unless we are actually
manipulating the command queues themselves. This doesn't improve
performance noticeably, but should improve concurrency somewhat.
(yet) compile and link. Renamed pcic back to pcic from pcicx, but
conditionalize its inclusion on pccard being included also. card is
the old and pccard is the new, which is a handy way to have both in
the tree at the same time.
Obtained from: newconfig project
More to follow...
incomplete and likely has problem. The code was originally pcmcia,
but I renamed it to pccard and made it compile on FreeBSD -current. I
converted SIMPLEQ to STAILQ as well as a few sc->dev.xname ->
device_printf changes. This is a green port of fairly mature code.
I derived this work from the FreeBSD newconfig project
(http://www.jp.freebsd.org/newconfig). Any problems with it are
likely introduced by me.
Obtained from: newconfig project
if_fe.c uses PCCARD_MODULE() and is part of GENERIC. I've #ifdef'ed out
the #include of "card.h" to hopefully disable pccard support in this
driver until it can be converted. I'm not positive this will fix make
release, but it can't possibly make it any worse than it is now.
I hope this stuff settles down soon.
yet, but that should be resolved shortly. Non memory mapped ed
devices should work, but I cannot test this since my only ed card is
memory mapped.
Submitted by: Matt Dodd <mdodd@freebsd.org>
I'm committing this from a laptop running this driver. Have only one
devclass for all ep devices (at least for pccard and eisa) so unit
numbering is sane. Might not work with both isa and non-isa devices
on the same system until ep is updated (Matt has some patches in the
pipeline which should resolve this, he wanted me to commit this so he
can resolve any conflicts against cvs rather than my patches).
Reviewed by: Matt Dodd <mdodd@freebsd.org>
by Peter Wemm, but I've not merged all the changes he sent to me yet.
This has not been reviewed by bde, so I'm committing to resolve any
issues he has with this when he returns from FreeBSD CON 99.
I've had four reports of this working for them. I've been able to
communicate to both my built in modem and a pccard modem with these
patches.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
it has the same value on all platforms. Previously it was just under
3 seconds on x86 (typically hz<=128) and just under 1/3 of a second on
alpha (typically hz>=1024). This covers up a race between ad_interrupt()
and ad_timeout() which is being looked into.
reviewd by: sos
bootup. Somehow my backout of an abortaive attempt at shared
memory autoconfiguration included this line:
sc->mem_shared = 1;
Which is fairly important as it turns out.
Since I performed my pre-commit testing on a different box with a generic
NE2000 I didn't catch this. Pointy hat.
Put splbio protection around the main launch loop. We've seen cases where
the bottom half was cutting off the branch on which we're sitting.
Experienced-by: Michael Reifenberger <root@nihil.plaut.de>
have you is prototyped). Removed code versions in md struct- not used
any more. Allocate transfer dma maps and xflist stuff in mbxdmasetup based
upon isp->isp_maxcmds. Allow for multiple calls to mbxdmasetup (for
isp_reset cases).
file later. Do some pencil-sharpening types of minor changes. Change
how active commands are remembered (using new inline functions to get
handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as
outgoing mailbox 2 will tell you the f/w's notion of the max commands
that can be supported. Attempt to retrieve loop topology. Add in the
appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little
Endian machines but is needed for sparc (on other platforms)). Move
the temp port database we use to find out where things have moved to
after a LIP to the softc and off the kernel stack. Follow Qlogic's
hint and don't bother setting a tag for commands that don't have
this enabled (presumably the f/w will do it's own selection then).
Use an INT_PENDING macro to check for an interrupt. The call to
ISP_DMAFREE now just takes the handle- not the 'handle-1' which was
a layering violation. Use CFGPRINTF in a couple of places to make
things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
where it defaults to one. Change simq width allocation to the max number
of commands supported by the HBA after f/w fires up- not the constant
MAXISPREQUEST value. Do some stylistic changes.
Add in null SWIZZLE definitions. Add in CFGPRINTF define. Change default
debug level to refer to an external isp_debug variable. Remove inline
functions as they're now in isp_inline.h and include that file.
the result queue length is never less than 64. Move (ick) temp port
database used for post-LIP merging off the kernel stack and put it
into the softc. Remove some target mode stuff which will come back
later in a different file. Change how the list of outstanding commands
are stored (now allocated at mailbox setup time to be just enough for
the max for a specific HBA which can vary). Keep a rotating seed of
the last index for this in the softc. Increase the count of active
commands from 10 to 16 bits.
- Generally clean things up.
- PnP now supported.
Will convert to bus_space, ifmedia and add a DEVICE_IDENTIFY() method
for autodetection. As it stands
device ex0 at isa0
should find a card if one is present.
I feel less dirty now.
In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
32 bytes is safe.
Handle successful completion of message log retrieval commands.
With these changes, the driver correctly handles the consequences of drive
death and replacement in a reliable array. Note that the massive backlog
of I/O during handling of such an event can kill the system if softupdates
is enabled.
Without it the kernel config options, like OVERRIDE_TUNER, where not
getting passed to the driver.
Bug noticed by: Marc Fonvieille <fonvi@club-internet.fr>
now lives in the respective bus front end files.
- Add various function prototypes to if_edvar.h
- Clean up some debugging code that snuck into if_ed_isa.c
- Turn on the right bits in files.i386
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
PJ cards. This will probably also support the AcceleRAID and
eXtremeRAID cards, but nobody has volunteered one for testing, so I
haven't enabled their PCI device IDs.
Slightly clean up communication between the disk devices and the
controller device as per new practice, and move some more register-
related items int mlxreg.h from mlxvar.h.
Remove some unnecessary read-modify-write operations to the card
control registers; they don't behave like that.
Increase the status polling interval to 10 seconds. It's still possible
to load the card up to the point where a status poll will find the
previous poll still running, but this will reduce the incidence of
complaints.
maximum of 64 kB.
vinum_conf, struct drive: add fields for the current number of active
requests and the maximum ever active.
struct sd: Add fields for initialize progress.
struct mc: set the size of saved file names to MCFILENAMELEN instead
of the previous explicit constant.
limit the number of outstanding requests on a specific drive and
overall.
Change the way we set the active request count. This enables us to
start the requests without being in splbio for the duration, which
could be very long for IDE drives in PIO mode.
context. Be prepared to fail instead.
MMalloc, FFree: ensure that saved file names are properly terminated.
Use MCFILENAMELEN instead of the previous explicit constant.
and then doing it itself, resulting in a panic downed drives.
Sleuth-work-by: Christopher Masto <chris@netmonger.net>
Remove dummy function initsd, which is now (implemented) in
vinumrevive.c
vinum_scandisk: Check that a drive is up before reading from it. This
is probably excessive paranoia.
Rather than teaching pci_ioctl about hoses, we just pass down a magic number
& let the platform code figure out what the hose is based on what the bus
number is.
concept approved by dfr
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
their HotRod controller and on SIIG PCI ultra DMA controller. These
changes also made lots of the Promise code go away, its all much more
generic this way.
Get rid of atapi_immed_cmd, instead use the queue to move atapi commands
from interrupt context if nessesary, the entire atapi layer has
gotten an overhaul.
Lots of fixes to utililize the new features in subr_disk.c etc, and
get rid of the last biots of softc arrays in the drivers, the
only one left is atadevices which cannot easily go away (yet).
Use our own malloc names, its a lot easier to track memory usage this way.
General cleanup overall.
- Work around a problem not yet solved in the tree (but solved in mine.)
device_get_ivars() should never be cast to a struct resource_list *
The solution, under review, involves the creation of a
device_get_resource_list() function. More later.
configuration information from a DPT card at a given port.
This is needed by the ISA bus front end (still to come) and the EISA
bus front end (which hasn't ever worked).
- Blow away dpt_eisa.h as the information it contains does not justify
an additional file.
- Convert dpt_eisa.c to use the onboard config instead of trying to
read the EISA configuration registers.
- Some cleanup and improvements in the uhci and ohci drivers
- Support for plugging and unplugging devices improved
- Now available is bulk transport over OHCI controllers
- Resume and suspend have been temporarily been disabled again. Proper
support for it is available in the uhci.c and ohci.c files but I have
not yet spent the brain cycles to use it.
- OpenBSD now uses the USB stack as well
- Add FreeBSD tags
Remove the use of ukbd_disconnect and replace it with direct
calls to disable.
Change printf to DPRINTF
Remove the use of usbd_lock, change it to splusb()/splx()
the AMI PCI controllers using the 8LD firmware interface (40LD firmware
will be supported as soon as I have hardware to test with).
These controllers are rebadged by Dell as the PERC, as well as by HP
and possibly other vendors.
The old algorithm was:
if class == storage and subclass != SCSI device must be IDE
This results in claiming 'raid' and 'other' storage devices as IDE,
which is typically not the case.
Reviewed by: sos
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
0x8024b04e) so that the cards description is used instead of overriding
it. While I'm here, add an ID for the SUP2080 and the SUP2030.
PR: kern/13983
Submitted by: Kurt D. Zeilenga <Kurt@OpenLDAP.Org> (SUP2030)
dfr (rest of change)
Reviewed by: dfr
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Reviewed by: dfr
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
Add debuging for all failure cases in aha_cmd().
Always check DATAIN_REG_READY even if we're ready to exit the
read loop.
The last fix allows the AHA-1640 MCA SCSI adapter to operate
correctly and likely fixes problems on a few other oddball
adapters. (I suspect my Dell Drive Array in 1540 mode needs this.)
Reviewed by: Warner Losh
apm_saver uses the apm_display() routine from the apm system to
"suspend" the "display" part of the machine.
This is beneficial for some laptops (or other machines with
non-traditional displays) that choke on the 'green' saver's
effect.
Another way of looking at this is that it's the same as a screen
saver that does an 'apm -d 0' to blank the display and an 'apm -d 1'
to bring it back. One probably ought to use these commands to make
sure the effect will be correct before using it unattended.
For unknown devices the output will now be
pci0: unknown card (vendor=0x109e, dev=0x0878) at 14.1 irq 19
instead of
pci0: unknown card DD^0878 (vendor=0x109e, dev=0x0878) at 14.1 irq 19
Before this change, the code used to take the PCI vendor id and translate it
into a three letter ASCII name.
For PnP devices, the vendor id _does_ map to a nice ASCII name
(eg Creative Labs PnP ID maps to "CTL", ESS PnP ID maps to "ESS")
But there is no such mapping for PCI devices, as can be seen by the
example above where the Brooktree PCI vendor ID maps to "DD^"
The PCI Special Interest Group confirmed they do not have any mappings
from vendor ID to ASCII.
and/or when using the card.
o Convert the driver to using bus_space. This allows alphas with
fxp's to boot, rather than panic'ing because rman_get_virtual()
doesn't really return a virtual address on alphas.
o Fix an alpha unaligned access error caused by some misfeature of
gcc/egcs: if link_addr & rbd_addr in the fxp_rfa struct are 32 bit
quantities, egcs will assume they are naturally aligned. So it will do
a ldl & some shifty/masky to twiddle 16 bit values in fxp_lwcopy().
However, if they are 16-bit aligned, the ldl will actually be done on
a 16-bit aligned value & we will panic with an unaligned access
error... Changing their definition to an array of chars seems to fix
this. I obtained this from NetBSD.
I've tested this on both i386 & alpha.
of parity check and rebuild operations. This enables us
to stop the operation and restart at a later time.
enum parityop: Trivial enum to decide what parityops() is going to do.
could stand.
Define the correct return lengths for a number of ioctls.
Add ioctls VINUM_CHECKPARITY and VINUM_RESETPARITY, still to be fully
implemented.
ourselves. This breaks a vicious circle which caused
vinum to dereference a null vp if device nodes were
missing.
Reported-by: Brad Chisholm <sasblc@unx.sas.com>
Alec Wolman <wolman@cs.washington.edu>
check_drive: Don't take a drive down if it's only referenced.
read_drive: Remove unused variable.
get_empty_volume: initialize plexes to -1 (not allocated)
remove_drive_entry:
Remove recurse parameter (there's nothing below a drive in the hierarchy).
Use remove_sd_entry to remove sds, don't do it ourselves.
Log errors, don't throw rude remarks.
remove_plex_entry:
Don't use plex->subdisks as a loop limit, it gets changed in the
loop. This caused some removals to only remove half the subdisks.
Change logging of some "impossible" situations.
remove_volume_entry:
Use remove_plex_entry to remove plexes, don't do it ourselves.
update_sd_config:
Use set_sd_state to do the work.
will have to mknod yourself for now.
* don't eat the first write()
* partial rvplayer fix- don't panic on unaligned writes unless our
feeder chain requires them for downconversion. a fuller fix is
on the way.
I386_BUS_SPACE_IO. Compiles now on the Alpha, but likely will not
work due to bus space address <-> virtual address mapping bogons that
work for i386 but not alpha.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
Leadtek Winfast 2000 cards.
No audio support yet, just the card make is reported.
Submitted by: Craig <crh@outpost.co.nz>
Submitted by: Peter Wemm <peter@netplex.com.au>
BUF_LOCKFREE a buffer prior to physically freeing it. While these
bugs did not cause a crash, they might in the future.
Added eof handling for unlabeled partitions.
Submitted by: Tor.Egge@fast.no
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
Enhance MIRROR code. Add a few more sanity checks and implement
a zone-based disk selector to make use of both disks when reading.
Also implement a read fail-over. If a read error occurs on one
disk, the I/O is retried on the other.
NOTE: CCD's mirroring support cannot deal with write errors properly
in regards to recovery, meaning that 'old' data under a write error may
be read non-deterministically if you reboot after a write error, and CCD
certainly cannot deal with a disk changeout. And it still can't. Use
vinum if you are really serious about mirroring. CCD basically just
implements a poor-man's mirror.
sum the total amount of I/O issued to determine when all the I/O
has completed. This fails when the EOF boundry occurs in the middle
of an I/O. Using cbp->cb_buf.b_bufsize works better.
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
size != 512 that are configured without a label. The bug should only
have effected swap-backed VN mounts without a label.
Add several major features to VN. In the kernel we add a swap
pre-reservation capability, which can be used to guarentee seek
consistency for swap-backed VN nodes. This also incidently allows
a swap-backed VN filesystem to be recovered after a crash in some
cases (if the same swap blocks happen to be reserved).
We also add a number of new options to vnconfig which do the work
of pre-zeroing or creating/truncating/extending a file which greatly
simplifies using VN in a file-backed configuration.
Add FreeBSD CVS label to sys/sys/vnioctl.h, as well as a new ioctl
flag for the swap pre-reservation feature.
Reviewed by: Alan Cox <alc@cs.rice.edu>, David Greenman <dg@root.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
