After controller updates control word in a RX LE, driver converts
it to host byte order. The checksum value in the control word is
stored in big endian form by controller. r205091 didn't account for
the host byte order conversion such that the checksum value was
incorrectly interpreted on big endian architectures which in turn
made all TCP/UDP frames dropped. Make RX checksum offload work
on any architectures by swapping the checksum value.
Reported by: Sreekanth M. ( kanthms <> netlogicmicro dot com )
Tested by: Sreekanth M. ( kanthms <> netlogicmicro dot com )
supposed to be APs and the later 24 are pre-configured as STAs. A wrong
condition during initialization is responsible for not configuring the last
8 array members. This is results in being able to create more than 8,
possible uninitialized, AP-VAPs.
PR: kern/153549
Submitted by: Erik Fonnesbeck <efonnes at gmail.com>
MFC after: 2 weeks
The controller is commonly found on DM&P Vortex86 x86 SoC. The
driver supports all hardware features except flow control. The
flow control was intentionally disabled due to silicon bug.
DM&P Electronics, Inc. provided all necessary information including
sample board to write driver and answered many questions I had.
Many thanks for their support of FreeBSD.
H/W donated by: DM&P Electronics, Inc.
modification of memory which was already free'd and eventually in:
wpi0: could not map mbuf (error 12)
wpi0: wpi_rx_intr: bus_dmamap_load failed, error 12
and an usuable device.
PR: kern/144898
MFC after: 3 days
md(4) to using M_WAITOK malloc calls.
M_NOWAITOK allocations may fail when enough memory could be freed, but not
immediately. E.g. SU UFS becomes quite unhappy when metadata write return
error, that would happen for failed malloc() call.
Reported and tested by: pho
MFC after: 1 week
table is present, then the acpi_ec(4) driver will allocate its resources
from nexus0 before the acpi0 device reserves resources for child devices.
Reviewed by: jkim
manual 1000BASE-T modes of DP83865 only work together with other National
Semiconductor PHYs.
- Spell 10BASE-T correctly
- Remove some redundant braces.
condition in proc_rwmem() and to (2) simplify the implementation of the
cxgb driver's vm_fault_hold_user_pages(). Specifically, in proc_rwmem()
the requested read or write could fail because the targeted page could be
reclaimed between the calls to vm_fault() and vm_page_hold().
In collaboration with: kib@
MFC after: 6 weeks
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
controller with Card Read Host Controller. These controllers are
multi-function devices and have the same ethernet core of
JMC250/JMC260. Starting from REVFM 5(chip full mask revision)
controllers have the following features.
o eFuse support
o PCD(Packet Completion Deferring)
o More advanced PHY power saving
Because these controllers started to use eFuse, station address
modified by driver is permanent as if it was written to EEPROM. If
you have to change station address please save your controller
default address to safe place before reprogramming it. There is no
way to restore factory default station address.
Many thanks to JMicron for continuing to support FreeBSD.
HW donated by: JMicron
a 2GHz channel with appropriate flags set to sc->config. Due to not zeroing
sc->config for auth/assoc those flags are still set while trying to connect
on a 5GHz channel.
MFC after: 3 days
Use pci_enable_busmaster instead of setting PCIM_CMD_BUSMASTEREN
directly. There's no need to set PCIM_CMD_MEMEN. The bit is set when a
SYS_RES_MEMORY resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Write 1 byte instead of 4 when setting the HIFN_TRDY_TIMEOUT register.
It is only 1 byte according to the specification.
Reviewed by: jhb
Approved by: kib (mentor)
configuration registers directly.
Remove pci_enable_io calls where they are redundant. The PCI bus driver
will set the right bits when the corresponding bus resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Reviewed by: jhb
Approved by: kib (mentor)
This is based on the patch submitted by Yuri Skripachov.
Overview of the changes:
- clarify double-use of some ACPI_BATT_STAT_* definitions
- clean up undefined/extended status bits returned by _BST
- warn about charging+discharging bits being set at the same time
PR: kern/124744
Submitted by: Yuri Skripachov <y.skripachov@gmail.com>
Tested by: Yuri Skripachov <y.skripachov@gmail.com>
MFC after: 2 weeks
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.
delete the IRQ resource from the psmcpnp device completely.
- Don't allocate the IRQ resource shared. It is not a shareable interrupt
on ISA. The bus driver can set RF_SHAREABLE if the IRQ is actually
shareable on a non-ISA bus.
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
function always returned the nominal frequency instead of current frequency
because we use RDTSC instruction to calculate difference in CPU ticks, which
is supposedly constant for the case. Now we support cpu_get_nominal_mhz()
for the case, instead. Note it should be just enough for most usage cases
because cpu_est_clockrate() is often times abused to find maximum frequency
of the processor.
There is no need to use an atomic operation at structure initialization
time.
Note that the file changed is not connected to the build at this time.
Reviewed by: jhb (general issue)
Approved by: np
MFC after: 2 weeks
Prior to this change, the addressing method wasn't getting set, and
so the LUN field could be set incorrectly in some instances.
This fix should allow for LUN numbers up to 16777215 (and return an error
for anything larger, which wouldn't fit into the flat addressing model).
Submitted by: scottl (in part)
This bug manifested itself after repeated device arrivals and
departures. The root of the problem was that the last entry in the
reply array wasn't initialized/allocated. So every time we got
around to that event, we had a bogus address.
There were a couple more problems with the code that are also fixed:
- The reply mechanism was being treated as sequential (indexed by
sc->replycurindex) even though the spec says that the driver
should use the ReplyFrameAddress field of the post queue
descriptor to figure out where the reply is. There is no
guarantee that the reply descriptors will be used in sequential
order.
- The second word of the reply post queue descriptor wasn't being
checked in mps_intr_locked() to make sure that it wasn't
0xffffffff. So the driver could potentially come across a
partially DMAed descriptor.
- The number of replies allocated was one less than the actual
size of the queue. Instead, it was the size of the number of
replies that can be used at one time. (Which is one less than
the size of the queue.)
mps.c: When initializing the entries in the reply free
queue, make sure we initialize the full number that
we tell the chip we have (sc->fqdepth), not the
number that can be used at any one time (sc->num_replies).
When allocating replies, make sure we allocate the
number of replies that we've told the chip exist,
not just the number that can be used simultaneously.
Use the ReplyFrameAddress field of the post queue
descriptor to figure out which reply is being
referenced. This is what the spec says to do, and
the spec doesn't guarantee that the replies will be
used in order.
Put a check in to verify that the reply address passed
back from the card is valid. (Panic if it isn't, we'll
panic when we try to deference the reply pointer in any
case.)
In mps_intr_locked(), verify that the second word of the
post queue descriptor is not 0xffffffff in addition to
verifying that the unused flag is not set, so we can
make sure we didn't get a partially DMAed descriptor.
Remove references to sc->replycurindex, it isn't needed
now.
mpsvar.h: Remove replycurindex from the softc, it isn't needed now.
Reviewed by: scottl
functionality is the same, a difference is that the DS1775 has a better
precision than the LM75. But we do not use it in our setup. Make the
LM75 work the same as the DS1775.
Fix a typo in device_set_desc.
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
pointer where data is to be returned by ibask() (currently unimplemented),
while __retval holds the value returned by the libgpib ibfoo() functions.
The confusion resulted in the ibfoo() functions returning an uninitialized
value except in situations where the GPIB activity has been terminated
abnormally.
MFC after: 3 days
re-arming the watchdog timeout.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
AX88772 controllers. ASIX added a new feature for AX88178/AX88772
controllers which allows combining multiple TX frames into a single
big frame. This was to overcome one of USB limitation where it
can't generate more than 8k interrupts/sec which in turn means USB
ethernet controllers can not send more than 8k packets per second.
Using ASIX's feature greatly enhanced TX performance(more than 3~4
times) compared to 7.x driver. However it seems r184610 removed
boundary checking for buffered frames which in turn caused
instability issues under certain conditions. In addition, using
ASIX's feature triggered another issue which made USB controller
hang under certain conditions. Restarting ethernet controller
didn't help under this hang condition and unplugging and replugging
the controller was the only solution. I believe there is a silicon
bug in TX frame combining feature on AX88178/AX88772 controllers.
To address these issues, reintroduce the boundary checking for both
AX88178 and AX88772 after copying a frame to USB buffer and do not
use ASIX's multiple frame combining feature. Instead, use USB
controller's multi-frame transmit capability to enhance TX
performance as suggested by Hans[1].
This should fix a long standing axe(4) instability issues reported
on AX88772 and AX88178 controllers. While I'm here remove
unnecessary TX frame length check since upper stack always
guarantee the size of a frame to be less than MCLBYTES.
Special thanks to Derrick Brashear who tried numerous patches
during last 4 months and waited real fix with patience. Without
this enthusiastic support, patience and H/W donation I couldn't fix
it since I was not able to trigger the issue on my box.
Suggested by: hselasky [1]
Tested by: Derrick Brashear (shadow <> gmail dot com>
H/W donated by: Derrick Brashear (shadow <> gmail dot com>
PR: usb/140883
isn't configurable in a meaningful way. This is for ifconfig(8) or
other tools not to change code whenever IFT_USB-like interfaces are
registered at the interface list.
Reviewed by: brooks
No objections: gavin, jkim
looking to see if there is an existing IRQ resource for a given IRQ
provided by the BIOS and using that RID if so. Otherwise, allocate a new
RID for the new IRQ.
Reviewed by: mav (a while ago)
max_request_segments * PAGE_SIZE if the I/O is page-aligned; the
largest I/O we can guarantee will work is PAGE_SIZE less than that.
This unbreaks 'diskinfo -t'.
as an association ID is set any scan is supposed to be a background scan.
This implies that the firmware will switch back to the associated channel
after a certain threshold, though, we are not notified about that. We
currently catch this case by a timer which will reset the firmware after
a 'scan timeout', though, upper layers are not notified about that and
will simply hang until manual intervention. Fix this by resetting the
firmware's knowledge about any association on RUN -> ASSOC and
!INIT -> SCAN transitions.
Tested by: Zhihao Yuan <lichray at gmail.com>
MFC after: 1 week
- Do not call iwn_calib_reset() for monitor mode. We do not want to query
information and do runtime calibration while in monitor mode. Poking the
firmware with adjustments for calibration results in firmware asserts.
This could happened on RUN -> RUN transition only.
- Adjust blink rate for monitor mode. It's supposed to not freak out and
turn off after a while.
- While here, remove one useless assignment of calib.state, it gets
overwritten later in the function.
Submitted by: Brandon Gooch <jamesbrandongooch at gmail.com>
MFC after: 1 week
preserve the upper bits of the first data byte.
While here, shorten a few nearby lines.
PR: kern/152768
Reported by: Sascha Wildner saw of online.de
Reviewed by: scottl
MFC after: 1 week
longer requested of the boot firmware. Instead of sending those results
to the runtime firmware the firmware is told to do the DC calibration
itself.
MFC after: 1 week
the size can be smaller than the constant when you are
doing HW TAGGING, and you still need to process this
packet in a normal way. I'm not sure where the notion
to just return came from, but its wrong.
MFC after: 3 days
Second, correct the discard/refresh_mbufs code to behave
more like igb, there have been panics due to discards and
this should fix them.
MFC after: 3 days
finding. The test to compare the mbuf m_len against
a fixed value and then returning needs to be removed.
When using VLANS and doing HW_TAGGING, and IPV6, the
ICMP6 packets actually fail this condition, the constant
assumes that the tag is IN the frame, and its not, so
the length is actually tiny. Furthermore, I'm not sure
what the point was to just return??
MFC after: 3 days
the controller to workaround silicon bug of i82557. Each reset will
re-establish link which in turn triggers MII status change
callback. The callback will try to reconfigure controller if the
controller is not i82557 to enable flow-control. This caused
endless link UP/DOWN when the workaround was enabled on non-i82557
controller.
To fix the issue, apply RX lockup workaround only for i82557.
Previously it blindly checked undocumented EEPROM location such
that it sometimes enabled the workaround for other controllers. At
this time, only i82557 is known to have the silicon bug.
This fixes a regression introduced in r215906 which enabled flow
control support for all controllers except i82557.
Reported by: Karl Denninger (karl <> denninger dot net)
Tested by: Karl Denninger (karl <> denninger dot net)
MFC after: 3 days
or detached. Normally it should be changed through user land ioctl(2)
system calls but it looks there's no apps for USB and no need.
With this patch, libpcap would detect the usbus interfaces correctly and
tcpdump(1) could dump the USB packets into PCAP format with -w option.
However it couldn't print the output to console because there's no
printer-routine at tcpdump(1).
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
versions of FreeBSD. In fact we are already missing a lot of conditional
code necessary to support older versions of FreeBSD, including alternatives
for vital functionality not yet provided by the respective subsystem back
then (see for example r199663). So this change shouldn't actually break
this driver on versions of FreeBSD that were supported before. Besides,
this driver also isn't maintained as an multi-release version outside of
the main repository, so removing the conditional code shouldn't be a
problem in that regard either.
- Sprinkle some more const on tables.
hence existing applications like webcamd are expecting that.
This problem was introduced by SVN change 214221 where cdev=
was replaced by ugen= by accident. Solve this problem by
redefining cdev= in devd notifications.
MFC after 3 days.
Approved by: thompsa (mentor)
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
the dev.fxp.%d.noflow tunable as the same effect can now be achieved with
ifconfig(8) by setting the flowcontrol media option as desired (besides
the tunable never having a chance to actually enable flow control support
so far).
In joint forces with: yongari
- Fix a bug where TCO_BOOT_STS was supposed to be cleared after
TCO_SECOND_TO_STS and not before.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
support multi-queue but the hardware limitation made it hard to
implement supporting multi-queue. Allocating more than necessary
vectors is resource waste and it can be added back when we
implement multi-queue support.
number of retry to be performed whenever controller found RX
descriptor was empty. RX empty interrupt is generated only when the
retry counter is over. Experimentation shows retrying RX descriptor
loading increased number of dropped frames under flow-control
enabled environments so disable it and have controller generate RX
empty interrupt as fast as it can.
While I'm here fix RXCSR_DESC_RT_CNT macro.
(wrong unit number for a host controller) when the module is load /
unloaded repeatly. Attaching the USB pf is moved to usbus device's
attach.
Pointed by: yongari
disable ASPM L0S and L1 LINK states on 82573, 82574,
and 82583. The theory is that this is behind certain
hangs being experienced by some customers.
Also included a small optimization in the rxeof routine
that was in my internal code.
Change the PBA size for pchlan, it was incorrect.
MFC after: 3 days
- Fixes from John Baldwin: vlan shadow tables made per/interface,
make vlan hw setup only happen when capability enabled, and
finally, make a tuneable interrupt rate. Thanks John!
- Tweaked watchdog handling to avoid any false positives, now
detection is in the TX clean path, with only the final check
and init happening in the local timer.
- limit queues to 8 for all devices, with 82576 or 82580 on
larger machines it can get greater than this, and it seems
mostly a resource waste to do so. Even 8 might be high but
it can be manually reduced.
- use 2k, 4k and now 9k clusters based on the MTU size.
- rework the igb_refresh_mbuf() code, its important to
make sure the descriptor is rewritten even when reusing
mbufs since writeback clobbers things.
MFC: in a few days, this delta needs to get to 8.2
Shorten the descriptive strings for Huawei devices. The vendor or
operator name should not be included in the device name.
Submitted by: Emile Coetzee
MFC after: 3 days
- Partially revert r172334; as it turns out the DELAYs in gem_reset_{r,t}x()
are actually necessary although bus space barriers and gem_bitwait() are
used, otherwise the controller may trigger an IOMMU errors on at least
sparc64. This is in line with what Linux and OpenSolaris do.
- Add some DSP init code for BCM5221. The values derived from Apple's GMAC
driver and the same init code also exists in Linux's sungem_phy driver.
- Only read media status bits when they are valid.
Obtained from: NetBSD, OpenBSD
autonegotiation along with manual media selection and also only report flow
control status when BMCR_AUTOEN is set (at least with gentbi(4) determining
the flow control status results in false-positives when not set), use
MIIF_NOMANPAUSE.
autonegotiation along with manual media selection and ukphy_status() also
only reports flow control status when BMCR_AUTOEN is set (at least with
gentbi(4) determining the flow control status results in false-positives
when not set), use MIIF_NOMANPAUSE.
The Myri10GE NIC will assume all TSO frames contain partial checksum,
and will emit TSO segments with bad TCP checksums if a TSO frame
contains a full checksum. The mxge driver takes care to make sure
that TSO is disabled when checksum offload is disabled for this
reason. However, modules that modify packet contents (like pf) may
end up completing a checksum on a TSO frame, leading to the NIC emitting
TSO segments with bad checksums.
To workaround this, restore the partial checksum in the mxge driver
when we're fed a TSO frame with a full checksum.
Reported by: Bob Healey
MFC after: 3 days
packets which go through each USB host controllers. Its implementations
are almost based on BPF code and very similar with it except it's
little bit customized for USB packet only. The userland program
usbdump(8) would be committed soon.
Discussed with: hps, thompsa, yongari
insertion/stripping and it also supports TSO over VLAN. Implement
TSO over VLAN support for MCP55 controller.
While I'm here clean up SIOCSIFCAP ioctl handler. Since nfe(4)
sets ifp capabilities based on various hardware flags in device
attach, there is no need to check hardware flags again in
SIOCSIFCAP ioctl handler. Also fix a bug which toggled both TX and
RX checksum offloading even if user requested either TX or RX
checksum configuration change.
Tested by: Rob Farmer ( rfarmer <> predatorlabs dot net )
of the MAC driver in order to attach miibus(4) on the first pass instead of
falling through to also calling it on the device_t of miibus(4). The latter
code flow was intended to attach the PHY drivers the same way regardless of
whether it's the first or a repeated pass, modulo the bus_generic_attach()
call in miibus_attach() which shouldn't be there. However, it turned out
that these variants cause miibus(4) to be attached twice under certain
conditions when using MAC drivers as modules.
Submitted by: yongari
MFC after: 3 days
not provide any MAC configuration interface for resolved flow
control parameters. There is even no register that configures water
mark which will control generation of pause frames.
However enabling flow control surely enhanced performance a lot.
such that nfe(4) does not work with MSI-X. When MSI-X support was
introduced, I remember MCP55 controller worked without problems so
the issue could be either PCI bridge or BIOS issue. But I also
noticed snd_hda(4) disabled MSI on all MCP55 chipset so I'm still
not sure this is generic issue of MCP55 chipset. If this was PCI
bridge issue we would have added it to a system wide black-list
table but it's not clear to me at this moment whether it was caused
by either broken BIOS or silicon bug of MCP55 chipset.
To workaround the issue, maintain a MSI/MSI-X black-list table in
driver and lookup base board manufacturer and product name from the
table before attempting to use MSI-X. If driver find an matching
entry, nfe(4) will not use MSI/MSI-X and fall back on traditional
INTx mode. This approach should be the last resort since it relies
on smbios and if another instance of MSI/MSI-X breakage is reported
with different maker/product, we may have to get the PCI bridge
black-listed instead of adding an new entry.
PR: kern/152150
K3765 datacard. After ejecting this device, it reappears using
the normal K3765 ID. It does not switch automatically
Reviewed by: n_hibma
Obtained from: OpenBSD
MFC after: 2 weeks
of certain MAC models from brgphy(4) to bge(4) where it belongs. While at it,
update the list of models having that restriction to what OpenBSD uses, which
in turn seems to have obtained that information from the Linux tg3 driver.
annex 31B full duplex flow control as well as the IFM_1000_T master
support committed in r215297. For atphy(4) and jmphy(4) this includes
changing these PHY drivers to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set).
- Rename {atphy,jmphy}_auto() to {atphy,jmphy}_setmedia() as these handle
other media types as well.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
case to previous panic behavior.
I have a real fix that changes the sg dma tag allocation
to be limited to the under 4GB address space but would
prefer to have review before committing.
Bug fixes:
* Fixed "inquiry data fails comparion at DV1 step"
* Fixed bad range input in bus_alloc_resource for ADAPTER_TYPE_B
* Fixed arcmsr driver prevent arcsas support for Areca SAS HBA ARC13x0
Many thanks to Areca for continuing to support FreeBSD.
This commit is intended for MFC before 8.2-RELEASE.
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
The external gpio pins are connected to a PLD on the i2c bus, unfortunatley
this device does not conform by failing to send an ack after each byte written.
The iicbb driver will abort the transfer when the address is not ack'd and it
would introduce a lot of churn to be able to pass a flag down to
iicbb_start/iicbb_write. Instead we do bad things by grabbing the iicbus but
then doing our own bit banging.
controller does not perform automatic switching from 1000Mbps link
to 10/100Mbps link when WOL is activated. Implement establishing
10/100Mps link with auto-negotiation in driver. Link status change
handler was modified to remove taskqueue based approach since driver
now needs synchronous handling for link establishment.
Submitted by: Yamagi Burmeister (lists <> yamagi.org ) (initial version)
Tested by: Yamagi Burmeister (lists <> yamagi.org )
MFC after: 1 week
and updated comments in the usb_quirk.h header file.
The main purpose of this is to expose the quirks for ejecting 3G
modules. usb_modeswitch in Linux does a great job of collecting
information on these, and with the quirks module people can try out the
modeswitch config file entries on FreeBSD, hence the SCSI strings in the
man page.
MFC after: 2 weeks
does-not-exist error when no client interface module is installed instead
of dereferencing NULL pointers. This eases implementation of platforms
that may or may not have Open Firmware.
It seems RTL8169/RTL8168/RTL810xE has a kind of interrupt
moderation mechanism but it is not documented at all. The magic
value dramatically reduced number of interrupts without noticeable
performance drops so apply it to all RTL8169/RTL8169 controllers.
Vendor's FreeBSD driver also applies it to RTL810xE controllers but
their Linux driver explicitly cleared the register, so do not
enable interrupt moderation for RTL810xE controllers.
While I'm here sort 8169 specific registers.
Obtained from: RealTek FreeBSD driver
There were a couple of attempts in the past to reduce it since it
took more than 1ms. Because mii_tick() periodically polls link
status, waiting more than 1ms for each GMII register access was
overkill. Unfortunately all previous attempts were failed with
various ways on different controllers.
This time, add additional 20us dealy at the end of GMII register
access which seems to requirement of all RealTek controllers to
issue next GMII register access request. This is the same way what
Linux does.
controllers. sk(4) never reprogrammed station address for Yukon
controllers so overriding station address with ifconfig(8) was not
possible.
Fix the bug by reprogramming all registers that control station
address, flow-control and virtual station address. Virtual station
address has no use at this moment since driver does not make use of
fail over feature.
Tested by: "Mikhail T." <mi+thun <> aldan.algebra.com>
MFC after: 1 week
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
based devices (QUALCOMMINC 0x2000). He made it use SCSI eject instead of
ZTE STOR eject. This prevented my ZTE MF626 dongle from switching.
- Apply both eject methods for ZTE STOR based devices. Works on my as
well as mav's device.
- Remove the duplicate.
- Sort the usbdevs entries for Qualcomm so this won't happen again.
- Add bootverbose message displaying the fact that we are ejecting (and
how).
Reviewed by: mav
MFC after: 2 weeks
copied as a template for _SRS, a string pointer for descriptor name is also
copied and it becomes stale as soon as it gets de-allocated[2]. Now _CRS is
used as a template for _SRS as ACPI specification suggests if it is usable.
The template from _PRS is still utilized but only when _CRS is not available
or broken. To avoid use-after-free the problem in this case, however, only
mandatory fields are copied, optional data is removed, and structure length
is adjusted accordingly.
Reported by: hps[1]
Analyzed by: avg[2]
Tested by: hps
useful counters like rl_missed_pkts is 16 bits quantity which is
too small to hold meaningful information happened in a second. This
means driver should frequently read these counters in order not to
lose accuracy and that approach is too inefficient in driver's
view. Moreover it seems there is no way to trigger an interrupt to
detect counter near-full or wraparound event as well as lacking
clearing the MAC counters. Another limitation of reading the
counters from RealTek controllers is lack of interrupt firing at
the end of DMA cycle of MAC counter read request such that driver
have to poll the end of the DMA which is a time consuming process
as well as inefficient. The more severe issue of the MAC counter
read request is it takes too long to complete the DMA. All these
limitation made maintaining MAC counters in driver impractical. For
now, just provide simple sysctl interface to trigger reading the
MAC counters. These counters could be used to track down driver
issues. Users can read MAC counters maintained in controller with
the following command.
#sysctl dev.re.0.stats=1
While I'm here add check for validity of dma map and allocated
memory before unloading/freeing them.
Tested by: rmacklem
information through devd. My E220 now produces the notification (1 line):
+u3g0 at bus=1 hubaddr=1 port=0 devaddr=2 interface=0 \
vendor=0x12d1 product=0x1003 devclass=0x00 devsubclass=0x00 \
sernum="" release=0x0000 intclass=0xff intsubclass=0xff \
ttyname=U0 ttyports=2 on uhub0
Note: serial/ufoma and net/uhso still provide port number and tty name
(uhso only) information through sysctls, which should now be removed.
Reviewed by: hpselasky
- Fix the loop count on detach (causing a panic on detaching a serial
dongle).
- Increase a buffer in case some driver want extra long tty device names
(postfixing the purpose of the tty for example, e.g. u3g.ppp).
notification. devd would stop evaluating at 'at' (not '<k>=<v>') and
hence prevent 'port=X' (and 'bus=<"on" string>) from making it into the
environment for the devd action.
Reviewed by: hselasky
MFC after: 2 weeks
- hw.usb.ucom.cons_unit is now split into
hw.usb.ucom.cons_unit/...cons_subunit.
Note: The tunable/sysctl hw.usb.ucom.cons_unit needs to be reviewed if
a) a console was defined a USB serial devices, and a USB device with
more than 1 subunit is present, and this device is attached before the
device functioning as a console
or
b) a console was defined on a USB device with more than 1 subunit
Reviewed by: hps
MFC after: 2 weeks
about but otherwise ignored. When allowing the master to be set manually via
ifconfig(8) by adding the former to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS
(as it should be) it seems to be unfavorable that a machine can be made to
panic with a simple ifconfig(8) invocation.
not able to trigger the issue with sample boards, some users seems
to suffer from freeze/lockup when system is booted without UTP cable
plugged in. I'm not sure whether this is BIOS issue or controller
bug. This change fixes AR8132 lockup issue seen on EEE PC.
Reported by: kmoore
Tested by: kmoore
In xbb_detach() only perform cleanup of our taskqueue and
device statistics structures if they have been initialized.
This avoids a panic when xbb_detach() is called on a partially
initialized device instance, due to an early failure in
attach.
Sponsored by: Spectra Logic Corporation
ip and tcp pointers were not reset after some
pullups. In practice this led to an NFS mount
failure when using UDP reported by Kevin Lo,
thanks Kevin. Fix from yongari, thank you!
the dual port BCM5717 and BCM5718 devices which are intended for
mainstream workstation and entry-level server designs and
represents the twelfth generation of NetXtreme Ethernet controllers.
This family is the successor to the BCM5714/BCM5715 family and
supports IPv4/IPv6 checksum offloading, TSO, VLAN hardware tagging,
jumbo frames, MSI/MSIX, IOV, RSS and TSS.
This change set supports all hardware features except IOV and
RSS/TSS. Unlike its predecessors, only extended RX buffer
descriptors can be posted to the jumbo producer ring. Single RX
buffer descriptors for jumbo frame are not supported. RSS requires
a more substantial set of changes and will apply to a larger set
of NetXtreme devices so RSS/TSS multi-queue support will be
implemented in a future releases.
Special thanks to Broadcom who kindly sent a sample board to me
and to davidch who gave provided the initial support code.
Submitted by: davidch (initial version)
HW donated by: Broadcom
'hw.acpi.remove_interface'. hw.acpi.install_interface lets you install new
interfaces. Conversely, hw.acpi.remove_interface lets you remove OS
interfaces from the pre-defined list in ACPICA. For example,
hw.acpi.install_interface="FreeBSD"
lets _OSI("FreeBSD") method to return 0xffffffff (or success) and
hw.acpi.remove_interface="Windows 2009"
lets _OSI("Windows 2009") method to return zero (or failure). Both are
comma-separated lists and leading white spaces are ignored. For example,
the following examples are valid:
hw.acpi.install_interface="Linux, FreeBSD"
hw.acpi.remove_interface="Windows 2006, Windows 2006.1"
- Chasin down bogus watchdogs has led to an improved
design to this handling, the hang decision takes
place in the tx cleanup, with only a simple report
check in local_timer. Our tests have shown no false
watchdogs with this code.
- VLAN fixes from jhb, the shadow vfta should be per
interface, but as global it was not. Thanks John.
- Bug fixes in the support for new PCH2 hardware.
- Thanks for all the help and feedback on the driver,
changes to lem with be coming shortly as well.
within the first 4 bytes of the EHCI memory space. For controllers that
use big-endian MMIO, reading them with 1- and 2-byte reads would then
return the wrong values. Instead, read the combined register with a 4-byte
read and mask out the interesting quantities.
VLAN hardware tagging to make TSO work over VLAN. So if VLAN
hardware tagging is disabled explicitly clear TSO over VLAN. While
I'm here allow disabling VLAN TX checksum offloading.
Tested by: Liudas < liudasb <> centras dot lt >
MFC after: 10 days
converted to use the mii_phy_add_media()/mii_phy_setmedia() pair instead
of mii_add_media()/mii_anar() remove the latter.
- Declare mii_media mii_media_table static as it shouldn't be used outside
of mii_physubr.c.
MFC after: never
interface also has such connectors.
- In tl_attach() unify three different ways of obtaining the device and
vendor IDs and remove the now obsolete tl_dinfo from tl_softc.
- Given that tlphy(4) only handles the integrated PHYs of NICs driven by
tl(4) make it only probe on the latter.
- Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia().
- Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4)
by ignoring the native one by just comparing the device_t's directly rather
than the device name.
- Use mii_phy_add_media() instead of mii_add_media(). I'm not sure how
this driver actually managed to work before as mii_add_media() is
intended to be used to gether with mii_anar() while mii_phy_add_media()
is intended to be used with mii_phy_setmedia(), however this driver
mii_add_media() along with mii_phy_setmedia().
to BCM6906 A0/A2. This should fix a long standing BCM5906 A2 lockup
issues. Data sheet explicitly mentions BCM5906 A0, A1 and A2 use
de-pipelined mode on these revisions.
Special thanks to Buganini who tried all combinations of
experimental patches for more than 10 days.
Tested by: Buganini <buganini <> gmail dot com >
the association notification), the included information though always
contains an elem block with an odd number of bytes. We handle the last
byte as if it might contain a whole elem block, this of course is not
true as one byte is not enough to hold a block, we therefore discard the
complete frame. The solution here is to subtract one from the actual
notification length, this is also what the Linux driver does. With this
change the frames ends exactly where the last elem block ends.
This commit also reverts r214160 which is no longer required and now even
wrong.
MFC after: 1 week
auto-negotiation results in half-duplex operation, excess collision
on the ethernet link may cause internal chip delays that may result
in subsequent valid frames being dropped due to insufficient
receive buffer resources. The workaround is to choose de-pipeline
method as a flow control decision for SDI. De-pipeline method
allows only 1 data in TxMbuf at a time such that a request to RDMA
from SDI is made only when TxMbuf is empty. Thanks for david for
providing detailed errata information.
PCI-express or PCI-X capabilities if we are running in a virtual machine.
- Whitelist the Intel 82440 chipset used by QEMU.
Tested by: jfv
MFC after: 1 week
break the loop instead. We want to run the code after the while loop
to set an associd and capinfo. If we don't do this net80211 will drop
frames because it assumes the node has not yet been associated.
MFC after: 1 week
ignore BARs that are invalid due to having a size of zero, not to ignore
BARs with an existing base of zero. While here, reorganize the code
slightly to make the intent clearer.
Reported by: avg
MFC after: 1 week
Specification Rev. 1.2. Rename pp_pcmcsr field of PM capabilities to pp_bse
to avoid further confusions and adjust some comments accordingly. The real
PMCSR (Power Management Control/Status Register) is PCIR_POWER_STATUS and
it is actually BSE (PCI-to-PCI Bridge Support Extensions) register.
of proper value. It caused bunch of "EMPTY CRPB" messages and potentially
may cause premature requests completion, which could cause data corruption.
For most cases it seems enough to just reread register to get proper value.
To protect against worse cases - erase processed queue entries with
impossible values and ignore them if problem still happen.
released a drver lock for shared interrupt case such that it caused
panic. While I'm here check whether driver is still running before
serving TX/RX handler.
Reported by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
Tested by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
MFC after: 3 days
receive two back-to-back send BDs with less than or equal to 8
total bytes then the device may hang. The two back-to-back send
BDs must be in the same frame for this failure to occur.
Thanks to davidch for detailed errata information.
Reviewed by: davidch
o Add support for backend devices (e.g. blkback)
o Implement extensions to the Xen para-virtualized block API to allow
for larger and more outstanding I/Os.
o Import a completely rewritten block back driver with support for fronting
I/O to both raw devices and files.
o General cleanup and documentation of the XenBus and XenStore support code.
o Robustness and performance updates for the block front driver.
o Fixes to the netfront driver.
Sponsored by: Spectra Logic Corporation
sys/xen/xenbus/init.txt:
Deleted: This file explains the Linux method for XenBus device
enumeration and thus does not apply to FreeBSD's NewBus approach.
sys/xen/xenbus/xenbus_probe_backend.c:
Deleted: Linux version of backend XenBus service routines. It
was never ported to FreeBSD. See xenbusb.c, xenbusb_if.m,
xenbusb_front.c xenbusb_back.c for details of FreeBSD's XenBus
support.
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenbus/xenbus_xs.c:
sys/xen/xenbus/xenbus_comms.c:
sys/xen/xenbus/xenbus_comms.h:
sys/xen/xenstore/xenstorevar.h:
sys/xen/xenstore/xenstore.c:
Split XenStore into its own tree. XenBus is a software layer built
on top of XenStore. The old arrangement and the naming of some
structures and functions blurred these lines making it difficult to
discern what services are provided by which layer and at what times
these services are available (e.g. during system startup and shutdown).
sys/xen/xenbus/xenbus_client.c:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_probe.c:
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
Split up XenBus code into methods available for use by client
drivers (xenbus.c) and code used by the XenBus "bus code" to
enumerate, attach, detach, and service bus drivers.
sys/xen/reboot.c:
sys/dev/xen/control/control.c:
Add a XenBus front driver for handling shutdown, reboot, suspend, and
resume events published in the XenStore. Move all PV suspend/reboot
support from reboot.c into this driver.
sys/xen/blkif.h:
New file from Xen vendor with macros and structures used by
a block back driver to service requests from a VM running a
different ABI (e.g. amd64 back with i386 front).
sys/conf/files:
Adjust kernel build spec for new XenBus/XenStore layout and added
Xen functionality.
sys/dev/xen/balloon/balloon.c:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/blkfront/blkfront.c:
sys/xen/xenbus/...
sys/xen/xenstore/...
o Rename XenStore APIs and structures from xenbus_* to xs_*.
o Adjust to use of M_XENBUS and M_XENSTORE malloc types for allocation
of objects returned by these APIs.
o Adjust for changes in the bus interface for Xen drivers.
sys/xen/xenbus/...
sys/xen/xenstore/...
Add Doxygen comments for these interfaces and the code that
implements them.
sys/dev/xen/blkback/blkback.c:
o Rewrite the Block Back driver to attach properly via newbus,
operate correctly in both PV and HVM mode regardless of domain
(e.g. can be in a DOM other than 0), and to deal with the latest
metadata available in XenStore for block devices.
o Allow users to specify a file as a backend to blkback, in addition
to character devices. Use the namei lookup of the backend path
to automatically configure, based on file type, the appropriate
backend method.
The current implementation is limited to a single outstanding I/O
at a time to file backed storage.
sys/dev/xen/blkback/blkback.c:
sys/xen/interface/io/blkif.h:
sys/xen/blkif.h:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
Extend the Xen blkif API: Negotiable request size and number of
requests.
This change extends the information recorded in the XenStore
allowing block front/back devices to negotiate for optimal I/O
parameters. This has been achieved without sacrificing backward
compatibility with drivers that are unaware of these protocol
enhancements. The extensions center around the connection protocol
which now includes these additions:
o The back-end device publishes its maximum supported values for,
request I/O size, the number of page segments that can be
associated with a request, the maximum number of requests that
can be concurrently active, and the maximum number of pages that
can be in the shared request ring. These values are published
before the back-end enters the XenbusStateInitWait state.
o The front-end waits for the back-end to enter either the InitWait
or Initialize state. At this point, the front end limits it's
own capabilities to the lesser of the values it finds published
by the backend, it's own maximums, or, should any back-end data
be missing in the store, the values supported by the original
protocol. It then initializes it's internal data structures
including allocation of the shared ring, publishes its maximum
capabilities to the XenStore and transitions to the Initialized
state.
o The back-end waits for the front-end to enter the Initalized
state. At this point, the back end limits it's own capabilities
to the lesser of the values it finds published by the frontend,
it's own maximums, or, should any front-end data be missing in
the store, the values supported by the original protocol. It
then initializes it's internal data structures, attaches to the
shared ring and transitions to the Connected state.
o The front-end waits for the back-end to enter the Connnected
state, transitions itself to the connected state, and can
commence I/O.
Although an updated front-end driver must be aware of the back-end's
InitWait state, the back-end has been coded such that it can
tolerate a front-end that skips this step and transitions directly
to the Initialized state without waiting for the back-end.
sys/xen/interface/io/blkif.h:
o Increase BLKIF_MAX_SEGMENTS_PER_REQUEST to 255. This is
the maximum number possible without changing the blkif
request header structure (nr_segs is a uint8_t).
o Add two new constants:
BLKIF_MAX_SEGMENTS_PER_HEADER_BLOCK, and
BLKIF_MAX_SEGMENTS_PER_SEGMENT_BLOCK. These respectively
indicate the number of segments that can fit in the first
ring-buffer entry of a request, and for each subsequent
(sg element only) ring-buffer entry associated with the
"header" ring-buffer entry of the request.
o Add the blkif_request_segment_t typedef for segment
elements.
o Add the BLKRING_GET_SG_REQUEST() macro which wraps the
RING_GET_REQUEST() macro and returns a properly cast
pointer to an array of blkif_request_segment_ts.
o Add the BLKIF_SEGS_TO_BLOCKS() macro which calculates the
number of ring entries that will be consumed by a blkif
request with the given number of segments.
sys/xen/blkif.h:
o Update for changes in interface/io/blkif.h macros.
o Update the BLKIF_MAX_RING_REQUESTS() macro to take the
ring size as an argument to allow this calculation on
multi-page rings.
o Add a companion macro to BLKIF_MAX_RING_REQUESTS(),
BLKIF_RING_PAGES(). This macro determines the number of
ring pages required in order to support a ring with the
supplied number of request blocks.
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
o Negotiate with the other-end with the following limits:
Reqeust Size: MAXPHYS
Max Segments: (MAXPHYS/PAGE_SIZE) + 1
Max Requests: 256
Max Ring Pages: Sufficient to support Max Requests with
Max Segments.
o Dynamically allocate request pools and segemnts-per-request.
o Update ring allocation/attachment code to support a
multi-page shared ring.
o Update routines that access the shared ring to handle
multi-block requests.
sys/dev/xen/blkfront/blkfront.c:
o Track blkfront allocations in a blkfront driver specific
malloc pool.
o Strip out XenStore transaction retry logic in the
connection code. Transactions only need to be used when
the update to multiple XenStore nodes must be atomic.
That is not the case here.
o Fully disable blkif_resume() until it can be fixed
properly (it didn't work before this change).
o Destroy bus-dma objects during device instance tear-down.
o Properly handle backend devices with powef-of-2 sector
sizes larger than 512b.
sys/dev/xen/blkback/blkback.c:
Advertise support for and implement the BLKIF_OP_WRITE_BARRIER
and BLKIF_OP_FLUSH_DISKCACHE blkif opcodes using BIO_FLUSH and
the BIO_ORDERED attribute of bios.
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
Fix various bugs in blkfront.
o gnttab_alloc_grant_references() returns 0 for success and
non-zero for failure. The check for < 0 is a leftover
Linuxism.
o When we negotiate with blkback and have to reduce some of our
capabilities, print out the original and reduced capability before
changing the local capability. So the user now gets the correct
information.
o Fix blkif_restart_queue_callback() formatting. Make sure we hold
the mutex in that function before calling xb_startio().
o Fix a couple of KASSERT()s.
o Fix a check in the xb_remove_* macro to be a little more specific.
sys/xen/gnttab.h:
sys/xen/gnttab.c:
Define GNTTAB_LIST_END publicly as GRANT_REF_INVALID.
sys/dev/xen/netfront/netfront.c:
Use GRANT_REF_INVALID instead of driver private definitions of the
same constant.
sys/xen/gnttab.h:
sys/xen/gnttab.c:
Add the gnttab_end_foreign_access_references() API.
This API allows a client to batch the release of an array of grant
references, instead of coding a private for loop. The implementation
takes advantage of this batching to reduce lock overhead to one
acquisition and release per-batch instead of per-freed grant reference.
While here, reduce the duration the gnttab_list_lock is held during
gnttab_free_grant_references() operations. The search to find the
tail of the incoming free list does not rely on global state and so
can be performed without holding the lock.
sys/dev/xen/xenpci/evtchn.c:
sys/dev/xen/evtchn/evtchn.c:
sys/xen/xen_intr.h:
o Implement the bind_interdomain_evtchn_to_irqhandler API for HVM mode.
This allows an HVM domain to serve back end devices to other domains.
This API is already implemented for PV mode.
o Synchronize the API between HVM and PV.
sys/dev/xen/xenpci/xenpci.c:
o Scan the full region of CPUID space in which the Xen VMM interface
may be implemented. On systems using SuSE as a Dom0 where the
Viridian API is also exported, the VMM interface is above the region
we used to search.
o Pass through bus_alloc_resource() calls so that XenBus drivers
attaching on an HVM system can allocate unused physical address
space from the nexus. The block back driver makes use of this
facility.
sys/i386/xen/xen_machdep.c:
Use the correct type for accessing the statically mapped xenstore
metadata.
sys/xen/interface/hvm/params.h:
sys/xen/xenstore/xenstore.c:
Move hvm_get_parameter() to the correct global header file instead
of as a private method to the XenStore.
sys/xen/interface/io/protocols.h:
Sync with vendor.
sys/xeninterface/io/ring.h:
Add macro for calculating the number of ring pages needed for an N
deep ring.
To avoid duplication within the macros, create and use the new
__RING_HEADER_SIZE() macro. This macro calculates the size of the
ring book keeping struct (producer/consumer indexes, etc.) that
resides at the head of the ring.
Add the __RING_PAGES() macro which calculates the number of shared
ring pages required to support a ring with the given number of
requests.
These APIs are used to support the multi-page ring version of the
Xen block API.
sys/xeninterface/io/xenbus.h:
Add Comments.
sys/xen/xenbus/...
o Refactor the FreeBSD XenBus support code to allow for both front and
backend device attachments.
o Make use of new config_intr_hook capabilities to allow front and back
devices to be probed/attached in parallel.
o Fix bugs in probe/attach state machine that could cause the system to
hang when confronted with a failure either in the local domain or in
a remote domain to which one of our driver instances is attaching.
o Publish all required state to the XenStore on device detach and
failure. The majority of the missing functionality was for serving
as a back end since the typical "hot-plug" scripts in Dom0 don't
handle the case of cleaning up for a "service domain" that is not
itself.
o Add dynamic sysctl nodes exposing the generic ivars of
XenBus devices.
o Add doxygen style comments to the majority of the code.
o Cleanup types, formatting, etc.
sys/xen/xenbus/xenbusb.c:
Common code used by both front and back XenBus busses.
sys/xen/xenbus/xenbusb_if.m:
Method definitions for a XenBus bus.
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusb_back.c:
XenBus bus specialization for front and back devices.
MFC after: 1 month
added with hw.pci.do_powerstate but the PCI version was splitted into two
separate tunables later and now this is completely stale. To make it worse,
PCI devices enumerated in ACPI tree ignore this tunable as it is handled by
a function in acpi_pci.c instead.
knowledges from the file. All PCI devices enumerated in ACPI tree must use
correct one from acpi_pci.c any way. Reduce duplicate codes as we did for
pci.c in r213905. Do not return ESRCH from PCIB_POWER_FOR_SLEEP method.
When the method is not found, just return zero without modifying the given
default value as it is completely optional. As a side effect, the return
state must not be NULL. Note there is actually no functional change by
removing ESRCH because acpi_pcib_power_for_sleep() always returns zero.
Adjust debugging messages and add new ones under bootverbose to help
debugging device power state related issues.
Reviewed by: jhb, imp (earlier versions)
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
To protect against malicious software, we demand that the file name is at
a particular location (i.e. appended to the mdio structure) for it to be
treated as in-kernel.
important for USB 2.0 devices and some of them reported to have problems
with large transactions. But USB 3.0 benchmarks show that limited number
of transactions per second on USB makes impossible to reach high transfer
speeds without using bigger transactions.
On my tests this change allows to read up to 220MB/s from USB-attached SSD
(at block size of 256-512KB), comparing to only 113MB/s without it.
Reviewed by: hselasky
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
This file was missed in r213893.
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
- fix the leak of command struct on error
- simplify the cleanup logic
- EINPROGRESS is not a fatal error
- buggy comment and error message
Reviewed by: ken
replace mii_phy_probe() altogether. Compared to the latter the advantages
of mii_attach() are:
- intended to be called multiple times in order to attach PHYs in multiple
passes (f.e. in order to only use sub-ranges of the 0 to MII_NPHY - 1
range)
- being able to pass along the capability mask from the NIC to the PHY
drivers
- being able to specify at which address (phyloc) to probe for a PHY
(instead of always probing at all addresses from 0 to MII_NPHY - 1)
- being able to specify which PHY instance (offloc) to attach
- being able to pass along MIIF_* flags from the NIC to the PHY drivers
(f.e. as required to indicated to the PHY drivers that flow control is
supported by the NIC driver, which actually is the motivation for this
change).
While at it, I used the opportunity to get rid of some hacks in mii(4)
like miibus_probe() generally doing work besides sheer probing and the
"EVIL HACK" (which will vanish entirely along with mii_phy_probe()) by
passing the struct ifnet pointer via an argument of mii_attach() as well
as to fix some resource leaks in mii(4) in case something fails.
Commits which will update the PHY drivers to honor the MII flags passed
down from the NIC drivers and take advantage of mii_attach() to get rid
of certain types of hacks in NIC and PHY drivers as well as a conversion
of the remaining uses of mii_phy_probe() will follow shortly.
Reviewed by: jhb, yongari
Obtained from: NetBSD (partially)
proper solution which is to not use the TERMINATE pointer, but rather
link to a halted TD. The initial fix was due to a misunderstanding
about how the EHCI hardware works. Thanks to Alan Stern for clearing
this up. This patch can increase mass storage read performance
significantly when the IRQ rate is less than 8000 IRQ/s.
Approved by: thompsa (mentor)
header parser uses m_pullup(9) to get access to mbuf chain.
m_pullup(9) can allocate new mbuf chain and free old one if the
space left in the mbuf chain is not enough to hold requested
contiguous bytes. Previously drivers can use stale ip/tcp header
pointer if m_pullup(9) returned new mbuf chain.
Reported by: Andrew Boyer (aboyer <> averesystems dot com)
MFC after: 10 days
port such that reading station address from second port always
returned 0xFF:0xFF:0xFF:0xFF:0xFF:0xFF Unfortunately it seems there
is no easy way to know whether SROM is shared or not. Workaround
the issue by traversing dc(4) device list and see whether we're
using second port and use station address of controller 0 as base
station address of second port.
PR: kern/79262
MFC after: 2 weeks
auto polling such that it made all controllers obtain link status
information from the state of the LNKRDY input signal. Broadcom
recommends disabling auto polling such that driver should rely on
PHY interrupts for link status change indications. Unfortunately it
seems some controllers(BCM5703, BCM5704 and BCM5705) have PHY
related issues so Linux took other approach to workaround it.
bge(4) didn't follow that and it used to enable auto polling to
workaround it. Restore this old behavior for BCM5700 family
controllers and BCM5705 to use auto polling. For BCM5700 and
BCM5701, it seems it does not need to enable auto polling but I
restored it for safety.
Special thanks to marius who tried lots of patches with patience.
Reported by: marius
Tested by: marius
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add development feature about limiting the
maximum datagram count in each NCM payload.
- zero-pad alignment data
- add TX-interval tuning sysctl
Approved by: thompsa (mentor)
Link UP state could be reported first before actual completion of
auto-negotiation. This change makes bge(4) reprogram BGE_MAC_MODE,
BGE_TX_MODE and BGE_RX_MODE register only after controller got a
valid link.
receive producer ring only for BCM5700. It was believed that
BCM5700 with external SSRAM is the only controller that supports
mini ring but it seems all BCM570[0-4] requires to disable mini
receive producer ring. Otherwise, it caused unexpected RX DMA
error or watchdog timeouts.
Reported by: marius, Steve Kargl <sgk <> troutmask dot apl dot washington dot edu>
Tested by: marius, Steve Kargl <sgk <> troutmask dot apl dot washington dot edu>
Short description of the changes:
- attempt to retry some commands for which it is possible (read, query)
- always make a short sleep before checking EC status in polled mode
- periodically poll EC status in interrupt mode
- change logic for detecting broken interrupt delivery and falling back
to polled mode
- check that EC is ready for input before starting a new command, wait
if necessary
This commit is based on the original patch by David Naylor.
PR: kern/150517
Submitted by: David Naylor <naylor.b.david@gmail.com>
Reviewed by: jkim
MFC after: 3 weeks
before setting the flag, interrupt was already enabled such that
interrupt handler could be run before setting IFF_DRV_RUNNING flag.
This can lose initial link state change interrupt which in turn
make bge(4) think that it still does not have valid link. Fix this
race by protecting the taskqueue with a driver lock.
While I'm here move reenabling interrupt code after handling of link
state chage.
Reviewed by: davidch
Previously bge(4) always enabled auto polling for non-BGE_FLAG_TBI
controllers. With this change, auto polling is not used anymore so
polling through mii(4) was introduced.
Reviewed by: davidch
It seems axe(4) controllers support interrupt endpoint such that
enabling interrupt endpoint generates about 1000 interrupts/sec.
Controllers transfer 8 bytes data through interrupt endpoint and
the data include link UP/DOWN state as well as some PHY related
information. Previously axe(4) didn't use the transferred data and
didn't even try to read the data. Because axe(4) counts on mii(4)
to detect link state changes there is no need to use interrupt
endpoint here.
This change fixes generation of unnecessary interrupts which was
seen when interface is brought to UP.
No objections from: hselasky
opposition to the change, since really we need to implement missing
functionality in drivers or the 802.3 layer.
For now, restore a reminder message for a missing rum_update_mcast, but
print it only once.
controller, but make it optional.
After a problem report from Andrew Boyer, it looks like the LSI
chip may have issues (the watchdog timer fired) if too many aborts
are sent down to the chip at the same time. We know that task
management commands are serialized, and although the manual doesn't
say it, it may be a good idea to just send one at a time.
But, since I'm not certain that this is necessary, add a tunable
and sysctl variable (hw.mps.%d.allow_multiple_tm_cmds) to control
the driver's behavior.
mps.c: Add support for the sysctl and tunable, and add a
comment about the possible return values to
mps_map_command().
mps_sas.c: Run all task management commands through two new
routines, mpssas_issue_tm_request() and
mpssas_complete_tm_request().
This allows us to optionally serialize task
management commands. Also, change things so that
the response to a task management command always
comes back through the callback. (Before it could
come via the callback or the return value.)
mpsvar.h: Add softc variables for the list of active task
management commands, the number of active commands,
and whether we should allow multiple active task
management commands. Add an active command flag.
mps.4: Describe the new sysctl/loader tunable variable.
Sponsored by: Spectra Logic Corporation
as 5788. This caused BGE_MISC_LOCAL_CTL register is used to
generate link state change interrupt for non-5788 controllers. The
interrupt handler may or may not detect link state attention as
status block wouldn't be updated when an interrupt was generated
with BGE_MISC_LOCAL_CTL register. All controllers except 5700 and
5788 should use host coalescing mode register to trigger an
interrupt.
versions of controller support different number of ring control
blocks such that adjust code a bit to access known number of
send/receive ring control blocks. Previously bge(4) blindly
accessed 16 send/receive RCBs. Also move initializing standard
receive producer ring producer index, jumbo receive producer ring
producer index and mini receive producer ring producer index to
the end of each receive producer ring initialization.
Do not assume mini receive producer ring is available only when
controller has jumbo frame capability, instead explicitly check
ASIC version BCM5700 to disable mini receive producer ring.
Additionally always enable send ring 0 regardless of controller
versions. Previously bge(4) didn't enable send ring 0 if controller
is BGE_IS_5705_PLUS. Becase bge(4) need 1 send ring to send frames
at least, I have no idea how it would have worked so far.
Submitted by: davidch
dev.bce.<unit>.nvram_dump
Add the capability to write the complete contents of the NVRAM via sysctl
dev.bce.<unit>.nvram_write
These are only available if the kernel option BCE_DEBUG is enabled.
The nvram_write sysctl also requires the kernel option
BCE_NVRAM_WRITE_SUPPORT to be enabled. These are to be used at your
own caution. Since the MAC addresses are stored in the NVRAM, if you
dump one NIC and restore it on another NIC the destination NIC's
MAC addresses will not be preserved. A tool can be made using these
sysctl's to manage the on-chip firmware.
Reviewed by: davidch, yongari
BGE_MI_MODE register accesses. Previously bge(4) used to read
BGE_MI_MODE register to detect whether it needs to disable
autopolling feature or not. Because we don't touch autopolling in
other part of driver there is no reason to read BGE_MI_MODE
register given that we know default value in advance. In order to
achieve the goal, check whether the controller has CPMU(Central
Power Mangement Unit) capability. If controller has CPMU feature,
use 500KHz MII management interface(mdio/mdc) frequency regardless
core clock frequency. Otherwise use default MII clock. While I'm
here, add CPMU register definition.
In bge_miibus_readreg(), rearrange code a bit and remove goto
statement. In bge_miibus_writereg(), make sure to restore
autopolling even if MII write failed. The delay time inserted after
accessing BGE_MI_MODE register increased from 40us to 80us.
The default PHY address is now stored in softc. All PHYs supported
by bge(4) currently uses PHY address 1 but it will be changed when
we add newer controllers. This change will make it easier to change
default PHY address depending on PHY models.
Submitted by: davidch
special eject command to reappear as modem. It also requires DIR_IN flag
in the command message, so we supply some dummy data along with the command.
Feedback from X080S owners appreciated. I have not a pure Alcatel/TCTMobile
device, but another one under "Svyaznoy" (Связной) brand, and I didn't yet
managed to get it working. It is successfully recognized, it responds to
AT commands, but it shuts up right after successfull CONNECT response.
Reviewed by: hps
successfully received a frame but we failed to pass it to upper
stack due to lack of resources. So update if_iqdrops counter
instead of updating if_ierrors counter.
mode in the USB core. The patch mostly consists of updating the USB
HUB code to support USB 3.0 HUBs. This patch also add some more USB
controller methods to support more active-alike USB controllers like
the XHCI which needs to be informed about various device state events.
USB 3.0 HUBs are not tested yet, due to lack of hardware, but are
believed to work.
After this update the initial device descriptor is only read twice
when we know that the bMaxPacketSize is too small for a single packet
transfer of this descriptor.
Approved by: thompsa (mentor)
controllers combine multiple TX requests into single one if there
is room in TX buffer of controller. Updating TX packet counter at
the end of TX completion resulted in incorrect TX packet counter as
axe(4) thought it sent 1 packet. There is no easy way to know how
many combined TX were completed in the callback.
Because this change updates TX packet counter before actual
transmission, it may not be ideal one. But I believe it's better
than showing fake 8kpps under high TX load. With this change, TX
shows 221kpps on Linksus USB200M.
these names are used in data sheet. Also use UnicastPkts,
MulticastPkts and BroadcastPkts instead of UcastPkts, McastPkts
and BcastPkts to clarify its meaning.
Suggested by: bde
scratch. This driver adds support for USB3.0 devices. The XHCI
interface is also backwards compatible to USB2.0 and USB1.0 and will
evntually replace the OHCI/UHCI and EHCI drivers.
There will be follow-up commits during the coming week to link the
driver into the default kernel build and add missing USB3.0
functionality in the USB core. Currently only the driver files are
committed.
Approved by: thompsa (mentor)
different PHY instance being selected and isolation out into the wrappers
around the service methods rather than duplicating them over and over
again (besides, a PHY driver shouldn't need to care about which instance
it actually is).
- Centralize the check for the need to isolate a non-zero PHY instance not
supporting isolation in mii_mediachg() and just ignore it rather than
panicing, which should sufficient given that a) things are likely to
just work anyway if one doesn't plug in more than one port at a time and
b) refusing to attach in this case just leaves us in a unknown but most
likely also not exactly correct configuration (besides several drivers
setting MIIF_NOISOLATE didn't care about these anyway, probably due to
setting this flag for no real reason).
- Minor fixes like removing unnecessary setting of sc->mii_anegticks,
using sc->mii_anegticks instead of hardcoded values etc.
number of unexplained interrupt problems. For some reason, using HPET
interrupts there breaks HDA sound. Legacy route mode interrupts reported
to work fine there.
controllers. bge(4) exported MAC statistics on controllers that
maintain the statistics in the NIC's internal memory. Newer
controllers require register access to fetch these values. These
counters provide useful information to diagnose driver issues.
parent driver. Use that information to configure flow-control.
One drawback is there is no way to disable flow-control as we still
don't have proper way to not advertise RX/TX pause capability to
link partner. But I don't think it would cause severe problems and
users can selectively disable flow-control in switch port.
- license clause now contains "AUTHOR AND CONTRIBUTORS"
instead of just "AUTHOR"
- Add license/copyright to gpioc.c
Spotted by: Edward Tomasz Napierala, Andrew Turner
which were raised during hot-swap events. Now such events trigger cam
rescans, as is done in the mps driver.
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
has reached. This reduced number of dropped frames when
flow-control is enabled. Previously it dropped incoming frames once
RX MBUF low watermark has reached. The value used in MAC RX MBUF
low watermark is greater than or equal to 4 so receiving two more
RX frames should not be a problem.
Obtained from: OpenBSD
- GPIO bus controller interface
- GPIO bus interface
- Implementation of GPIO led(4) compatible device
- Implementation of iic(4) bus over GPIO (author: Luiz Otavio O Souza)
Tested by: Luiz Otavio O Souza, Alexandr Rybalko
- Sync shared code with Intel internal
- New client chipset support added
- em driver - fixes to 82574, limit queues to 1 but use MSIX
- em driver - large changes in TX checksum offload and tso
code, thanks to yongari.
- some small changes for watchdog issues.
- igb driver - local timer watchdog code was missing locking
this and a couple other watchdog related fixes.
- bug in rx discard found by Andrew Boyer, check for null pointer
MFC: a week
too many bge(4) controllers there and model name does not
necessarily match asic/chip revision. Relying on VPD string made
it hard to identify exact asic/chip revision so the first step to
debug bge(4) was getting exact asic/chip information with verbose
boot which may not be available on production server.
address spaces
There has been no need to do that starting with ACPICA 20040427 as
AcpiEnableSubsystem() installs the handlers automatically.
Additionaly, explicitly calling AcpiInstallAddressSpaceHandler before
AcpiEnableSubsystem is not supported by ACPICA and leads to too early
execution of _REG methods in some DSDTs, which may result in problems.
Big thanks to Robert Moore of ACPICA/Intel for explaining the above.
Reported by: Daniel Bilik <daniel.bilik@neosystem.cz>
Tested by: Daniel Bilik <daniel.bilik@neosystem.cz>
Reviewed by: jkim
Suggested by: "Moore, Robert" <robert.moore@intel.com>
MFC after: 1 week
StarFire controller does not require controller reinitialization to
program perfect filters. While here, make driver immediately exit
from interrupt/polling handler if driver reinitialized controller.
PR: kern/87506
- Add a single sysctl procedure to all three drivers to read an arbitrary
register (the register is passed as arg2). Use it to replace existing
routines in igb(4) that used a separate routine for each register, and
to add support for missing stats in em(4) and lem(4).
- Move the 'rx_overruns' and 'watchdog_timeouts' stats out of the MAC stats
section as they are driver stats, not MAC counters.
- Simplify the code that creates per-queue stats in igb(4) to use a single
loop and remove duplicated code.
- Properly read all 64 bits of the 'good octets received/transmitted' in
em(4) and lem(4).
- Actually read the interrupt count registers in em(4), and drop the
'host to card' sysctl stats from em(4) as they are not implemented in
any of the hardware this driver supports.
- Restore several stats to em(4) that were lost in the earlier stats
conversion including per-queue stats.
- Export several MAC stats in em(4) that were exported in igb(4) but not
in em(4).
- Export stats in lem(4) using individual sysctls as in em(4) and igb(4).
Reviewed by: jfv
MFC after: 1 week
the device:
- unobscure some of the code by moving it into its own functions
- get rid of some magic numbers
- create similar structure as the reference driver has, this should
make further syncs easier
particular edge case where X-axis resolution is not multiple of font width.
Now we just advance enough scan lines, then deduct a partial scan line.
It is more intuitive than the previous code. Apply the same wisdom to EGA
and VGA planar renderers for consistency.
Reported by: David DEMELIER (demelier dot david at gmail dot com)
When the driver is completely saturated with commands (1024 in the
case of the SAS2008 in my test system), I/O stops. If we tell CAM
that we have one less command slot than we have actually allocated,
everything works fine. We also need a few extra command slots to
allow for aborts and other task management commands to be sent down.
This needs more investigation to determine the root cause, but for
now this fixes things in my testing.
mps.c: Change a printf() to mps_printf().
mps_sas.c: Subtract 5 command slots when we tell CAM how many
commands we can handle.
Add some commented-out logic to print the contents
the CDBs for timed-out commands. This can help
in debugging devices that are timing out. This
will be uncommented once I bring some CAM changes in.
Reported by: Andrew Boyer <aboyer at averesystems dot com>
According to the MPT2 spec, task management commands are
serialized, and so no I/O should start while task management
commands are active.
So, to comply with that, freeze the SIM queue before we send any
task management commands (abort, target reset, etc.) down to the
IOC. We unfreeze the queue once the task management command
completes.
It isn't clear from the spec whether multiple simultaneous task
management commands are supported. Right now it is possible to
have multiple outstanding task management commands, especially in
the abort case. Multiple outstanding aborts do complete
successfully, so it may be supported.
We also don't yet have any recovery mechanism (e.g. reset the IOC)
if the task management command fails.
already updated after allocating mbuf so driver had to use the last
index instead of using next producer index. This should fix driver
hang which may happen under high network load.
Reported by: Igor Sysoev <is <> rambler-co dot ru>, Vlad Galu <dudu <> dudu dot ro>
Tested by: Igor Sysoev <is <> rambler-co dot ru>, Vlad Galu <dudu <> dudu dot ro>
MFC after: 10 days
Add a drain function for struct sysctl_req, and use it for a variety
of handlers, some of which had to do awkward things to get a large
enough SBUF_FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing
NUL byte. This behaviour was preserved, though it should not be
necessary.
Reviewed by: phk (original patch)
- Don't probe for PHYs if we already know to use a SERDES. Unlike as with
cas(4) this only serves to speed up the the device attach though and can
only be determined via the OFW device tree but not from the VPD.
- Don't touch the MIF when using a SERDES.
- Add some missing bus space barriers, mainly in the PCS code path.
- D_TRACKCLOSE may be used there as d_close() are expected to match up
d_open() calls
- Replace the hand-crafted counter and flag with the
device_busy()/device_unbusy() proper usage.
Sponsored by: Sandvine Incorporated
Reported by: Mark Johnston <mjohnston at sandvine dot com>
Tested by: Mark Johnston
Reviewed by: emaste
MFC after: 10 days
when the original offset is bigger than size of one page. X86BIOS macros
cannot be used here because it is assumed address is only linear in a page.
Tested by: netchild
unexpected things in copyout(9) and so wiring the user buffer is not
sufficient to perform a copyout(9) while holding a random mutex.
Requested by: nwhitehorn
ACPI specification sates that if P_LVL2_LAT > 100, then a system doesn't
support C2; if P_LVL3_LAT > 1000, then C3 is not supported.
But there are no such rules for Cx state data returned by _CST. If a
state is not supported it should not be included into the return
package. In other words, any latency value returned by _CST is valid,
it's up to the OS and/or user to decide whether to use it.
Submitted by: nork
Suggested by: mav
MFC after: 1 week
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
Bring in a driver for the LSI Logic MPT2 6Gb SAS controllers.
This driver supports basic I/O, and works with SAS and SATA drives and
expanders.
Basic error recovery works (i.e. timeouts and aborts) as well.
Integrated RAID isn't supported yet, and there are some known bugs.
So this isn't ready for production use, but is certainly ready for
testing and additional development. For the moment, new commits to this
driver should go into the FreeBSD Perforce repository first
(//depot/projects/mps/...) and then get merged into -current once
they've been vetted.
This has only been added to the amd64 GENERIC, since that is the only
architecture I have tested this driver with.
Submitted by: scottl
Discussed with: imp, gibbs, will
Sponsored by: Yahoo, Spectra Logic Corporation
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
malo and mwl use the firmware framework to access firmware images.
Depending on the firmware modules itself is not required and in this
case even wrong because no modules with those names exist.
Pointed out by: brucec
MFC after: 1 week
handlers, some of which had to do awkward things to get a large enough
FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing NUL
byte. This behaviour was preserved, though it should not be necessary.
Reviewed by: phk
PCI status register to map its current name.
- Use PCIM_* rather than PCIR_* for constants for fields in various AER
registers. I got about half of them right in the previous commit.
MFC after: 1 week
K2 SATA controllers. The chip's status register must be read first, and
as a long, for other registers to be correctly updated after a command, and
this includes the command sequence in device detection as well as the
previously handled case after interrupts. While here, clean up some
previous hacks related to this controller.
Reported by: many
Reviewed by: mav
MFC after: 3 weeks
PCI-express. I used PCIZ_* for ID constants (plain capability IDs use
PCIY_*).
- Add register definitions for the Advanced Error Reporting, Virtual
Channels, and Device Serial Number extended capabilities.
- Teach pciconf -c to list extended as well as plain capabilities. Adds
more detailed parsing for AER, VC, and device serial numbers.
MFC after: 2 weeks
are still bound to BSP. It confuses timer management logic in per-CPU mode
and may cause timer not being reloaded. Check such cases on interrupt
arival and reload timer to give system some more time to manage proper
binding.
discrepencies from the igb version which was the target.
Change the message when neither MSI or MSIX are enabled
and a fallback to Legacy interrupts happen, the existing
message was confusing.
- add identify method to create driver's own device_t
- successfully probe only driver's own device_t instead of any device_t
- (ab)use device order to hopefully be probed/attached after acpi_wmi
PR: kern/147858
Tested by: Maciej Suszko <maciej@suszko.eu>
MFC after: 1 week
- Add special check for case when time expires before being programmed.
This fixes interrupt loss and respectively timer death on attempt to
program very short interval. Increase minimal supported period to more
realistic value.
- Add support for hint.hpet.X.allowed_irqs tunable, allowing manually
specify which interrupts driver allowed to use. Unluckily, many BIOSes
program wrong allowed interrupts mask, so driver tries to stay on safe
side by not using unshareable ISA IRQs. This option gives control over
this limitation, allowing more per-CPU timers to be provided, when FSB
interrupts are not supported. Value of this tunable is bitmask.
- Do not use regular interrupts on virtual machines. QEMU and VirtualBox
do not support them properly, that may cause problems. Stay safe by default.
Same time both QEMU and VirtualBox work fine in legacy_route mode.
VirtualBox also works fine if manually specify allowed ISA IRQs with above.
Both deadline and current_time are time_seconds (+ utc_offset())
casted to unsigned long long. No need to cast to or print as pointers.
MFC after: 4 days
to pad with 0xFF when it encounter short frames. According to RFC
1042 the pad bytes should be 0x00.
Because manual padding consumes extra CPU cycles, introduce a new
tunable which controls the padding behavior. Turning this tunable
on will have driver pad manually but it's disabled by default. Users
can enable software padding by setting the following tunable to
non-zero value.
dev.sis.%d.manual_pad="1"
PR: kern/35422 (patch not used)
prevented driver from working on big-endian machines. Also rewrite
station address programming to make it work on strict-alignment
architectures. With this change, sis(4) now works on sparc64 and
performance number looks good even though sis(4) have to apply
fixup code to align received frames on 2 bytes boundary on sparc64.
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
allmulti is toggled. Controller does not require reinitialization.
This removes unnecessary controller reinitialization whenever
tcpdump is used.
While I'm here remove unnecessary variable reinitialization.
configured TX/RX MACs before getting a valid link. After that, when
link state change callback is called, it called device
initialization again to reconfigure TX/RX MACs depending on
resolved link state. This hack created several bad side effects and
it required more hacks to not collide with sis_tick callback as
well as disabling switching to currently selected media in device
initialization. Also it seems sis(4) was used to be a template
driver for long time so other drivers which was modeled after
sis(4) also should be changed.
TX/RX MACs are now reconfigured after getting a valid link. Fix for
short cable error is also applied after getting a link because it's
only valid when the resolved speed is 100Mbps.
While I'm here slightly reorganize interrupt handler such that
sis(4) always read SIS_ISR register to see whether the interrupt is
ours or not. This change removes another hack and make it possible
to nuke sis_stopped variable in softc.
o Enforce TX/RX descriptor ring alignment. NS data sheet says the
controller needs 4 bytes alignment but use 16 to cover both SiS
and NS controllers. I don't have SiS data sheet so I'm not sure
what is alignment restriction of SiS controller but 16 would be
enough because it's larger than the size of a TX/RX descriptor.
Previously sis(4) ignored the alignment restriction.
o Enforce RX buffer alignment, 4.
Previously sis(4) ignored RX buffer alignment restriction.
o Limit number of TX DMA segment to be used to 16. It seems
controller has no restriction on number of DMA segments but
using more than 16 looks resource waste.
o Collapse long mbuf chains with m_collapse(9) instead of calling
expensive m_defrag(9).
o TX/RX side bus_dmamap_load_mbuf_sg(9) support and remove
unnecessary callbacks.
o Initial endianness support.
o Prefer local alignment fixup code to m_devget(9).
o Pre-allocate TX/RX mbuf DMA maps instead of creating/destroying
these maps in fast TX/RX path. On non-x86 architectures, this is
very expensive operation and there is no need to do that.
o Add missing bus_dmamap_sync(9) in TX/RX path.
o watchdog is now unarmed only when there are no pending frames
on controller. Previously sis(4) blindly unarmed watchdog
without checking the number of queued frames.
o For efficiency, loaded DMA map is reused for error frames.
o DMA map loading failure is now gracefully handled. Previously
sis(4) ignored any DMA map loading errors.
o Nuke unused macros which are not appropriate for endianness
operation.
o Stop embedding driver maintained structures into descriptor
rings. Because TX/RX descriptor structures are shared between
host and controller, frequent bus_dmamap_sync(9) operations are
required in fast path. Embedding driver structures will increase
the size of DMA map which in turn will slow down performance.
not change interrupt vector if it is not pointing the ROM itself. Actually,
we just fail shadowing altogether if that is the case because the shadowed
copy will be useless for sure and POST may not be relocatable or useful.
While I'm here, fix a debugging message under bootverbose, really. r211829
fixed one case but broke another. Mea Culpa.
or not by comparing reported TX consumer index with saved index. So
remove unnecessary check done after freeing transmitted mbufs.
While I'm here nuke unnecessary variable initializations.
tag. All controllers that are not BCM5755 or higher have 4GB
boundary DMA bug. Previously bge(4) used 32bit DMA address to
workaround the bug(r199670). However this caused the use of bounce
buffers such that it resulted in poor performance for systems which
have more than 4GB memory. Because bus_dma(9) honors boundary
restriction requirement of DMA tag for dynamic buffers, having a
separate TX/RX mbuf DMA tag will greatly reduce the possibility of
using bounce buffers. For DMA buffers allocated with
bus_dmamem_alloc(9), now bge(4) explicitly checks whether the
requested memory region crossed the boundary or not.
With this change, only the DMA buffer that crossed the boundary
will use 32bit DMA address. Other DMA buffers are not affected as
separate DMA tag is created for each DMA buffer.
Even if 32bit DMA address space is used for a buffer, the chance to
use bounce buffer is still very low as the size of buffer is small.
This change should eliminate most usage of bounce buffers on
systems that have more than 4GB memory.
More correct fix would be teaching bus_dma(9) to honor boundary
restriction for buffers created with bus_dmamem_alloc(9) but it
seems that is not easy.
While I'm here cleanup bge_dma_map_addr() and remove unnecessary
member variables in bge_dmamap_arg structure.
Tested by: marcel
heavy I/O load.
Many thanks to LSI for continuing to support FreeBSD.
PR: kern/149968
Submitted by: LSI (Tom Couch)
Reported by: Kai Kockro <kkockro web de>
Tested by: Kai Kockro, jpaetzel
MFC after: 7 days
configuration function. For failed memory allocations, em(4)/lem(4)
called panic(9) which is not acceptable on production box.
igb(4)/ixgb(4)/ix(4) allocated the required memory in stack which
consumed 768 bytes of stack memory which looks too big.
To address these issues, allocate multicast array memory in device
attach time and make multicast configuration success under any
conditions. This change also removes the excessive use of memory in
stack.
Reviewed by: jfv
Just showing some buffer allocation error is more appropriate
action for drivers. This should fix occasional panic reported on
em(4) when driver encountered resource shortage.
Reviewed by: jfv
supported by many BIOSes to improve performance of VESA BIOS calls for real
mode OSes but it is not our intention here. However, this may help some
platforms where the video ROMs are inaccessible after suspend, for example.
Note it may consume up to 64K bytes of contiguous memory depending on video
controller model when it is enabled. This feature can be disabled by
setting zero to 'debug.vesa.shadow_rom' loader tunable via loader(8) or
loader.conf(5). The default is 1 (enabled), for now.
ID, plus the ability to force '16-bit mode' which really means NE-2000
mode. Other open source drivers suggest that the Holtek misbehaves if
you allow the 8-bit probe. Also, all of the PCI chips emulate
NE-2000ish cards, so always force 16-bit mode for memory transfers.
PR: 84202 (patch not used)
I'm not sure whether adding this logical id is correct or not
because Compex RL2000 is in the list of supported hardware list.
I guess the Compex RL2000 could be PCI variant while the controller
in question is ISA controller. It seems PNP compat id didn't match
or it had multiple compat ids so isa_pnp_probe() seemed to return
ENOENT.
PR: kern/80853
support WOL. Some controllers require additional 3-wire auxiliary
remote wakeup connector to draw power. More recent xl(4)
controllers may not need the wakeup connector though.
initialize controller from a known good state. Previously driver
used to issue controller reset while TX/RX DMA are in progress.
I guess resetting controller in active TX/RX DMA cycle is to ensure
stopping I/Os in xl_shutdown(). I remember some buggy controllers
didn't respond with stop command if controller is under high
network load at the time of shutdown so resetting controller was
the only safe way to stop the I/Os. However, from my experiments,
controller always responded with stop command under high network
load so I think it's okay to remove the xl_reset() in
device_shutdown handler.
Resetting controller also will clear configured RX filter which
in turn will make WOL support hard because driver have to reprogram
RX filter in WOL handler as well as setting station address.
datagrams with checksum value 0 when TX UDP checksum offloading is
enabled. Generating UDP checksum value 0 is RFC 768 violation.
Even though the probability of generating such UDP datagrams is
low, I don't want to see FreeBSD boxes to inject such datagrams
into network so disable UDP checksum offloading by default. Users
still override this behavior by setting a sysctl variable or loader
tunable, dev.bge.%d.forced_udpcsum.
I have no idea why this issue was not reported so far given that
bge(4) is one of the most commonly used controller on high-end
server class systems. Thanks to andre@ who passed the PR to me.
PR: kern/104826
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.
This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.
Obtained from: Linux
AR5416 and later chipsets.
ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
flag immediately so it's only set once per longcal interval.
Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".
This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.
Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
o AR8151 v1.0(L1D) gigabit ethernet controller
o AR8151 v2.0(L1D) gigabit ethernet controller
o AR8152 v1.1(L2CB) fast ethernet controller
o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.
HW donated by: Atheros Communications, Inc.
- Increase target limit from 4 to 64; this limit will be removed entirely
at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.
Submitted by: Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by: Dansk Scanning A/S, Data Robotics Inc.
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.
hint.ste.0.prefer_iomap="1"
PR: kern/149285
MFC after: 5 days
suspend state. Also disable master clock after PHY power down,
this is supposed to save more power. The master clock should be
enabled if WOL is active.
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
vendor ID in the vendor section, and by symbolic name in the product
section. Products are sorted by product ID. While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.
MFC after: 1 week
value resulted in poor performance for UDP packets. With this
change, UDP bulk transfer performance is more than 940Mbps.
While I'm here fix a wrong register definition.
bus_generic_resume() since the pci_link(4) driver was added.
- Change the ACPI PCI-PCI bridge driver to inherit most of its methods
from the generic PCI-PCI bridge driver. In particular, this will now
restore PCI config registers for ACPI PCI-PCI bridges.
Tested by: Oleg Sharoyko osharoiko of gmail
infrastructure, not us. This appears to be a leftover from an older
version of the driver.
Submitted by: avg
Tested by: Anton Shterenlikht <mexas bristol.ac.uk>
MFC after: 1 week
X-MFC-Note: To stable/8 and stable/7 only
This way we would have an opportunity to hide the
Tj(target) value doesn't seem right stuff if we know
it's not working there.
Add temperature value for Core2 Duo Extreme Mobile that
I have access to.
Xeon 5500/5600 series:
- Utilize IA32_TEMPERATURE_TARGET, a.k.a. Tj(target) in place
of Tj(max) when a sane value is available, as documented
in Intel whitepaper "CPU Monitoring With DTS/PECI"; (By sane
value we mean 70C - 100C for now);
- Print the probe results when booting verbose;
- Replace cpu_mask with cpu_stepping;
- Use CPUID_* macros instead of rolling our own.
Approved by: rpaulo
MFC after: 1 month
a PMC. It was possible that we could have turned a bit on but
never cleared it.
Extend the calls to rdmsr() to all necessary functions, not
just those which previously caused a panic.
Pointed out by: jhb@
MFC after: 1 week
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
plug. Note that the Vendor ID 0x04b4 is officially assigned to Cypress,
so use that instead of adding a second vendor with an identical ID, in the
same way other similar cases are treated in usb/usbdevs.
PR: usb/132785
Submitted by: Dirk-Willem van Gulik <dirkx webweaving.org>
MFC after: 1 week
10G cards. 1G cards are x4 only.
- Use constants from pcireg.h for reading the current link width.
- Use pci_set_max_read_req() rather than implementing it by hand.
Reviewed by: np
MFC after: 1 week
This is similar to a fix in r189305 but for earlier ICH versions (<= 5).
Reported by: someone via attilio
Discussed with: des, attilio
MFC after: 1 week
tail pointers of the tx and rx queues. We needed a SYSCTL_PROC
to correctly get the values at run time.
Submitted by: Andrew Boyer aboyer at averesystems.com
MFC after: 1 week
This version adds support for ARC1880; additionally this version fixed
an issue where all devices on a SAS port gets offlined when any device
failed on the port [1].
Many thanks to Areca for continuing to support FreeBSD.
PR: kern/148502 [1]
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
Obtained from: Areca
Tested by: Rich Ercolani <rercola acm jhu edu> [1]
MFC after: 2 weeks
lengths. Make MI wrapper code to validate periods in request. Make kernel
clock management code to honor these hardware limitations while choosing hz,
stathz and profhz values.
- Fixed the interface probe routine to only attach to USB interfaces the driver
actually supports. This allows other drivers to attach to things like
MicroSD slots etc.
- Fixed network interface enumeration to be globally sequential instead of
relying on the USB interface numbers. This make sure the first network
interface always is at uhso0 and the second at usho1 and so on.
- Added a radio kill switch; exposed through sysctl.
- Updated the manual page to be verbose about the number of serial ports and
include iCON 452 in the set of tested hardware.
Submitted by: Fredrik Lindberg
calls. Also add BUS_DMA_COHERENT flag to bus_dmamem_alloc(9) to
take advantage of efficient synchronization for architectures that
support that feature.
Reviewed by: davidch
return code. If context was not setup correctly give up
initialization. While I'm here move variable declarations to the
beginning of the function.
Reviewed by: davidch
AcpiOsMapMemory()/AcpiOsUnmapMemory() (-> pmap_mapbios()/pmap_unmapbios())
for AcpiOsReadMemory() and AcpiOsWriteMemory(). Although they do not sound
too obvious, these functions are exclusively used to access memory mapped
IO in ACPICA.
According to ACPICA User Guide and Programmer Reference, the read data must
be zero extended to fill the 64-bit return value even if the bit width of
the location is less than 64.
- Return error when 64-bit access is requested as we do not support 64-bit
PCI register access (yet). XXX We may have to split it up into two 32-bit
accesses if it is really required.
According to ACPICA User Guide and Programmer Reference, the read data must
be zero extended to fill the 32-bit return value even if the bit width of
the port is less than 32.
- Remove 64-bit read/write from AcpiOsReadMemory() and AcpiOsWriteMemory().
These functions do not support 64-bit access (yet). Clean up style nits
and unnecessary bit masking while I am here.
Reported by: Liu, Jinsong (jinsong dot liu at intel dot com) via
Lin Ming (ming dot m dot lin at intel dot com) [1]
- The 6000 series WiMAX devices need a separate firmware.
- The b-gen devices are not hooked because the hardware revision type
is not know.
Obtained from: OpenBSD
MFC after: 1 week
r165114 added that code and that change ignored the same logic
committed in r135772. In addition, data FIFO protection should be
selectively enabled instead of applying to all PCIe devices.
While I'm here add BCM5785 to devices that do not require this
fix.
and remove a buffer overflow:
- Remove the array of per-type dispatch functions. Instead, pass each
structure to a single callback. The callback should check the type of
each table entry to take appropriate action. This matches the behavior
of other table walkers such as for the MP Table and MADT.
- Don't attempt to save an array of string pointers for each structure
entry. Instead, just skip the strings. If this code is reused to
provide a generic SMBIOS table walker in the future we could provide
a method that looks up a specific string N for a given structure record
instead of pre-populating an array of pointers. This fixes a buffer
overflow for structure entries with more than 20 strings.
PR: kern/148546
Reported by: Spencer Minear @ McAfee
MFC after: 3 days
The code in question verifies that all register write operations only change
bits that are defined (in the register definition file) for that effected
register. The bug effectively disabled this checking.
o Fix the check by testing the opcode against all supported read ("and" based)
operands.
o Add missing bit definitions to the aic7xxx and aic79xx register definition
files so that the warning (treated as a fatal error) does not spuriously
fire.
Reported by: Pawel Worach <pawel.worach@gmail.com>
MFC after: 1 week
All of the necessary wrmsr calls are now preceded by a rdmsr
and we leave the reserved bits alone.
Document the bits in the relevant registers for future reference.
Tested by: mdf
MFC after: 1 week
was missed in r209599.
Reported and tested by: Michael Moll
- Declare mpt_dma_buf_alloc() static just like mpt_dma_buf_free(), both are
used in mpt.c only.
Reviewed by: ken
MFC after: r209599
a packet has only a header in the first mbuf, the
checksum code will dereference a pointer into the
non-existing IP header. Do a check for the size and
pullup if needed. Thanks to Michael Tuexen for this
fix.
MFC: asap - should be in 8.1 IMHO
Do not grab lock while setting up interrupt, as it causes LOR with
allocation code. Instead make interrupt handler check that CAM bus
initialization completed before touching it.
While there, slightly improve attach errors handling.
Reported by: kib
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
start so we should adjust the mbuf if the driver is running in PIO mode.
Now it should work well with WPA authentication and association for LP
PHY devices.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 1 month
checksum offloading is enabled. The frame has a valid checksum
value so payload might be modified during TX checksum calculation.
Disable TX checksum offloading but give users chance to enable it
when they know their controller works without problems with TX
checksum offloading.
Reported by: Andrzej Tobola <ato <> iem dot pw dot edu dot pl>
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.
MFC after: 1 month
checksum is enabled in sge_init_locked().
While I'm here do not set RX checksum bits in RX descriptor
initialization. It is controller's job to set these bits.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
configuration to get IPv4 TSO work on BCM57780. While I'm here
apply the same fix to BCM5785 which shares similar hardware feature
of BCM57780. This change makes TSO work on BCM57780.
Tested by: Tong Liu <nemoliu <> gmail dot com>
it. This can happen in some cases when plugging in SD/SmartCard PC
Cards with empty slots. It is better to detect this bogosity, and
refuse to attach rather than panic with a division by zero (in one of
many places) down stream.
the core changes but left out the shared code, lol.
Well, and a couple fixes to the core... hopefully
this will all be complete now.
Happy happy joy joy :)
What this provides is support for the 'virtual function'
interface that a FreeBSD VM may be assigned from a host
like KVM on Linux, or newer versions of Xen with such
support.
When the guest is set up with the capability, a special
limited function 82576 PCI device is present in its virtual
PCI space, so with this driver installed in the guest that
device will be detected and function nearly like the bare
metal, as it were.
The interface is only allowed a single queue in this configuration
however initial performance tests have looked very good.
Enjoy!!
limit the advertised speed of an SFP+ to 1G, effectively
"forcing" link at that lower speed. It is off by default
and is enabled by sysctl dev.ix.0.force_gig=1, 0 will
set it back to the norm.
The mpt driver previously didn't report a 'maxio' size to CAM, and so the
da(4) driver limited I/O sizes to DFLTPHYS (64K) by default. The number
of scatter gather segments allowed, as reported to busdma, was
(128K / PAGE_SIZE) + 1, or 33 on architectures with 4K pages.
Change things around so that we wait until we've determined how many
segments the adapter can support before creating the busdma tag used for
buffers, so we can potentially support more S/G segments and therefore
larger I/O sizes.
Also, fix some things that were broken about the module unload path. It
still gets hung up inside CAM, though.
mpt.c: Move some busdma initialization calls in here, and call
them just after we've gotten the IOCFacts, and know how
many S/G segments this adapter can support.
mpt.h: Get rid of MPT_MAXPHYS, it is no longer used.
Add max_cam_seg_cnt, which is used to report our maximum
I/O size up to CAM.
mpt_cam.c: Use max_cam_seg_cnt to report our maximum I/O size to CAM.
Fix the locking in mpt_cam_detach().
mpt_pci.c: Pull some busdma initialization and teardown out and put
it in mpt.c. We now delay it until we know many scatter
gather segments the adapter can support, and therefore
how to setup our busdma tags.
mpt_raid.c: Make sure we wake up the right wait channel to get the
raid thread to wake up when we're trying to shut it down.
Reviewed by: gibbs, mjacob
MFC after: 2 weeks
This prevents a kernel fault by dividing with zero because the initial
rate was 0 and didn't be initialized.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 3 days
changed to RUN because ic->ic_newassoc isn't set anywhere now. In the
previous bwi_newassoc() is used to initialize AMRR rate routines.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 3 days
It has more features than acpi_aiboost(4) and it will eventually replace
acpi_aiboost(4).
Submitted by: Constantine A. Murenin <cnst at FreeBSD.org>
Reviewed by: freebsd-acpi, imp
MFC after: 1 month
FPU registers for copying. Remove the switch table and jumps from
bcopy/bzero/... to the actual implementation.
As a side-effect, i486-optimized bzero is removed.
Reviewed by: bde
Tested by: pho (previous version)
properly short terminate their transfers. This fixes a problem where input
appears several seconds late.
Reported by: Alexander Yerenkow
Submitted by: Hans Petter Selasky
HPET to steal IRQ0 from i8254 and IRQ8 from RTC timers. It can be suitable
for HPETs without FSB interrupts support, as it gives them two unshared
IRQs. It allows them to provide one per-CPU event timer on dual-CPU system,
that should be suitable for further tickless kernels.
To enable it, such lines may be added to /boot/loader.conf:
hint.atrtc.0.clock=0
hint.attimer.0.clock=0
hint.hpet.0.legacy_route=1
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
measured interval as upper bound. It should be more precise then just
assuming hz/2. For idle CPU it should be quite precise, for busy - not
worse then before.
state lower than the lowest one supported by the current CPU. This closes
some races with changes to the hw.acpi.cpu_cx_lowest sysctl while Cx
states for individual CPUs were changing (e.g. unplugging the AC adapter
of a laptop) that could result in panics.
Submitted by: Giovanni Trematerra
Tested by: David Demelier demelier dot david of gmail
MFC after: 3 days
Although the sysctls are marked with CTLFLAG_RD and the values will stay
immutable, current sysctl implementation stores value pointer in
void* type, which means that const qualifier is discarded anyway
and some newer compilers complaint about that.
We can't use de-const trick in sysctl implementation, because in that
case we could miss an opposite situation where a const value is used
with CTLFLAG_RW sysctl.
Complaint from: gcc 4.4, clang
MFC after: 2 weeks
beginning with the highest available rate. Currently we always use
54m for the first retry no matter what AMRR has choosen. Fix this
by setting the index to the next lower rate.
Approved by: rpaulo (mentor)
Tested by: Brandon Gooch <jamesbrandongooch at gmail.com>
MFC after: 2 weeks
callback function will be executed, and that the key won't be deleted during
the init process.
- txmic and rxmic are written into the chip the same place regardless of
opmode.
- Make the hardware generate 802.11 sequence numbers.
Submitted by: Akinori Furukoshi
Obtained from: git://gitorious.org/run/run.git
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
The T3 ASIC can provide an incoming packet's timestamp instead of its RSS hash.
The timestamp is just a counter running off the card's clock. With a 175MHz
clock an increment represents ~5.7ns and the 32 bit value wraps around in ~25s.
# sysctl -d dev.cxgbc.0.pkt_timestamp
dev.cxgbc.0.pkt_timestamp: provide packet timestamp instead of connection hash
# sysctl -d dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: core clock frequency (in KHz)
# sysctl dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: 175000
Remove unneeded rxtx handler, make que handler generic.
Do not allocate header mbufs in rx ring if not doing hdr split.
Release the lock in rxeof call to stack.
MFC for 8.1 asap
via %s
Most of the cases looked harmless, but this is done for the sake of
correctness. In one case it even allowed to drop an intermediate buffer.
Found by: clang
MFC after: 2 week
support FreeBSD.
1) Timeout ioctl command timeouts.
Do not reset the controller if ioctl command completed
successfully.
2) Remove G66_WORKAROUND code (this bug never shipped).
3) Remove unnecessary interrupt lock (intr_lock).
4) Timeout firmware handshake for PChip reset (don't wait forever).
5) Handle interrupts inline.
6) Unmask command interrupt ONLY when adding a command to the pending
queue.
7) Mask command interrupt ONLY after removing the last command from
the pending queue.
8) Remove TW_OSLI_DEFERRED_INTR_USED code.
9) Replace controller "state" with separate data fields to avoid races:
TW_CLI_CTLR_STATE_ACTIVE ctlr->active
TW_CLI_CTLR_STATE_INTR_ENABLED ctlr->interrupts_enabled
TW_CLI_CTLR_STATE_INTERNAL_REQ_BUSY ctlr->internal_req_busy
TW_CLI_CTLR_STATE_GET_MORE_AENS ctlr->get_more_aens
TW_CLI_CTLR_STATE_RESET_IN_PROGRESS ctlr->reset_in_progress
TW_CLI_CTLR_STATE_RESET_PHASE1_IN_PROGRESS ctlr->reset_phase1_in_progress
10) Fix "req" leak in twa_action() when simq is frozen and req is NOT
null.
11) Replace softc "state" with separate data fields to avoid races:
TW_OSLI_CTLR_STATE_OPEN sc->open
TW_OSLI_CTLR_STATE_SIMQ_FROZEN sc->simq_frozen
12) Fix reference to TW_OSLI_REQ_FLAGS_IN_PROGRESS in
tw_osl_complete_passthru()
13) Use correct CAM status values.
Change CAM_REQ_CMP_ERR to CAM_REQ_INVALID.
Remove use of CAM_RELEASE_SIMQ for physical data addresses.
14) Do not freeze/ release the simq with non I/O commands.
When it is appropriate to temporarily freeze the simq with an I/O
command use:
xpt_freeze_simq(sim, 1);
ccb->ccb_h.status |= CAM_RELEASE_SIMQ;
otherwise use:
xpt_freeze_simq(sim, 1);
xpt_release_simq(sim, 1);
Submitted by: Tom Couch <tom.couch lsi.com>
PR: kern/147695
MFC after: 3 days
- Re-enable TSO. This was broken previously due to CSUM_TSO clearing the
CSUM_TCP flag, so our checksum flags were incorrectly set going to the
netback driver. That was fixed in r206844 in tcp_output.c, so we can
turn TSO back on here.
- Fix the way transmit slots are calculated, so that we can't overfill
the ring.
- Avoid sending packets with more fragments/segments than netback can
handle. The Linux netback code can only handle packets of
MAX_SKB_FRAGS, which turns out to be 18 on machines with 4K pages. We
can easily generate packets with 32 or so fragments with TSO turned on.
Right now the solution is just to drop the packets (since netback
doesn't seem to handle it gracefully), but we should come up with a way
to allow a driver to tell the TCP stack the maximum number of fragments
it can handle in a single packet.
- Fix the way the consumer is tracked in the receive path. It could get
out of sync fairly easily.
- Use standard Xen ring macros to make it clearer how netfront is using
the rings.
- Get rid of Linux-ish negative errno return values.
- Added more documentation to the driver.
- Refactored code to make it easier to read.
- Some other minor fixes.
Reviewed by: gibbs
Reviewed by: gibbs
Sponsored by: Spectra Logic
MFC after: 7 days
corruption bug where if an ATA command is issued before DMA is started,
data will become available to the controller before it knows what to do
with it. This results in either data corruption or a controller crash.
This patch remedies the problem by adopting the workaround employed
by Linux and Darwin: starting the DMA engine prior to sending the ATA
command.
Observer on: Xserve G5
Reviewed by: mav
MFC after: 1 week
buffers it should also reinitialize RX descriptors otherwise some
stale data could be passed to controller. This could end up with
mbuf double free or unexpected NULL pointer dereference in upper
stack. To fix the issue, save loaded buffer's length and
reinitialize RX descriptors with the saved value whenever bge(4)
reuses the loaded RX buffers.
While I'm here, increase the number of RX buffers to 512 from 256.
This simplifies RX buffer handling as well as giving more RX
buffers. Controller supports just fixed number of RX buffers
(i.e. 512) and bge(4) used to rely on hope that our CPU is fast
enough to keep up with the controller. With this change, bge(4)
will use 1MB for RX buffers but I don't think it would cause
problems in these days.
Reported by: marcel
Tested by: marcel
fix. On Apple OpenPICs, the low/high bit of the interrupt sense is only
respected for interrupt 0. We currently erroneously program all OpenPIC
interrupts level high instead of level low by default, which only matters
for some G5 systems where the SATA controllers use IRQ 0.
This change is a quick fix that will be reverted once the effect of
changing the default interrupt sense on embedded systems is known.
MFC after: 3 days
context from in-kernel execution of padlock instructions and to handle
spurious FPUDNA exceptions that sometime are raised when doing padlock
calculations.
Globally mark crypto(9) kthread as using FPU.
Reviewed by: pjd
Hardware provided by: Sentex Communications
Tested by: pho
PR: amd64/135014
MFC after: 1 month
I don't know why- but it occurred to me in looking at the second sleep
is that all I want is a pause- not an actual sleep. So do that instead.
MFC after: 2 weeks
doing bidirectional stress traffic on 82598.
Also a couple bug fixes from Michael Tuexen, thank you!!
Add a workaround into the header so that 8 REL can use
the driver (adds local copy of ALTQ fix).
MFC: in a few days
o fdtbus(4) - the main abstract bus driver for all FDT-compliant systems. This
is a direct replacement for the many incompatible bus drivers grouping
integrated peripherals on embedded platforms (like obio(4), ocpbus(4) etc.)
o simplebus(4) - bus driver representing ePAPR style 'simple-bus' node, which
is an umbrella device for most of the integrated peripherals on a typical
system-on-chip device.
o Other components (common routines library, PCI node processing helper
functions)
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
I removed too many lines and a wrong pointer was accidentally passed down.
Tested by: Scott Allendorf (scott-allendorf at uiowa dot edu), kib
MFC after: 3 days
o Let OFW_INIT() and OF_init() return status value.
o Provide helper routines for 'compatible' property handling.
o Only compile OF and OFW code, which is relevant in FDT scenario.
o Other minor cosmetics
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
Make sure not to requeue freed mbuf in sge_start_locked(). This
should fix NULL pointer dereference panic.
Reported by: Nikolay Denev <ndenev <> gmail dot com>
Submitted by: jhb
device, make sure we have no real HPET device entry with same ID.
As side effect, it potentially allows several HPETs to be attached.
Use first of them for timecounting, rest (if ever present) could later
be used as event sources.
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
free(9) and it can cause kernel panic when there are multiple graphics
controllers in the system.
Tested by: Brandon Gooch (jamesbrandongooch at gmail dot com)
MFC after: 3 days
firmware in order to take over control of the SMU. Without doing this,
the firmware background process doing fan control will run amok as we
take over the system and crash the management chip.
This is limited to these two machines because our kernel is heavily
dependent on firmware accesses, and so quiescing firmware can cause
nasty problems.
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
USB enumeration lock is locked, then the USB stack fails to resume the device
because locking the USB enumeration lock is part of the resume procedure. To
solve this issue a new lock is introduced which only protects the suspend and
resume callbacks, which can be dropped inside the usbd_do_request_flags()
function, to allow suspend and resume during so-called enumeration operations.
Submitted by: Hans Petter Selasky
hardware tag insertion/stripping. Remove conditional code that
disables these hardware features on SiS190. Also nuke RX fixup code
which is no more required on strict-alignment architectures because
SiS190 supports RX 10 bytes padding.
Now all hardware features except jumbo frame and WOL are supported.
Thanks to Masa Murayama who confirmed SiS190 also has the same
hardware features of SiS191.
I guess the only difference between SiS191 and SiS190 would be
jumbo frame support. It will be implemented in near future.
fragmentation of mbuf chain to 32 from 16 because TSO can send 64KB
sized packet which in turn requires long list of mbuf chain. Due to
lack of documentation, I'm not sure whether driver have to pull up
ethernet/IP/TCP header with options to make controller work but
driver have to parse TCP header to update pseudo TCP checksum
anyway. The controller expects pseudo TCP checksum computed by
upper stack and the checksum should follow the MS NDIS
specification to make TSO work.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
MFC after: 5 days
from passive to active scans. Basicly disable it by increasing the
amount packets to be received to an amount which can't be reached
during dwell times.
Approved by: rpaulo (mentor)
MFC after: 3 days
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
is no more need to defragment mbufs. After transmitting the
multi-fragmented frame, the controller updates only the first
descriptor of multi-descriptor transmission so it's driver's
responsibility to clear OWN bits of remaining descriptor of
multi-descriptor transmission. It seems the controller behaves much
like jme(4) controllers in descriptor handling.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
received frames. Also check driver has valid ifp pointer before
calling msk_stop() in device_shutdown handler. While I'm here
remove unnecessary accesses to interrupt mask registers in
device_shutdown handler because driver puts the controller into
reset state.
With these changes, msk(4) now survive from heavy RX traffic(1byte
UDP frame) while reboot is in progress.
Reported by: Mark Atkinson < atkin901 <> gmail dot com >
by zero of the second argument 'from'.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Pointed out by: Andrew Reilly (areilly at bigpond dot net dot au)[1]
MFC after: 3 days
on Cassini using the external PCS SERDES otherwise unaligned access
traps and other strange effects happen with some machines. Don't touch
the MIF which is unused in that case either. These changes require the
PHY type to use to be determined via the OFW device tree or from the
VPD in machines without the former.
- Disable the SERDES pins of Saturn when not used in order to save power
and ensure they are enabled otherwise.
- In cas_attach() use the correct register offset for CAS_PCS_CONF_EN.
- Add some bus space barriers missing in the PCS code path.
These changes make the Sun GigaSwift Ethernet 1.0 MMF cards as well as
the on-board interfaces found in Sun Fire B100s Blade Server work.
PR: 144867
scope of the object lock in agp_i810.c. (In this specific case, the scope
of the object lock shouldn't matter, but I don't want to create a bad
example that might be copied to a case where it did matter.)
Reviewed by: kib
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
This bug would cause allocating sample-mode PMCs to fail with ENOMEM after allocating several counting-mode PMCs.
Approved by: jkoshy (mentor)
MFC after: 2 weeks
that generates a fatal bus trap. Normally, the chips are setup to do
128 byte DMA bursts, but when on this CPU, they can only safely due
4-byte DMA bursts due to this bug. Details of the exact nature of the
bug are sketchy, but some can be found at
https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and 6.
There's a small performance penalty associated with this workaround,
so it is only enabled when needed on the Atheros AR71xx platforms.
Unfortunately, this condition is impossible to detect at runtime
without MIPS specific ifdefs. Rather than cast an overly-broad net
like Linux/OpenWRT dues (which enables this workaround all the time on
MIPS32 platforms), we put this option in the kernel for just the
affected machines. Sam didn't like this aspect of the patch when he
reviewed it, and I'd love to hear sane proposals on how to fix it :)
Reviewed by: sam@
does. Without this change, Yukon Extreme seems to generate lots of
RX FIFO overruns even though controller has available RX buffers.
These excessive RX FIFO overruns generated lots of pause frames
which in turn killed devices plugged into switch. It seems there is
still occasional RX frame corruption on Yukon Extreme but this
change seems to fix the pause frame storm.
Reported by: jhb
Tested by: jhb
MFC after: 5 days
- Print device details only when verbose boot is enabled.
- Add debug output for shared memory access.
- Add debug statistics (checksum offload & VLAN frame counters).
- Modify TX path to update consumer index for each frame completed
rather than updating the consumer index only once for a group of
frames to improve small packet performance.
- Print driver/firmware pulse messages only when verbose boot
is enabled.
- Add debug sysctl to clear statistics.
- Fix more style(9) violations.
MFC after: 2 weeks
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
controller, I'm not sure whether this is also applicable to SiS190
so this feature is only activated on SiS191 controller.
In theory, controller reinitialization is not needed when VLAN tag
configuration is changed, but xclin said controller was not stable
whenever toggling VLAN tag bit. To address that, sge(4)
reinitialize controller for VLAN configuration which seems to work
as expected. VLAN tag information for TX/RX descriptor and
configure bit of RxMacControl register was found by xclin.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw > (initial version)
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
register. Due to lack of SiS190 controller, I'm not sure whether
this is also applicable to SiS190 so this feature is only activated
on SiS191 controller.
The controller can pad 10 bytes before DMAing a received frame to
RX buffer and received bytes include the padded bytes. This padding
is very useful on strict-alignment architectures because driver
does not have to copy received frame to align IP header on 4 bytes
boundary. It also gives better RX performance on non-strict
alignment architectures. Special thanks to xclin to give me
valuable register information. Without his enthusiastic trial and
errors this wouldn't be even possible.
While I'm here tighten validity check of received frame. Controller
clears RDS_CRCOK bit when it received bad CRC frames. xclin found
that using loop back testing.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
programs RX filter configuration. It seems RX MAC control register
is one of key registers to get various offloading features as well
as performance. Blindly clearing unrelated bits can result in
unexpected results.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.
To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.
Also enable detection of the AT controller absence on amd64.
Reviewed by: jhb
MFC after: 1 month
back in rxeof (I could see little point in taking it out),
and now release it before the stack entry.
Also, make it so the 82574 does not configure for multiqueue
when its not used in the stack.
On top of that, LLVM+Clang mis-compiles this code because of its register
allocator bug.
Analyzed by: Andrew Reilly (areilly at bigpond dot net dot au)
Reviewed by: ariff, rdivacky
MFC after: 3 days
In the end, it does help fixing /dev/io usage from multithreaded
processes.
- On i386 and amd64 the old behaviour is kept but multithreaded
processes must use the new interface in order to work well.
- Support for the other architectures is greatly improved, where
necessary, by the necessity to define very small things now.
Manpage update will happen shortly.
Sponsored by: Sandvine Incorporated
PR: threads/116181
Reviewed by: emaste, marcel
MFC after: 3 weeks
Open Firmware device tree in order to match what the PROM built-in
driver uses. This is especially important when netbooting Fujitsu
Siemens PRIMEPOWER250 as in that case the built-in driver isn't used
and the port facts PortSCSIID defaults to 0, conflicting with the
disk at the same address.
first descriptor in TSO case. Otherwise controller can generate bad
frames during TSO. To address it, make sure to pull up ethernet +
IP + TCP header with options in first buffer. Also ensure the
buffer length of the first descriptor for TSO covers entire ethernet
+ IP + TCP with options and setup additional Tx descriptor if the
first buffer includes TCP payload.
Tested by: Amar Takhar <verm <> darkbeer dot org >
MFC after: 1 week
Some of these cases should be safe in a non-atomic fashion, however
since all of the driver ioctls are locked, a lot of work is required to
fix it correctly. Just don't sleep now.
MFC after: 2 weeks
was chosen by lots of trial and errors. The chosen value shows
good interrupt moderation without additional latency.
Without this change, controller can generate more than 140k
interrupts per second under high network load.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw >
This time, abandon the use of busdma and start interacting with the VM
system directly. Make use of the new kmem_alloc_attr() which allows us
to easily allocate non-contiguous pages to back the GART table. This
should help a lot when starting or restarting X after the system has
been running for a while and memory has become fragmented.
MFC after: 2 weeks
* On 32 bit platforms we steal the upper 4 bits of the map handle
to store a unique map id.
* On 64 bit platforms we steal the upper 24 bits.
Resolves issues where the offsets that are handed to mmap may overlap the VRAM on some cards.
Tested on: radeon, intel, mga, and via.
This will break nouveau. I will spin new patches shortly.
proper device_t so it faked the devctl event to appear like one, this is now a
notify which allows more information to be passed.
We notify for both the device attach/detach and for each usb interface. A devd
rule can now match on the interface properties, including composite devices
which may have a uvideo interface and also usound and possibly uhid too.
An example to match a umass device with a scsi subclass and BBB protocol would be
notify 100 {
match "system" "USB";
match "subsystem" "INTERFACE";
match "type" "ATTACH";
match "intclass" "0x08";
match "intsubclass" "0x06";
match "intprotocol" "0x50";
action ...
};
The old attach devctl event has been retained for the moment to make merging to
8.1 easier. This was never compatible with 7.x or earlier due to the ugen regex
change needed.
Reviewed by: warner
MFC after: 1 week
occurs. In addition, the delay when programming the short cable fix
should be 100us, not 100ms.
PR: kern/64556
Submitted by: Thomas Hurst <tom at hur.st>
Approved by: rrs (mentor)
MFC after: 1 week
no flowid is present, this was causing some bad
reordering, now just use 0.
Also, add a few watchdog bits, and tx handler bits
that were corrected in igb.
- Re-probe xfp / sfp+ socket on link events, in case user
has changed transceiver
- correctly report current media to avoid confusing lagg (reported by Panasas)
- Report link speed (submitted by yongari)
Reviewed by: yongari (earlier version)
MFC after: 7 days
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
unneeded for legacy hardware.
Also remove some TSO related cruft.
Add some watchdog_time setting that was missing, thanks
to Mikolaj Golub for pointing that out.
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
set, it make sense to actually initialize that array. This fixes some
issues with 4965 adapters where the TX power is crucial.
This got lost somewhere while merging with the OpenBSD code.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
* Enable DC calibration and crystal calibration on Centrino Advanced-N
6250 parts.
* Workaround for a HW bug (does not affect 4965AGN) that may sporadically
affect latency under some rare circumstances. From a similar commit to
iwlwifi.
* Update sensitivity settings for 5000 series to workaround a performance
bug in the DSP (1000 is not affected so we keep the old values for 5000).
* Update sensitivity settings for 6000 series.
* Set differential gains on 6250 too (but use a 1.0 factor, not 1.5).
* Init OFDM sensitivity with min value (which depends on the chip)
instead of hardcoding it to 90.
* Read calibration version from ROM and set IWN_GP_DRIVER_CALIB_VER6
bit on 6x50 if version >= 6.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
- code flow in handler could let interrupt be
reenabled when not wanted.
- change where the RX lock is taken to improve
performance.
- adapter->msix is true for MSI systems also,
it needs to explicitly test for 82574, good one :)
- add CRC stripping to the RX side, this was handled
by some obscure code in rxeof previously, its easier
to simply have the hardware strip it now.
- Add back an ALTQ change that slipped between the cracks
- Add an update to the watchdog_time in the xmit code, not
doing this in ixgbe caused problems, think its needed here
as well.
VLAN HWFILTER from being used by default, this breaks
stacked pseudo devices, and as it turns out, also breaks
virtual machines that happen to use VLANS (didn't know that
before :). Put the fix back into the em driver, and for good
measure add the same code to the igb driver where it should
have been anyway.
Just relying on status LE ownership of status block seems to cause
poor performance. Always read current status index register first
and then check status ownership as we had before. Accessing status
index register seems to trigger immediate status update if
controller have pending status updates.
MFC after: 1 week
Reported by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
Tested by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
- Added some new debug helper routines to systcl.
- Fixed many of the style(9) violations that have crept into the code
due to my use of a "smart" editor.
MFC after: 2 weeks
set to sane values as they no longer default to 0, otherwise some OFW
implementation might copy in or out arguments not based on what the actual
function takes but what ever stack garbage nargs and nreturns supply.
Reviewed by: nwhitehorn
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
volumes were incorrectly calculated.
I've tested this with one of my es1370 cards and I can confirm that it
works.
PR: 98167
Submitted by: Joseph Terner <jtsn@gmx.de>
Approved by: kib
change the argument type to igb_rxeof() to the
correct type. Note, any users of POLLING must
be sure and set the number of queues to 1 for
things to work correctly.
- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.
- Use 16k jumbo clusters only on offload capable cards by default.
- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.
- Slightly better freelist size calculation.
- Fix nmbjumbo4 typo, remove unneeded global variables.
MFC after: 3 days
also for finding a one character bug that kept TSO from working.
Sometimes with direct attach cables a failure can occur in init,
the old method of calling detach was broken, there is no way to
return an error to the system from init, so I have changed it to
return failure thru the ioctl.
And, have fixed the ALTQ code changes of Max Laier, sorry Max :)
em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.
igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.
MFC in a week
- add some new hardware support for 82599
- Big change to interrupt architecture, it now
uses a queue which contains an RX/TX pair as
the recipient of the interrupt. This will reduce
overall system interrupts/msix usage.
- Improved RX mbuf handling: the old get_buf routine
is no longer synchronized with rxeof, this allows
the elimination of packet discards due to mbuf
allocation failure.
- Much simplified and improved AIM code, it now
happens in the queue interrupt context and takes
into account both the traffic on the RX AND TX
side.
- variety of small tweaks, like ring size, that have
been seen as performance improvements.
- Thanks to those that provided feedback or suggested
changes, I hope I've caught all of them.
on debug output. Add a new platform function requirement to allow
for printing based upon the ITL nexus instead of the isp unit plus
channel, target and lun. This allows some printouts and error messages
from the core code to appear in the same format as the platform's
subsystem (in FreeBSD's case, CAM path).
MFC after: 1 week
First, we compare mode table data against minimum value. If the mode table
does not make sense, we set the minimum in the mode info. When we actually
set the mode, we try VESA BIOS function and compare it against the previous
value. If it makes more sense, update the information.
Andrew Turner. The kernel supports the LN2410SBC evaluation board,
and likely others. These parts (or similar ones) are in some open
hardware designs for phones.
Submitted by: Andrew Turner
- Don't leak slice resources when mxge_alloc_rings() fails
- Start taskq threads only after we know attach will succeed. At
boot time, taskqueue_terminate() will loop infinately, waiting
for the threads to exit, and hang the system.
Submitted by: Panasas
MFC After: 3 days
Untangle some of the confusion about what role means when it's in the FCPARAM/SDPARAM
or isp_fc/isp_spi structures. This fixed a problem about seeing targets appear if you've
turned off autologin and find them, or rather don't, via camcontrol rescan.
MFC after: 1 month
